|
|
含有初始弯曲柔性梁的四杆机构轨迹分析
|
Abstract:
根据初始弯曲柔性梁的3R伪刚体模型，构建了含有初始弯曲柔性梁的四杆机构的仿真模型，并在ADAMS软件中进行建模仿真，输出伪刚体模型的末端轨迹和末端转角，并和ANSYS软件中建立的刚柔耦合模型输出结果以及基于1R伪刚体模型建立的机构仿真模型输出结果进行对比，可以对3R伪刚体模型进行验证是否可行、优越，为更广泛应用初始弯曲柔性梁打下了坚实的基础。
Based on the 3R pseudo-rigid body model of an initially curved flexible beam, the article constructed a simulation model of a four-bar mechanism that incorporates the initially curved flexible beam. The modeling and simulation were conducted using ADAMS software, and the end trajectory and end angle of the pseudo-rigid body model were output. These results were then compared with the output from the rigid-flexible coupling model established in ANSYS software and the output from the mechanism simulation model based on the 1R pseudo-rigid body model. This comparison facilitates the verification of the feasibility and advantages of the 3R pseudo-rigid body model, thereby laying a solid foundation for the broader application of initially curved flexible beam.
| [1] | (美)豪厄尔(Howell, L.L.). 柔顺机构学[M]. 余跃庆, 译. 北京: 高等教育出版社, 2007. |
| [2] | 高峰. 机构学研究现状与发展趋势的思考[J]. 机械工程学报, 2005, 41(8): 3-17. |
| [3] | 于靖军, 裴旭, 毕树生, 宗光华, 张宪民. 柔性铰链机构设计方法的研究进展[J]. 机械工程学报, 2010, 46(13): 2-13. |
| [4] | Howell, L.L. and Midha, A. (1994) A Method for the Design of Compliant Mechanism with Small-Length Flexural Pivots. Journal of Mechanical Design, 116, 280-289. https://doi.org/10.1115/1.2919359 |
| [5] | Howell, L.L. and Midha, A. (1996) Evaluation of Equivalent Spring Stiffness for Use in a Pseudo Rigid Body Model of Large Deflection Compliant Mechanisms. Journal of Mechanical Design, 118, 126-140. https://doi.org/10.1115/1.2826843 |
| [6] | Su, H.J. (2009) A Pseudorigid-Body 3R Model for Determining Large Deflection of Cantilever Beams Subject to Tip Loads. Journal of Mechanisms and Robotics, 1, Article 021008. https://doi.org/10.1115/1.3046148 |
| [7] | 冯忠磊, 余跃庆, 王雯静. 柔顺机构中大变形柔性梁的2自由度伪刚体模型[J]. 机械设计与研究, 2010, 26(3): 41-48. |
| [8] | 余跃庆, 徐齐平, 周鹏. 复合载荷作用下柔顺机构的PR伪刚体新模型[J]. 机械工程学报, 2013, 49(15): 9-14. |
| [9] | Howell, L.L. and Midha, A. (1996) Parameteric Deflection Approximations for Initially Curved, Large-Deflection Beams in Compliant Mechanisms. Proceedings of the 1996 ASME Design Engineering Technical Conferences and Computers in Engineering Conference, Irvine, 18-22 August 1996, 1-8. https://doi.org/10.1115/96-DETC/MECH-1215 |
| [10] | 李渊, 杜秋月. 末端加载力的初始弯曲柔性梁3R伪刚体模型[J]. 机械设计与研究, 2021, 37(5): 47-52. |
| [11] | 杨毅, 鹿碧洲, 李小毛, 等. 一种2自由度柔顺移动并联机构研究及其在对接装置上应用[J]. 机械工程学报, 2019, 55(11): 114-122. |
| [12] | 杨云良. 低温红外镜头柔性卸载结构设计与测试[D]: [硕士学位论文]. 廊坊: 北华航天工业学院, 2021. |
| [13] | 王家成. 多维微振动辅助悬浮混合水凝胶3D打印研究[D]: [硕士学位论文]. 大连: 大连交通大学, 2023. |
