|
|
- 2018
面向组合结构刚度非线性特性的等效模型
|
Abstract:
针对组合结构轴向载荷下呈现的刚度非线性特性难以计算的问题, 提出了梁-双弹簧等效计算模型, 研究了在包含不同材料垫片的组合结构中螺栓预紧力以及部分几何尺寸对轴向刚度非线性特性的影响．结果表明：采用铝合金垫片时, 该连接组合结构的非线性特性主要表现为其轴向载荷-位移曲线在拉压状态改变时出现明显拐点; 而该结构采用石墨垫片时, 位移曲线在拉压阶段分别表现出非线性．相比于垫片厚度, 螺栓预紧力、法兰厚度以及螺栓位置对轴向拉压刚度的影响更显著, 且影响规律与所受载荷方向、垫片材料属性有关．
In the case of different axial loads，a combination structure shows its non-linear axial stiffness，which is hard to calculate. To solve this problem，an equivalent model，bending beam-double springs，was proposed. The influence of bolt pre-tightening force and geometric parameters on the non-linearity of joint axial stiffness of combination structure with different material properties of gaskets was discussed. Results indicate that when aluminum alloy gasket is used，inflection point occurs in axial load-displacement curve between the stages of stress and tension. When graphite gasket is used，displacement curve demonstrates apparent non-linear stiffness in the stages of both stress and tension. Compared with the thickness of the gasket，bolt pre-tightening force，flange thickness and position of the bolt play a more significant role on axial stiffness，and the influence law is related to loading direction and material properties of gasket
| [1] | Wang Yuanqing, Luo Ruiqi, Xiao Jianchun, et al. Experiment of welding reinforcement of end-plate connection nodes in steel-structure under loads[J]. <i>Journal of Tianjin University</i>:<i>Science and Technology</i>, 2015, 48(Suppl 1):25-31(in Chinese). |
| [2] | Zu Bingfeng, Xu Yuliang, Liu Jie, et al. Simulation on cylinder bore deformation of automotive disel engines using integral contact multi-field indirect coupling method[J]. <i>Journal of Tianjin University</i>, 2009, 42(11):1011-1016(in Chinese). |
| [3] | Lima L R O D, Freire J L D F, Vellasco P C G D S, et al. Structural assessment of minoraxis steel joints using photoelasticity and finite elements[J]. <i>Journal of Constructional Steel Research</i>, 2009, 65(2):466-478. |
| [4] | Wen Shuhua, Zhang Xueliang, Wu Meixian, et al. Fractal model of normal contact stiffness of joint interfaces and its simulation[J]. <i>Transactions of the Chinese Society for Agricultural Machinery</i>, 2009, 40(11):197-202(in Chinese). |
| [5] | Zhang Qichang, Geng Yan, Wang Chen, et al. Application of model updating to bolted joint structures[J]. <i>Journal of Tianjin University</i>:<i>Science and Technology</i>, 2014, 47(12):1095-1100(in Chinese). |
| [6] | 祖炳锋, 徐玉梁, 刘捷, 等. 车用柴油机缸孔变形整体接触多场分步耦合模拟[J]. 天津大学学报, 2009, 42(11):1011-1016. |
| [7] | Zhang Hongyan, Bai Changqing, Lin Xu, et al. Influence of non-linearity of bolted connection on dynamic characteristics of steel structure[J]. <i>Chinese Journal of Applied Mechanics</i>, 2015, 32(4):570-574(in Chinese). |
| [8] | Liu P, Zhao H, Huang K, et al. Research on normal contact stiffness of rough surface considering friction based on fractal theory[J]. <i>Applied Surface Science</i>, 2015, 349:43-48. |
| [9] | 温淑花, 张学良, 武美先, 等. 结合面法向接触刚度分形模型建立与仿真[J]. 农业机械学报, 2009, 40(11):197-202. |
| [10] | 栾宇. 航天器结构中螺栓-法兰连接的动力学建模方法研究[D]. 大连:大连理工大学机械工程学院, 2012. |
| [11] | Luan Yu. Study on Dynamic Modeling of Bolted Flange Connections in Aerospace Structures[D]. Dalian:School of Mechanical Engineering, Dalian University of Technology, 2012(in Chinese). |
| [12] | Huang Kaifang. A Thesis Submitted in Partial Fulfillment of the Requirements for the Degree of Master of Engineering[D]. Wuhan:School of Mechanical Science & Engineering, Huazhong University of Science and Technology, 2012(in Chinese). |
| [13] | 黄开放. 螺栓固定结合面动力学建模与影响因素研究[D]. 武汉:华中科技大学机械科学与工程学院, 2012. |
| [14] | 罗永峰, 王熹宇, 强旭红, 等. 高强钢在工程结构中的应用进展[J]. 天津大学学报:自然科学与工程技版, 2015, 48(增1):134-141. |
| [15] | Luo Yongfeng, Wang Xiyu, Qiang Xuhong, et al. Progress in application of high strength steel to engineering structures[J]. <i>Journal of Tianjin University</i>:<i>Science and Technology</i>, 2015, 48(Suppl 1):134-141(in Chinese). |
| [16] | 王元清, 罗睿奇, 肖建春, 等. 负载下焊接加固钢结构端板连接节点承载性能试验[J]. 天津大学学报:自然科学与工程技术版, 2015, 48(增1):25-31. |
| [17] | 张红艳, 白长青, 林旭, 等. 螺栓连接接触非线性对钢结构动力学特性的影响[J]. 应用力学学报, 2015, 32(4):570-574. |
| [18] | 温淑花, 张学良, 文晓光, 等. 结合面切向接触刚度分形模型建立与仿真[J]. 农业机械学报, 2009, 40(12):223-227. |
| [19] | Wen Shuhua, Zhang Xueliang, Wen Xiaoguang, et al. Fractal model of tangential contact stiffness of jointinterfaces and its simulation[J]. <i>Transactions of the Chinese Society for Agricultural Machinery</i>, 2009, 40(12):223-227(in Chinese). |
| [20] | Tinker M L. Nonlinearities due to joint friction and clearance in a structural dynamic test figure[C]//<i>ASME Proceedings of the Symposium on Elasto-Impact and Friction in Dynamic Systems.<i> USA, 1996, 90:35-46. |
| [21] | 张琪昌, 耿岩, 王辰, 等. 模型修正技术在螺栓连接结构中的应用探讨[J]. 天津大学学报:自然科学与工程技术版, 2014, 47(12):1095-1100. |
| [22] | Loureiro A, Gutierrez R, Reinosa J M, et al. Axial stiffness prediction of non-preloaded T-stubs:An analytical frame approach[J]. <i>Journal of Constructional Steel Research</i>, 2010, 66(12):1516-1522. |
| [23] | 侯世远. 螺纹联接松动机理研究[D]. 北京:北京理工大学机械与车辆学院, 2015. |
| [24] | Hou Shiyuan. Study on Mechanism of Loosening of Threaded[D]. Beijing:School of Mechanical Engineering, Beijing Institute of Technology, 2015(in Chinese). |
| [25] | Grosse I R, Mitchell L D. Nonlinear axial stiffness characteristics of bolted joints[J]. <i>Journal of Mechanical Design</i>, 1990, 122:442-449.</i></i> |
