|
|
- 2019
天然纤维/环氧树脂-混凝土的力学性能及老化规律天然纤维/环氧树脂-混凝土的力学性能及老化规律
|
Abstract:
环氧树脂-混凝土是由混合树脂、固化剂和砂石骨料等原料固化成型的一种复合材料，因其优异的性能已成为土木与建筑应用中富有潜力的新型工程材料。本文将高性能的天然纤维（剑麻和苎麻）引入环氧树脂-混凝土中，以进一步增强其力学性能。实验结果表明，极少含量的天然纤维便能够提升环氧树脂-混凝土的抗弯拉强度，体积分数为0.36vol%的剑麻纤维和苎麻纤维可以将混凝土的抗弯拉强度分别提高10.5%和8.4%。天然纤维对环氧树脂-混凝土抗弯拉强度的增强效应可以用基于混合率的并联模型描述，模型预测结果与实测结果相比，相对误差低于5.1%。利用紫外光耐气候试验箱模拟华南地区自然环境的日照辐射和湿热条件，研究了天然纤维/环氧树脂-混凝土抗弯拉性能随老化时间的衰减。当等效老化时间为6年时，天然纤维/环氧树脂-混凝土的抗弯拉强度分别下降了14.3%（剑麻纤维）和15.9%（苎麻纤维）。实验观察到的衰减规律可采用复合材料湿热老化的剩余强度模型描述。 Epoxy polymer-concrete is a kind of composite material prepared by mixing epoxy resin, curing agent and aggregate. It has become a type of novel engineering material with great potential in civil and architectural applications, due to its excellent performance. In this paper, the high performance natural fibers (sisal and ramie) were incorporated into epoxy polymer-concrete to further enhance their mechanical properties. The experimental study shows that the flexural strength of epoxy polymer-concrete can be improved with natural fibers at very low loadings. 0.36vol% natural fibers lead to the increases in flexural strength by 10.5% (ramie fibers) or 8.4% (sisal fibers). The reinforcing effects of natural fibers on the flexural performance of epoxy polymer-concrete can be well described by the parallel model based on the rule of mixture. The theoretical prediction achieves a good agreement with the measured values, with small relative deviation less than 5.1%. The ultraviolet radiation and hygrothermal conditions of natural environment in south China were simulated using a UV accelerated weathering chamber, to the flexural performance decay of natural fiber/epoxy polymer concrete during aging. After the aging of 6 years (equivalent aging time), the flexural strength of natural fiber/epoxy polymer-concrete decreases by 14.3% (sisal fiber) and 15.9% (ramie fiber). The attenuation rule can be described using the residual strength model of fiber reinforced polymer composites in hygrothermal environment. 国家自然科学基金（11772131；11712132；11712134
| [1] | BEDI R, CHANDRA R, SINGH S P. Mechanical properties of polymer concrete[J]. Journal of Composites, 2013(8):1-12. |
| [2] | FOWLER D W. Polymers in concrete:A vision for the 21st century[J]. Cement and Concrete Composites, 1999, 21(5-6):449-452. |
| [3] | 李宇峙, 李家庆, 李星星, 等. 环氧树脂混凝土抗压强度和弹性模量的试验研究[J]. 公路, 2007(9):173-177. LI Yuzhi, LI Jiaqing, LI Xingxing, et al. Experimental study on compressive strength and elastic modulus of epoxy resin concrete[J]. Highway, 2007(9):173-177(in Chinese). |
| [4] | AVCI A, AKDEMIR A, ARIKAN H. Mixed-mode fracture behavior of glass fiber reinforced polymer concrete[J]. Cement and Concrete Research, 2005, 35(2):243-247. |
| [5] | 蒋持平, 邹振祝. 高速运动裂纹的分叉角问题[J]. 固体力学学报, 1991(3):269-273. JIANG Chiping, Zou Zhenzhu. Bifurcation angles of a crack propagating at a high speed[J]. Acta Mechanica Solida Sinica, 1991(3):269-273(in Chinese). |
| [6] | 邓宗才. 混杂纤维增强超高性能混凝土弯曲韧性与评价方法[J]. 复合材料学报, 2016, 33(6):1274-1280. DENG Zongcai. Flexural toughness and characterization method of hybrid fibers reinforced ultra-high performance concrete[J]. Acta Materiae Compositae Sinica, 2016, 33(6):1274-1280(in Chinese). |
| [7] | REIS J M L, OLIVEIRA R D, FERREIRA A J M, et al. A NDT assessment of fracture mechanics properties of fiber reinforced polymer concrete[J]. Polymer Testing, 2003, 22(4):395-401. |
