A
composite material is made up of two phases, the matrix, and the reinforcing materials. The reinforcing material is embedded
over matrix material. The reinforcing material works to make the matrix
material harder. A fibreglass reinforced composite was developed using E-glass
fibre reinforcement and epoxy resin matrix. The composites were produced using
the hand lay-up technique with varying fibre percentage of 9%, 13% and 25% by
weight percentage of fibreglass mat at orientations of 0°, 15°, 45°, and 90° chosen at random. A 13% by weight percentage of chopped mat was also developed
for purpose of comparison. The fabricated composites were subjected to tensile
test, flexural test, impact test, punch shear test and hardness test to
ascertain the appropriate fibre contents and orientation that is optimum for
the manufacture of headgears. Analysis of Variance was carried out to determine
level of significance and percentage
contribution of the parameters. The results show that both fibre
orientation and percentage of fibre content reinforcement of have significant
influence on the strength and fracture energy of the composite .The fibre
orientation has a higher impact on the strength of the composite (79.74%) while
the percentage of fibre reinforcement has a lesser impact on the tensile
strength of the composite (20.26%).However, the fibre orientation has a lesser impact on the fracture
energy of the composite (24.54%) while the percentage of fibre
reinforcement has a higher impact on the fracture energy of the composite
(75.46%) The result from this study shows that the increase in fibre content
increases flexural strength and impact toughness of the fibreglass
References
[1]
Gujja, S.K., Sunil, C.H. and Joe, J. (2014) Fabrication of Glass Fibre Helmet. Proceedings of the International Conference on Information, Engineering, Management and Security (ICIEMS), 156-169.
[2]
Watson, J.C. and Raghupathi, N. (1987) Glass Fibres. In: Composites, Engineered Materials Handbook, Vol. 1, ASM International, Almere, 107.
[3]
Hoge, J. and Leach, C. (2016) Epoxy Resin Infused Boat Hulls. Reinforced Plastics, 60, 221-223. https://doi.org/10.1016/j.repl.2016.01.002
[4]
Gargano, A., Pingkarawat, K., Blacklock, M., Pickerd, V. and Mouritz, A.P. (2017) Comparative Assessment of the Explosive Blast Performance of Carbon and Glass Fibre-Polymer Composites Used in Naval Ship Structures. Composite Structures, 171, 306-316. https://doi.org/10.1016/j.compstruct.2017.03.041
[5]
Marsh, G. (2003) Material Trends for FRP Boats. Reinforced Plastics, 47, 23-26.
https://doi.org/10.1016/S0034-3617(03)00931-7
[6]
Qin, F.X., Peng, H.X., Chen, Z., Wang, H., Zhang, J.W. and Hilton, G. (2013) Optimization of Microwire/Glass-Fibre Reinforced Polymer Composites for Wind Turbine Application. Applied Physics A, 113, 537-542.
https://doi.org/10.1007/s00339-013-7820-2
[7]
Tanasa, F. and Zanoaga, M. (2013) Fibre-Reinforced Polymer Composites as Structural Materials for Aeronautics. Proceedings of the International Conference of Scientific Paper, Brasov, 1-3 June 2013, 23-25.
Wallenberger, F.T. (1994) Melt Viscosity and Modulus of Bulk Glasses and Fibres: Challenges for the Next Decade. Present State and Future Prospects of Glass Science and Technology. Proceedings of the Norbert Kreidl Symposium, Triesenberg, 3-8 July 1994, 63-78.
[10]
Gupta, N., Balrajsinghbrar and Eyassuwoldesenbet (2001) Effect of Filler Addition on the Compressive and Impact Properties of Glass Fibre Reinforced Epoxy. Bulletin of Materials Science, 24, 219-223. https://doi.org/10.1007/BF02710105
[11]
Pardo, S., Baptiste, D. and Decobert, D. (2002) Tensile Dynamic Behaviour of a Quasi-Unidirectional E-Glass/Polyester Composite. Composites Science and Technology, 62, 579-584. https://doi.org/10.1016/S0266-3538(01)00152-X
[12]
Mamalis, A., Manolakos, D., Demosthenous, G. and Ioannidis, M. (1996) Energy Absorption Capability of Fibre Glass Composite Square Frusta Subjected to Static and Dynamic Axial Collapse. Thin-Walled Structures, 25, 269-295.
https://doi.org/10.1016/0263-8231(95)00057-7
[13]
Hajiaghamar, M., Seidi, M., Fergson, J.R. and Caccese, V. (2015) Measurement of Head Impact Due to Standing Fall in Adults Using Anthropometric Test Dummies. Annals of Biomedical Engineering, 43, 2143-2152.
https://doi.org/10.1007/s10439-015-1255-1
[14]
Adekomaya, O. and Adama, K. (2017) Glass-Fibre Reinforced Composites: The Effect of Fibre Loading and Orientation on Tensile and Impact Strength. Nigerian Journal of Technology (NIJOTECH), 36, 782-787.
[15]
Wallenberger, F.T. (2010) Commercial and Experimental Glass Fibres. In: Wallenberger, F.T. and Bingham, P.A., Eds., Fibreglass and Glass Technology, Springer US, Berlin, 3-90. https://doi.org/10.1007/978-1-4419-0736-3_1
[16]
El-wazery, M.S., EL-Elamy, M.I. and Zoalfakar, S. (2017) Mechanical Properties of Glass Fibre Reinforced Polyester Composites. International Journal of Applied Science and Engineering, 14, 121-131.
[17]
Aramide, F.O., Atanda, P.O. and Olorunniwo, O.E. (2012) Properties of a Polyester Fibre Glass Composite. International Journal of Composite Materials, 2, 147-151.
https://doi.org/10.5923/j.cmaterials.20120206.06
[18]
Kumar, M.S., Raju, N.M.S., Sampath, P.S. and Vivek, U. (2015) Tribological Analysis of Nano Clay/Epoxy/Glass Fibre by Using Taguchi’s Technique. Materials & Design, 70, 1-9. https://doi.org/10.1016/j.matdes.2014.12.033
[19]
Cochran and Cox (1957) Randomized Complete Block Designs, Adapted from Experimental Designs. 2nd Edition, John Wiley & Sons, Inc., Hoboken.
