|
|
- 2017
考虑弹性支撑时蜂窝芯剪切屈曲强度的插值求解方法
|
Abstract:
结合最小余能原理和薄板剪切屈曲失稳理论，给出了蜂窝芯等效剪切屈曲强度的理论表达式。将胞壁等效为受弹性支撑的梁，通过对固支和简支条件下的屈曲强度进行插值求解实际胞壁间为弹性支撑时的剪切屈曲强度。然后，利用三点短梁弯曲试验测量常用Nomex蜂窝芯的剪切屈曲强度，并与弹性支撑下的理论解进行对比，试验结果与理论解吻合较好，验证了理论方法的有效性。最后，讨论了剪切屈曲强度的各向异性及蜂窝高度对剪切屈曲强度的影响。结果表明，剪切屈曲强度的各向异性程度与蜂窝高度无关，但随着蜂窝高度的增加，蜂窝芯的纵向和横向剪切屈曲强度均逐渐减少，减小幅度逐渐减缓。 The theoretical form of shear buckling strength of honeycomb core was shown based on the principle of minimum complementary energy and shear buckling theory of thin plate. By regarding the cell wall as a beam with elastic supports, the shear buckling strength of honeycomb core considering elastic supports was got from interpolating the strengths of clamped and simple supports. Then, three point short beam bending tests were performed to obtain shear buckling strength of Nomex honeycomb core. The tests' results were compared with theoretical results and agree well with theoretical solutions, which verified our theory. Finally, the anisotropy of shear buckling strength and the influence of honeycomb height on shear buckling strength were investigated. The results show that there is no influence of honeycomb height on the anisotropy of shear buckling strength, while both the longitudinal and transverse shear buckling strengths decrease with the increasing height of honeycomb and the decreasing ratio drops gradually. 西北工业大学研究生创意创新种子基金（Z2015046）
| [1] | ZHANG D, JIANG D, FEI Q, et al. Experimental and numerical investigation on indentation and energy absorption of a honeycomb sandwich panel under low-velocity impact[J]. Finite Elements in Analysis & Design, 2016, 117-118: 21-30. |
| [2] | CRICRì G, PERRELLA M, CALì C. Honeycomb failure processes under in-plane loading[J]. Composites Part B: Engineering, 2013, 45(1): 1079-1090. |
| [3] | 富明慧, 徐欧腾, 陈誉.蜂窝芯层等效参数研究综述[J].材料导报, 2015, 29(5): 127-134. FU M H, XU O T, CHEN Y.An overview of equivalent parameters of honeycomb cores[J].Materials Review, 2015, 29(5): 127-134 (in Chinese). |
| [4] | 郑吉良, 孙勇, 彭明军.等腰梯形蜂窝芯玻璃钢夹芯板的面内压缩性能[J]. 复合材料学报, 2016, 33(2): 408-417. ZHENG J L, SUN Y, PENG M J.In-plane compressive properties for isosceles-trapezoid honeycomb core of glass steel sandwich panel[J]. Acta Materiae Compositae Sinica, 2016, 33(2): 408-417 (in Chinese). |
| [5] | ROARK R J, SADEGH A M. Roark's formulas for stress and strain[M]. USA: McGraw-Hill, 2012. |
| [6] | 周祝林.蜂窝芯子剪切强度研究[J].纤维复合材料, 1998(3): 13-17. ZHOU Z L.Study on shear strength of honeycomb core[J].Fiber Composites, 1998(3): 13-17 (in Chinese). |
| [7] | LEE H S, HONG S H, LEE J R, et al. Mechanical behavior and failure process during compressive and shear deformation of honeycomb composite at elevated temperatures[J]. Journal of Materials Science, 2002, 37(6): 1265-1272. |
| [8] | PAN S D, WU L Z, SUN Y G, et al. Longitudinal shear strength and failure process of honeycomb cores[J]. Compo-site Structures, 2006, 72(1): 42-46. |
| [9] | PAN S D, WU L Z, SUN Y G. Transverse shear modulus and strength of honeycomb cores[J]. Composite Structures, 2008, 84(4): 369-374. |