| [8] | 王春红, 林天扬, 龙碧璇, 等. 聚乙烯醇交联改性对天然纤维增强聚丙烯复合材料性能的影响[J]. 复合材料学报, 2017, 34(9):1902-1910. WANG Chunhong, LIN Tianyang, LONG Bixuan, et al. PVA crosslinking modification effect on the properties of natural fiber reinforced polypropylene composites[J]. Acta Materiae Compositae Sinica, 2017, 34(9):1902-1910(in Chinese). |
| [9] | PACHECO-TORGAL F, JALALI S. Cementitious building materials reinforced with vegetable fibers:A review[J]. Construction and Building Materials, 2011, 25(2):575-581. |
| [10] | REIS J M L, FERREIRA A J M.. Freeze-thaw and thermal degradation influence on the fracture properties of carbon and glass fiber reinforced polymer concrete[J]. Construction and Building Materials, 2006, 20(10):888-892. |
| [11] | LI Y, MAI Y W, YE LIN. Sisal fiber and its composites:A review of recent developments[J]. Composites Science and Technology, 2000, 60(11):2037-2055. |
| [12] | 交通部公路科学研究所. 公路工程水泥及水泥混凝土试验规程:JTG E30-2005[S]. 北京:人民交通出版社, 2009. Research Institute of Highway Ministry of Transport. Test methods of cement and concrete for highway engineering:JTG E30-2005[S]. Beijing:China Communication Press, 2009(in Chinese). |
| [13] | 交通运输部. 公路工程沥青及沥青混合料试验规程:JTG E20-2011[S]. 北京:人民交通出版社, 2011. Ministry of Transport of the People's Republic of China. Standard test methods of bitumen and bituminous mixtures for highway engineering:JTG E20-2011[S]. Beijing:China Communication Press, 2011(in Chinese). |
| [14] | 陈志华. 1957-2000年中国地面太阳辐射状况的研究[D]. 北京:中国科学院研究生院大气物理研究所, 2005. CHEN Zhihua. Study on surface solar radiation during 1957-2000 over China[D]. Beijing:Institute of Atmospheric Physics, Chinese Academy of Sciences, 2005(in Chinese). |
| [15] | 邓雪娇, 吴兑, 游积平. 广州市地面太阳紫外线辐射观测和初步分析[J]. 热带气象学报, 2003, 19(9):118-125. DENG Xuejiao, WU Dui, YOU Jiping. The observation of surface solar ultraviolet in Guangzhou and its preliminary analysis[J]. Journal of Tropical Meteorology, 2003, 19(9):118-125(in Chinese). |
| [16] | American Society of Testing Materials. Standard practice for operating fluorescent ultraviolet (UV) lamp apparatus for exposure of nonmetallic materials:ASTM G154-16[S]. American:ASTM, 2012. |
| [17] | 李杰, 卢朝辉, 张其云. 混凝土随机损伤本构关系——单轴受压分析[J]. 同济大学学报(自然科学版), 2003, 31(5):505-509. LI Jie, LU Zhaohui, ZHANG Qiyun. Study on stochastic damage constitutive law for concrete material subjected to uniaxial compressive stress[J]. Journal of Tongji University(Natural Science), 2003, 31(5):505-509(in Chinese). |
| [18] | HALPIN J C, KARDOS J L. The Halpin-Tsai equations:A review[J]. Polymer Engineering and Science, 1976, 16(5):344-352. |
| [19] | MALLICK P K. Fiber-reinforced composites:Materials, manufacturing and design[M]. New York:Marcel Dekker, Inc, 1993. |
| [20] | BOULEKBACHE B, HAMRAT M, CHEMROUK M, et al. Flowability of fibre-reinforced concrete and its effect on the mechanical properties of the material[J]. Construction and Building Materials, 2010, 24(9):1664-1671. |
| [21] | 李长风, 刘加平, 刘建忠, 等. 纤维增强混凝土中纤维分布表征及调控的研究进展[J]. 混凝土, 2014, 297:108-113. LI Changfeng, LIU Jiaping, LIU Jianzhong, et al. Research process of characterization and control methods of fiber distribution in fiber reinforced concrete[J]. Concrete, 2014, 297:108-113. |
| [22] | 张平, 李宇峙, 徐敏. 环氧树脂混凝土弯曲变形性能试验研究[J]. 中外公路, 2009, 29(1):208-211. ZHANG Ping, LI Yuzhi, XU Min. Experimental study on flexural deformation properties of epoxy resin concrete[J]. Journal of China and Foreign Highway, 2009, 29(1):208-211(in Chinese). |
| [23] | 李建涛, 于江, 秦拥军. 混凝土材料损伤裂纹演化过程的研究综述[J]. 混凝土与水泥制品, 2017(12):10-13. LI Jiantao, YU Jiang, Qin Yongjun. Review on the evolution process of damage cracks in concrete materials[J]. China Concrete and Cement Products, 2017(12):10-13(in Chinese). |
