|
|
- 2018
Z-pin/缝合对复合材料T型接头剪切承载能力的影响
|
Abstract:
利用三维有限元模型对Z-pin/缝合增强试验件进行有限元分析，采用内聚力模型模拟界面的破坏情况，通过在分层的上下界面加入非线性弹簧元来模拟Z-pin/缝合的增强机制，非线性弹簧元的力学性能（桥联律）由细观力学方法获得。通过与试验结果的对比发现，由于未进行界面增强的T型结构的剪切承载能力已较高，Z-pin/缝合增强较难提高T型接头的剪切承载能力。从少数几种可提高T型接头的剪切承载能力的增强方案中可看到，应选择拉伸强度较高而拉伸模量较低的缝线来进行T型接头剪切界面增强设计。 Three-dimensional FEM models were used to simulate the Z-pin/stitching reinforced T-joint specimens. The interface failure was simulated with cohesive zone model, and the effect of Z-pin/stitching was simulated with nonlinear springs inserted into the interface. The mechanical properties of the spring, i.e. bridging law, were obtained based on a micromechanical approach. Comparing with experimental results and the FEM results, it is difficult to increase the shear carrying capacity of T-joints through Z-pin/stitching as the shear carrying capacity of unreinforced T-joint is quite high already. After analyzing the a few schemes which can increase the shear carrying capacity of T-joints, choosing stitch with high tensile strength and low tensile modulus was suggested to be used for the design of interface reinforcement. 江苏高校优势学科建设工程资助项目
| [1] | EMILE G, AARON L, RICHARD B, et al. Evaluation of toughening concepts at structural features in CFRP-Part I:Stiffener pull-off[J]. Composites Part A:Applied Science & Manufacturing, 2006, 37(10):1521-1535. |
| [2] | CARTIE D D R, GIUSEPPE D A, EMILIE P, et al. 3D reinforcement of stiffener-to-skin T-joints by Z-pinning and tufting[J]. Engineering Fracture Mechanics, 2006, 73(16):2532-2540. |
| [3] | 朱华东, 矫桂琼, 杨宝宁. 缝合复合材料Ⅱ型断裂特性研究[J], 复合材料学报, 2001, 18(5):85-89. ZHU Huadong, JIAO Guiqiong, YANG Baoning. Investigation into the effect of stitching in CFRP on mode Ⅱ delamination toughness[J]. Acta Materiae Compositae Sinica, 2001, 18(5):85-89(in Chinese). |
| [4] | 毛春见, 许希武, 郑达. 缝合复合材料层板低速冲击及冲击后压缩实验研究[J]. 复合材料学报, 2012, 29(2):160-166. MAO Chunjian, XU Xiwu, ZHENG Da. Experimental investigation of stitched laminates subjected to low-velocity impact and compression after impact[J]. Acta Materiae Compositae Sinica, 2012, 29(2):160-166(in Chinese). |
| [5] | GRASSI M, ZHANG X. Finite element analyses of mode I interlaminar delamination in z-fiber reinforced composite laminates[J]. Composites Science and Technology, 2003, 63(12):1815-1832. |
| [6] | GLAESSGEN E H, RAJU I S, POE C C. Delamination and stitched failure in stitched composite joints[C]. 40th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference and Exhibit,Saint Louis:AIAA, 1999. |
| [7] | ADAMS D O. Stitch compliance in delaminated composites[C]. 29th SAMPLE Technical Conference. Covina:SAMPE, 1997:601-613. |
| [8] | IWAHORI Y. Mechanism of interlaminar strength improvement for CFRP laminates by stitching[C]. 24th International SAMPLE Europe Conference. Paris:SAMPE, 2005:5-7. |
| [9] | 段沐枫, 李宁, 郑莹莹, 等. K-cor夹层结构制备工艺[J]. 宇航材料工艺, 2012(5):21-25. DUAN Mufeng, LI Ning, ZHENG Yingying, et al. Manufacturing processes of k-cor sandwich structure[J]. Aerospace Materials and Technology, 2012(5):21-25(in Chinese). |