| [10] | 泮世东, 冯吉才, 吴林志.蜂窝芯子纵向等效剪切性能分析[C]//中国力学学会2009学术大会论文集, 2009: 1-8. PAN S D, FENG J C, WU L Z.Longitudinal shear properties of honeycomb cores[C]//Proceeding of CCTAM, 2009: 1-8 (in Chinese). |
| [11] | JEYAKRISHNAN P R, CHOCKALINGAM K K S K, NARAYANASAMY R. Studies on buckling behavior of honeycomb sandwich panel[J]. International Journal of Advanced Manufacturing Technology, 2013, 65(5-8): 803-815. |
| [12] | JIMénez F L, TRIANTAFYLLIDIS N. Buckling of rectangular and hexagonal honeycomb under combined axial compression and transverse shear[J]. International Journal of Solids & Structures, 2013, 50(24): 3934-3946. |
| [13] | SHI G, TONG P. Local buckling of honeycomb sandwich plates under action of transverse shear forces[J]. Aiaa Journal, 1994, 32(7): 1520-1524. |
| [14] | ASTM. Standard test method core shear properties of sandwich constructions by beam flexure: ASTM C393/C 393M—06[S]. USA: ASTM, 2006. |
| [15] | FOO C C, CHAI G B, SEAH L K. Mechanical properties of Nomex material and Nomex honeycomb structure[J]. Composite Structures, 2007, 80(4): 588-594. |
| [16] | 杨亚政, 杨嘉陵, 曾涛, 等. 轻质多孔材料研究进展[J].力学季刊, 2007, 28(4): 503-516. YANG Y Z, YANG J L, ZENG T, et al. Progress in Research work of light materials[J].Chinese Quarterly of Mechanics, 2007, 28(4): 503-516 (in Chinese). |
| [17] | LIU L, WANG H, GUAN Z. Experimental and numerical study on the mechanical response of Nomex honeycomb core under transverse loading[J]. Composite Structures, 2015, 121: 304-314. |
| [18] | 徐胜今, 孔宪仁, 王本利, 等.正交异性蜂窝夹层板动、静力学问题的等效分析方法[J]. 复合材料学报, 2000, 17(3): 92-95. XU S J, KONG X R, WANG B L, et al. Method of equivalent analysis for statics and dynamics behavior of orthotropic honeycomb sandwich plates[M]. Acta Materiae Compositae Sinica, 2000, 17(3): 92-95 (in Chinese). |
| [19] | GIBSON L J, ASHBY M F. Cellular solids: Structure and properties[M]. UK: Cambridge University Press, 1988. |
| [20] | 富明慧, 徐欧腾.关于蜂窝芯体面外等效剪切模量的讨论[J].固体力学学报, 2014(4): 334-340. FU M H, XU O T, Discussion on equivalent transverse shear modulus of honeycomb cores[J]. Chinese Journal of Solid Mechanics, 2014(4): 334-340 (in Chinese). |
| [21] | 王博, 陈友伟, 石云峰.多层级蜂窝材料的面内模量缺陷敏感性[J]. 复合材料学报, 2014, 31(2): 495-504. WANG B, CHEN Y W, SHI Y F. Imperfection sensitivities of in-plane moduli of hierarchical lattice materials to cell edge waviness[J]. Acta Materiae Compositae Sinica, 2014, 31(2): 495-504 (in Chinese). |
| [22] | MUKHOPADHYAY T, ADHIKARI S. Equivalent in-plane elastic properties of irregular honeycombs: An analytical approach[J]. International Journal of Solids & Structures, 2016, 91: 169-184. |
| [23] | TIMOSHENKO S P, GERE J M, PRAGER W. Theory of elastic stability[M]. USA: McGraw-Hill, 1936 |
| [24] | ZHANG J, ASHBY M F. The out-of-plane properties of honeycombs[J]. International Journal of Mechanical Sciences, 1992, 34(6): 475-489. |
| [25] | 刘念超.蜂窝芯子的力学性能计算[J].玻璃钢/复合材料, 1993(6): 21-24. LIU L C. Mechanical property calculation of honeycomb core[J]. Fiber Reinforced Plastics/Composites, 1993(6): 21-24 (in Chinese). |
