|
|
Material Sciences 2023
城轨车辆用某型铝合金框架结构失效分析
|
Abstract:
本文针对城轨车辆用某型7XXX系铝合金框架结构出现的裂纹问题，采用光学金相、扫描电镜、透射电镜等表征手段进行了失效分析，探明了结构故障的原因，同时结合有限元分析揭示了材料的失效机理。结果表明，本文所述铝合金框架结构故障类型为环境腐蚀和疲劳耦合作用引起的开裂。其主要微观机理在于，材料本身晶界析出相呈连续分布，耐蚀性能不足，在焊接热影响下，容易使得材料形成晶内析出相数量减少，晶界连续分布着粗大析出相的组织特征，从而容易在腐蚀环境和疲劳载荷的作用下产生失效；有限元分析结果表明，该故障位置最低寿命约105.2次，约74万Km，与实际寿命基本吻合。
A crack incident of an Al-Zn-Mg alloy based frame structure of urban rail vehicles was investigated in this paper. Optical Metallography (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM) were conducted to the failure analysis. The mechanisms of the crack were revealed by joint results of microstructure analysis and finite ele-ment analysis. The results showed that the cracks on the frame structure were attributed to the coupling effects of environmental corrosion and fatigue. The exact failure mechanism was that the precipitated phase at the grain boundary of the material itself is continuously distributed, and the corrosion resistance is insufficient. On the effects of welding heat, it was easy to reduce the number of intragranular precipitated phase, and the precipitation on grain boundary was continuously dis-tributed with the structural characteristics of coarse precipitated phase, which is easy to cause fail-ure under the effect of corrosion environment and fatigue load. The results of finite element analy-sis showed that the minimum life of the cracking position is about 105.2 cycles, which tallies with the reality service life of the studied frame structure.
| [1] | 朱向东. 铝合金搅拌摩擦焊工艺研究及其在城轨车辆车体上的应用[D]: [硕士学位论文]. 长沙: 湖南大学, 2011. |
| [2] | 王炎金, 丁国华, 王俊玖. 铝合金车体制造技术在中国的发展现状和展望[J]. 焊接, 2004(10): 5-7. |
| [3] | Dzab, C., Hcjac, D., Zjcab, C., et al. (2022) Synchronous Improvement of Mechanical Properties and Stress Corrosion Resistance by Stress-Aging Coupled with Natural Aging Pre-Treatment in an Al-Zn-Mg Alloy with High Re-crystallization Fraction. Journal of Materials Science & Technology, 121, 40-51. |
| [4] | 王立航, 方吉, 马纪军. 铝合金车体疲劳寿命预测新方法及其应用[J]. 大连交通大学学报, 2010, 31(3): 3. |
| [5] | 李磊, 臧兰兰, 郎艳, 等. 基于BS EN 1993-1-9-2005的城轨车辆车体结构疲劳寿命分析[J]. 电力机车与城轨车辆, 2022, 45(2): 67-71, 80. |
| [6] | Peng, N.H., Zhan, L.H., Ma, B.L., et al. (2022) Creep Aging Behavior and Performance of Al-Zn-Mg-Cu Al-loys under Different Parameters in Retrogression Aging Treatment. Journal of Central South University, 29, 986-998.
https://doi.org/10.1007/s11771-022-4955-3 |
| [7] | 张健, 程石来, 朴圣君, 等. 某车型铝合金车体过渡边梁焊接裂纹分析[J].轨道交通装备与技术, 2021(3): 32-34. |
| [8] | 卢耀辉, 张德文, 赵智堂, 等. 焊接残余应力对动车组铝合金车体疲劳强度的影响[J]. 交通运输工程学报, 2019, 19(4): 94-103. |
| [9] | Fan X, Jiang D, Li Z, et al. (2007) In-fluence of Microstructure on the Crack Propagation and Corrosion Resistance of Al-Zn-Mg-Cu Alloy 7150. Materials Characterization, 58, 24-28. https://doi.org/10.1016/j.matchar.2006.03.003 |
| [10] | Li, H.Z., Yao, S.C., Liang, X.P., et al. (2016) Grain Boundary Pre-Precipitation and Its Contribution to Enhancement of Corrosion Resistance of Al-Zn-Mg Alloy. Transactions of Nonferrous Metals Society of China, 26, 2523-2531.
https://doi.org/10.1016/S1003-6326(16)64378-9 |
| [11] | Li, S., Dong, H., Shi, L., et al. (2017) Corrosion Behavior and Mechanical Properties of Al-Zn-Mg Aluminum Alloy Weld. Corrosion Science, 123, 243-255. https://doi.org/10.1016/j.corsci.2017.05.007 |
| [12] | Zhaoming, L.I., Jiang, H., Yan, D., et al. (2019) Effect of Minor Sc on Microstructure and Properties of Al-Zn-Mg Alloy Weld Joint. Chinese Journal of Materials Research, 33, 673-682. |
| [13] | EN 12663-1:2010. (2015) Railway Applications—Structural Requirements of Railway Vehicle Bod-ies—Part 1: Locomotives and Passenger Rolling Stock (and Alternative Method for Freight Wagons). The British Stand-ards Institution. BSI Standards Limited. |