| [10] | 李梦佳, 陈普会, 孔斌, 等. Z-pin参数对复合材料T型接头拉脱承载能力的影响[J]. 复合材料学报, 2015, 32(2):571-578. LI Mengjia, CHEN Puhui, KONG Bin, et al. Effect of Z-pin parameters on pull-off carrying capacity of composite T-joints[J]. Acta Materiae Compositae Sinica, 2015, 32(2):571-578(in Chinese). |
| [11] | 李梦佳, 陈普会, 孔斌, 等. 缝合参数对复合材料T型接头拉脱承载能力的影响[J]. 复合材料学报, 2016, 33(3):681-688. LI Mengjia, CHEN Puhui, KONG Bin, et al. Effects of parameters of stitching on the pull-off carrying capacity of composite T-joints[J]. Acta Materiae Compositae Sinica, 2016, 33(3):681-688(in Chinese). |
| [12] | 李梦佳, 陈普会, 孔斌, 等. T型接头蒙皮厚度对Z-pin增强效果的影响[J]. 复合材料学报, 2016, 33(7):1461-1467. LI Mengjia, CHEN Puhui, KONG Bin, et al. Influence of skin thickness of T-joint on the reinforcing effect of Z-pin[J]. Acta Materiae Compositae Sinica, 2016, 33(7):1461-1467(in Chinese). |
| [13] | STICKLER P B, RAMULU M. Parametric analyses of stitched composite T-joints by the finite element method[J]. Materials and Design, 2002, 23(8):751-758. |
| [14] | 叶强. 层合复合材料的粘聚区模型及其应用研究[D]. 南京:南京航空航天大学, 2012. YE Qiang. Research on cohesive zone model of laminated composites and its applications[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2012(in Chinese). |
| [15] | 张向阳, 李勇, 褚奇奕, 等. Z-pin点阵分布对层合板面内压缩性能的影响[J]. 航空学报, 2014, 35(1):195-202. ZHANG Xiangyang, LI Yong, CHU Qiyi, et al. Influence of Z-pins insertion pattern on in-plane compression properties of laminates[J]. Acta Aeronautica et Astronautica Sinica, 2014, 35(1):195-202(in Chinese). |
| [16] | 郑锡涛, 李泽江, 杨帆. Z-pin增强复合材料层合板断裂韧性试验研究[J]. 复合材料学报, 2010, 27(4):180-188. ZHENG Xitao, LI Zejiang, YANG Fan. Experimental investigation on the fracture toughness of Z-pins reinforced composite laminates[J]. Acta Materiae Composite Sinica, 2010, 27(4):180-188(in Chinese). |
| [17] | 刘兵山, 燕瑛. 缝合复合材料弹性性能分析的新方法——流场模型Ⅱ:缝合层合板弹性常数计算与实验[J]. 复合材料学报, 2006, 23(4):136-142. LIU Bingshan, YAN Ying. New method on the elastic properties of stitched composites-Flow field model Ⅱ:Elastic constants calculation and tests of stitched laminates[J]. Acta Materiae Compositae Sinica, 2006, 23(4):136-142(in Chinese). |
| [18] | 张涛涛, 周洪, 史文华, 等. Z-pin植入对二维机织复合材料层合板力学性能影响的数值模拟[J]. 复合材料学报, 2014, 31(2):295-303. ZHANG Taotao, ZHOU Hong, SHI Wenhua, et al. Numerical simulation of the Z-pin inserting effect on mechanical properties of 2D woven composite laminate[J]. Acta Materiae Compositae Sinica, 2014, 31(2):295-303(in Chinese). |
| [19] | 刘兵山, 燕瑛. 缝合复合材料弹性性能分析的新方法——流场模型I:缝合单层板弹性常数计算[J]. 复合材料学报, 2006, 23(4):129-135. LIU Bingshan, YAN Ying. New method on the elastic properties of stitched composites-Flow field model I:Elastic constants calculation of the stitched laminar[J]. Acta Materiae Compositae Sinica, 2006, 23(4):129-135(in Chinese). |
| [20] | JAIN J K, DRANSFIELD K A, MAI Y W. On the effects of stitching in CFRPs-Ⅰ. mode Ⅰ delamination toughness[J]. Composites Science and Technology, 1998, 58(6):815-827. |
| [21] | 李成虎, 燕瑛. Z-pin增强复合材料T型接头层间性能的建模与分析[J]. 复合材料学报, 2010, 27(6):152-157. LI Chenghu, YAN Ying. Modeling and analysis of Z-pin reinforcing in through-thickness direction of composite T-joint[J]. Acta Materiae Composite Sinica, 2010, 27(6):152-157(in Chinese). |
