|
|
- 2018
微注射成型高密度聚乙烯-线性低密度聚乙烯共混物的微结构及力学性能
|
Abstract:
为提高线性低密度聚乙烯（LLDPE）的拉伸强度和模量，扩大其应用领域，将三种不同相对分子质量的高密度聚乙烯（HDPE）分别与LLDPE共混，通过微注射成型技术制备HDPE-LLDPE制品。综合利用DSC、广角X射线衍射（WAXD）、小角X射线散射（SAXS）和拉伸性能测试研究了共混物在微注射成型过程中的结构演化及力学性能。拉伸测试结果表明，与纯LLDPE相比，HDPE-LLDPE的拉伸强度和模量随HDPE分子量的增加而增加。微结构分析结果显示，随HDPE分子量的增加，HDPE-LLDPE制品的分子链和片晶取向度增大、结晶度增加，且制品内形成了较多取向的Shish-Kebab晶体结构。通过分析微结构的表征结果，解释了HDPE-LLDPE的拉伸强度和模量显著提高的原因。 The high density polyethylene (HDPE) with three different molecular weight were blended with linear low density polyethylene (LLDPE) to improve the tensile strength and modulus of LLDPE and expand its application field, and then molded by micro-injection molding to prepare HDPE-LLDPE parts. A combination of DSC, wide-angle X-ray diffraction (WAXD), small angle X-ray scattering (SAXS) and tensile test were performed to provide a comprehensive analysis of microstructure variations and mechanical properties. The tensile test indicates that the tensile strength and modulus of micro-injection molded HDPE-LLDPE parts are enhanced compared with the pure LLDPE. The microstructure characterizations show that the macromolecular and lamellar orientation degree and crystallinity of HDPE-LLDPE increase with increasing molecular weight of HDPE and more highly oriented structure, Shish-Kebab, is formed in HDPE-LLDPE composites. The reasons for considerably enhanced tensile strength and modulus are elucidated based on the analysis of microstructural results. 国家自然科学基金（51173171）；河南工程学院博士基金（D2015018）
| [1] | YANG J H, WANG K, DENG H, et al. Hierarchical structure of injection molded bars of HDPE/MWCNTs composites with novel nanohybrid shish-kebab[J]. Polymer, 2010, 51(3):774-782. |
| [2] | SHI S Y, WANG L N, XIN C Z, et al. Special morphology and its role in mechanical enhancement of LLDPE/MWCNTs composites prepared by hot compression molding[J]. Journal of Applied Polymer Science, 2017, 134(48):45525-45532. |
| [3] | YANG J H, WANG C Y, WANG K, et al. Direct formation of nanohybrid shish-kebab in the injection molded bar of polyethylene/multiwalled carbon nanotubes composite[J]. Macromolecules, 2009, 42(18):7016-7023. |
| [4] | LIANG S, WANG K, TANG C Y, et al. Unexpected molecular weight dependence of shish-kebab structure in the oriented linear low density polyethylene/high density polyethylene blends[J]. The Journal of Chemical Physics, 2008, 128(17):174902-174910. |
| [5] | LIANG S, WANG K, CHEN D Q, et al. Crystal morphology and tensile properties of LLDPE containing PP fibers as obtained via dynamic packing injection molding[J]. Polymer, 2006, 47(20):7115-7122. |
| [6] | SHI S Y, PAN Y M, LU B, et al. Realizing the simultaneously improved toughness and strength of ultra-thin LLDPE parts through annealing[J]. Polymer, 2013, 54(25):6843-6852. |
| [7] | 石素宇, 王利娜, 赵康, 等. 再生PET纤维/PP复合材料的结构及力学性能[J]. 复合材料学报, 2017, 34(7):1511-1516. SHI S Y, WANG L N, ZHAO K, et al. The structure and mechanical property of recycled PET fiber/PP composite[J]. Acta Materiae Compositae Sinica, 2017, 34(7):1511-1516(in Chinese). |
| [8] | LIN X, CATON-ROSE F, REN D Y, et al. Shear-induced crystallization morphology and mechanical property of high density polyethylene in micro-injection molding[J]. Journal of Polymer Research, 2013, 20(122):1-12. |
