The mechanical performance of knitted fabric was significantly affected by loop density and geometries. Knitted fabric composites occupy a special position in the field of engineering materials because of their easy to form complex components and high impact energy absorption. But Knitted fabric composites have low in-plane tensile strength because the yarns are in a loop structure in the materials. Sound insulation requirements in automobiles, manufacturing environments, and equipment, generating higher sound pressure drive the need to develop more efficient and economical ways of producing sound absorption materials. The knitted fabric based acoustic materials were produced from cut wastes from different garment industries for their sound absorption property test as per the method described in ASTM E 1050. The acoustic performance of knitted fabrics was measured by independent tube methods for sound waves of 1000-6000 Hz. It is observed that the knitted fabrics acoustic materials prepared from waste materials showed high sound absorption than woven fabrics made from the same synthetic fibers. Moreover, the test revealed that blended knitted fabric had a better sound absorption property.
References
[1]
Ramakrishna, S. and Hull, D. (1991) Mechanical Properties of Knitted Fabric Composites. Proceedings of the Eighth International Conference on Composite Materials, Honolulu, 15-19 July 1991, A1-A10.
[2]
Offermann, P. (1997) Biaxial Reinforced Knitted Fabrics for Composite Reinforcement. Promotional Leaflet, Technische Universität Dresden, Dresden.
[3]
Ramakrishna, S. and Hull, D. (1994) Tensile Behaviour of Knitted Carbon-Fibre-Fabric/Epoxy Laminates—Part II: Prediction of Tensile Properties. Composites Science and Technology, 50, 249-258. https://doi.org/10.1016/0266-3538(94)90146-5
[4]
Andersson, C.H. and Eng, K. (1993) Split Film Based Weft Insert Warp Co-Knitting and Lost Yarn Preforming, Two New Routes for Composite Materials Preforming. Proceedings of the ECCM, 6, 237-242.
[5]
Ramakrishna, S., Fujita, A., Cuong, N.K. and Hamada, H. (1995). Tensile Failure Mechanisms of Knitted Glass Fibre Fabric Reinforced Epoxy Composites. Proceedings of the Fourth Japan International SAMPE Symposium, Tokyo, 24-28 September 1995, 661-666.
[6]
Ko, F.K., Krauland, K. and Scardino, F. (1982) Weft Insertion Warp Knit for Hybrid Composites. In: Hayashi, T., Kawata, K. and Umekawa, S., Eds., Proceedings of ICCM-IV, Tokyo, 25-28 October 1982, 1169-1176.
[7]
Rudd, C.D., Owen, M.J. and Middleton, V. (1990) Mechanical Properties of Weft Knit Glass Fibre/Polyester Laminates. Composites Science and Technology, 39, 261-277. https://doi.org/10.1016/0266-3538(90)90045-7
[8]
Phillips, D., Verpoest, I. and van Raemdonck, J. (1996) 3D-Knitted Fabrics for Sandwich Panels. Texcomp-3. 18/1.
[9]
Anand, S. (1996) Warp Knitted Structures in Composites. Proceedings of the Seventh European Conference in Composite Materials, London, 14-16 May 1996, 407-413.
[10]
Stumpf, H., Mader, E., Baeten, S., Pisanikovski, T., Zah, W., Eng, K., Anderson, C.H., Verpoest, I. and Schulte, K. (1996) New Thermoplastic Composite Preforms Based on Split-Film Warp-Knitting. Texcomp-3. 20/1.
[11]
Wu, W.L., Kotaki, M., Fujita, A., Hamada, H., Inoda, M. and Maekawa, Z. (1993) Mechanical Properties of Warp-Knitted Fabric-Reinforced Composites. Journal of Reinforced Plastics and Composites, 12, 1096-1110. https://doi.org/10.1177/073168449301201006
[12]
Ramakrishna, S. (1997) Analysis and Modeling of Plain Knitted Fabric Reinforced Composites. Journal of Composite Materials, 31, 52-70. https://doi.org/10.1177/002199839703100104
[13]
Gibbon, J. (1994) Knitting in the Third Dimension. Textile Horizons, 14, 22-25.
[14]
Huang, Z.M. and Ramakrishna, S. (1999) Development of Knitted Fabric Reinforced Composite Material for Prosthetic Application. Advanced Composites Letters, 8, 289-294. https://doi.org/10.1177/096369359900800603
[15]
Kosuge, K., Takayasu, A. and Hori, T. (2005) Recyclable Flame Retardant Nonwoven for Sound Absorption. Journal of Materials Science, 40, 5399-5405. https://doi.org/10.1007/s10853-005-4338-9
[16]
Zhou, H., Li, B., Huang, G.S. and He, J. (2007) A Novel Composite Sound Absorber with Recycled Rubber Particles. Journal of Sound and Vibration, 304, 400-406. https://doi.org/10.1016/j.jsv.2007.02.024
[17]
Ersoy, S. and Küçük, H. (2009) Investigation of Industrial Tea-Leaf-Fibre Waste Material for Its Sound Absorption Properties. Marmara University, Department of Mechatronics Education, Istanbul.
[18]
Mohanty, A.R. and Fatima, S. (2014) Noise Control Using Green Materials. Sound & Vibration, 49, 13-15.
[19]
Möser, M. (2004) Engineering Acoustics. Springer, New York.
[20]
Zhang, J.C., et al. (2018) Sound Absorption Characterization of Natural Materials and Sandwich Structure Composites. Aerospace, 5, Article No. 75. https://doi.org/10.3390/aerospace5030075