| [24] | 梁兴文, 胡翱翔, 于婧, 等. 钢纤维对超高性能混凝土抗弯力学性能的影响[J]. 复合材料学报, 2018, 35(3):722-731. LIANG Xingwen, HU Aoxiang, YU Jing, et al. Effect of steel fibers on the flexural response of ultra-high performance concrete[J]. Acta Materiae Compositae Sinica, 2018, 35(3):722-731(in Chinese). |
| [25] | VIPULANANDAN C, DHARMARAJAN N, CHING E. Mechanical behaviour of polymer concrete systems[J]. Materials and Structures, 1988, 21(4):268-277. |
| [26] | REIS J M L, FERREIRA A J M. Assessment of fracture properties of epoxy polymer concrete reinforced with short carbon and glass fibers[J]. Construction and Building Materials, 2004, 18(7):523-528. |
| [27] | 李国忠, 于衍真. 植物纤维增强石膏复合材料的微观结构研究[J]. 复合材料学报, 1997, 14(3):72-76. LI Guozhong, YU Yanzhen. Study on the microstructure of plant fiber reinfored gypsum composites[J]. Acta Materiae Compositae Sinica, 1997, 14(3):72-76(in Chinese). |
| [28] | LI Z, WANG X, WANG L. Properties of hemp fiber reinforced concrete composites[J]. Composites Part A:Applied Science and Manufacturing, 2006, 37(3):497-505. |
| [29] | REIS J M L. Fracture and flexural characterization of natural fiber-reinforced polymer concrete[J]. Construction and Building Materials, 2006, 20(9):673-678. |
| [30] | REIS J M L, FERREIRA A J M. Effect of marine exposure on fracture properties of epoxy concretes[J]. Polymer Testing, 2005, 24(1):121-125. |
| [31] | PICKERING K L, EFENDY M G A, LE T M. A review of recent developments in natural fiber composites and their mechanical performance[J]. Composites Part A:Applied Science and Manufacturing, 2016(83):98-112. |
| [32] | 程经纬. 环氧树脂-混凝土的冲击和老化性能研究[D]. 广州:华南理工大学, 2016. CHENG Jingwei. Study on the impact and aging properties of epoxy based concrete[D]. Guangzhou:South China University of Technology, 2016(in Chinese). |
| [33] | 李晓妮, 黄江, 刘西雷. 沥青混凝土桥面铺装使用寿命预测及常见病害处治对策[J]. 交通运输研究, 2013(18):74-77. LI Xiaoni, HUANG Jiang, LIU Xilei. Service life prediction and common disease treatment measures of asphalt concrete bridge deck pavement[J]. Transportation Standardization, 2013(18):74-77(in Chinese). |
| [34] | 陈奕惠, 粱健, 林红燕. 广州地区气温、相对湿度与医院感染的关系研究[J]. 湖北科技学院学报(医学版), 2012, 26(2):108-111. CHEN Yihui, LIANG Jian, LIN Hongyan. The relationship of air temperature, relative humidity and nosocomial infection in Guangzhou[J]. Journal of Xianning University(Medical Sciences), 2012, 26(2):108-111(in Chinese). |
| [35] | 吴安生. 混凝土试样压缩破坏机理的研究[J]. 兰州铁道学院学报(自然科学版), 2003, 22(1):24-26. WU Ansheng. Approach of concrete constriction breatngoringin[J]. Journal of Lanzhou Railway University (Natural Science), 2003, 22(1):24-26(in Chinese). |
| [36] | MA D, LIU Y, ZHANG N, et al. Micromechanical modeling of flexural strength for epoxy polymer concrete[J]. International Journal of Applied Mechanics, 2017, 9(8):117-132. |
| [37] | PHANI K K, BOSE N R. Temperature dependence of hydrothermal ageing of CSM-laminate during water immersion[J]. Composites Science and Technology, 1987, 29(2):79-87. |
| [38] | CHEN Y, DAVALOS J F, RAY I. Durability prediction for GFRP reinforcing bars using short-term data of accelerated aging tests[J]. Journal of Composites for Construction, 2006, 10(10):279-286. |
| [39] | 中交公路规划设计院有限公司. 公路水泥混凝土路面设计规范:JTG D40-2011[S]. 北京:人民交通出版社, 2011. China Communications Construction Company Highway Consultants Co. Ltd., Specifications for design of highway cement concrete pavement:JTG D40-2011[S]. Beijing:China Communication Press, 2011(in Chinese). |