| [9] | FRICK A, STERN C, MICHLER G, et al. Study on flow induced nano structures in iPP with different molecular weight and resulting strength behavior[J]. Macromolecular Symposia, 2010, 294(1):91-101. |
| [10] | LIU X H, ZHENG G Q, DAI K, et al. Morphological comparison of isotactic polypropylene molded by water-assisted and conventional injection molding[J]. Journal of Materials Science, 2011, 46(24):7830-7838. |
| [11] | JI C Q, XIE M C, CHANG B B, et al. β-crystal in injection moulded poly(ethylene terephthalate) fibre/isotactic polypropylene composite[J]. Composites Part A:Applied Science and Manufacturing, 2013, 46:26-33. |
| [12] | ZHENG G Q, JIA Z H, LIU X H, et al. Enhanced orientation of the water-assisted injection molded iPP in the presence of nucleating agent[J]. Polymer Engineering and Science, 2012, 52(4):725-732. |
| [13] | SOMANI R H, YANG L, HSIAO B S, et al. Shear-induced molecular orientation and crystallization in isotactic polypropylene:Effects of the deformation rate and strain[J]. Macromolecules, 2005, 38(4):1244-1255. |
| [14] | SEKI M, THURMAN D W, OBERHAUSER J P, et al. Shear-mediated crystallization of isotactic polypropylene:The role of long chain-long chain overlap[J]. Macromolecules, 2002, 35(7):2583-2594. |
| [15] | KIMATA S, SAKURAI T, NOZUE Y, et al. Molecular basis of the shish-kebab morphology in polymer crystallization[J]. Science, 2007, 316(5827):1014-1017. |
| [16] | WANG Y, ZOU H, FU Q, et al. Super polyolefin blends achieved via dynamic packing injection molding:tensile strength[J]. Journal of Applied Polymer Science, 2002, 85(2):236-243. |
| [17] | LIU S Y, LIANG Y Y, QUAN Y B, et al. Electrospun isotactic polypropylene fibers:Self-similar morphology and microstructure[J]. Polymer, 2013, 54(12):3117-3123. |
| [18] | GAO J, ZHANG Q, WANG K, et al. Effect of shearing on the orientation, crystallization and mechanical properties of HDPE/attapulgite nanocomposites[J]. Composites Part A, 2012, 43(4):562-569. |
| [19] | ZHANG G, JIANG L, SHEN K Z, et al. Self-reinforcement of high-density polyethylene/low-density polyethylene prepared by oscillating packing injection molding under low pressure[J]. Journal of Applied Polymer Science, 1999, 71(5):799-804. |
| [20] | MALHAB N B, REGNIER G. Influence of the microinjection moulding process on the crystalline orientation and morphology of semicrystalline polymers[J]. AIP Conference Proceedings, 2011, 1353:820-825. |
| [21] | FUJIYAMA M, WAKINO T, KAWASAKI Y. Structure of skin layer in injection-molded polypropylene[J]. Journal of Applied Polymer Science, 1988, 35(1):29-49. |
| [22] | GUAN Q, ZHU X G, CHIU D. Self-reinforcement of polypropylene by oscillating packing injection molding under low pressure[J]. Journal of Applied Polymer Science, 1996, 62(5):755-762. |
| [23] | KALAY G, BEVIS M J. Processing and physical property relationships in injection-molded isotactic polypropylene 1:mechanical properties[J]. Journal of Polymer Science, Part B:Polymer Physics, 1997, 35(2):241-263. |
| [24] | PAN Y M, SHI S Y, XU W Z, et al. Wide distribution of shish-kebab structure and tensile property of microinjection molded isotactic polypropylene microparts:A comparative study with injection-molded macroparts[J]. Journal of Materials Science, 2014, 49(3):1041-1048. |
