|
|
- 2017
三种耐热剂对全氟聚醚橡胶材料耐热性能的影响
|
Abstract:
研究了碳纳米管（CNTs）、有机蒙脱土（OMMT）、Fe2O3对全氟聚醚（PFPE）橡胶力学性能、压缩永久变形、热稳定性及耐热空气老化性能的影响；采用热分解动力学模型分析了未添加耐热剂的PFPE橡胶的热降解机制。结果表明：CNTs、OMMT、Fe2O3均能提高PFPE橡胶基体的热稳定性，其中，CNTs/PFPE橡胶复合材料起始热失重温度及失重5%时的温度相比未添加耐热剂的PFPE橡胶分别提高了32.1℃和29.0℃；Fe2O3能明显稳定PFPE橡胶基体在200℃热空气条件下老化72 h后的性能。在空气及N2气氛下，随着升温速率的提高，未添加耐热剂的PFPE橡胶的热失重曲线均向高温方向移动。根据Kissinger方程，计算出PFPE橡胶基体在空气气氛下的热解活化能为135.06 kJ/mol，在N2气氛下的热解活化能为262.46 kJ/mol。 The effect of carbon nanotubes (CNTs), organic montmorillonite (OMMT), and Fe2O3 on the mechanical properties, thermal stability and hot aging resistance of perfluoropolyether (PFPE) rubbers were investigated. The thermal pyrolysis behaviors of pure PFPE rubber were analyzed by thermal decomposes method. The results indicate that dramatic increases in thermal stability are observed through the joined CNTs, OMMT and Fe2O3. Compared to pure PFPE rubber, the initial decomposition temperature and the 5% mass loss temperature of CNTs/PFPE rubber composite are 32.1℃ and 29.0℃ higher, respectively. The properties of Fe2O3/PFPE rubber composite after ageing at 200℃×72 h are obviously stabilized. The thermogravimetry and differential thermogravimetry curves of pure PFPE rubber move toward to high temperatures with increasing heating rate in air and N2. According to the Kissinger basic formula, the so-called activation energy of pure PFPE rubber is calculated to be 135.06 kJ/mol and 262.46 kJ/mol in air and N2, respectively.
| [1] | 赵明强, 李辉, 张炉青, 等. 全氟聚醚的研究进展[J]. 山东化工, 2009, 38(4): 25-27. ZHAO M Q, LI H, ZHANG L Q, et al. Study progress in perfluoropolyether[J]. Shandong Chemical Industry, 2009, 38(4): 25-27 (in Chinese). |
| [2] | 梁小松, 赵维鹏. 全氟聚醚-水界面上的氟表面活性剂[J]. 有机氟工业, 2000(1): 38-44 (译文). LIANG X S, ZHAO W P. Perfluorinated surfactants at the perfluoropolyether-water interface[J]. Organo-Fluorine Industry, 2000(1): 38-44 (Translation) (in Chinese). |
| [3] | 巫金东, 刘凤英. 全氟聚醚橡胶的性能研究[J]. 宇航材料工艺, 1988(1): 40-44+68. WU J D, LIU F Y. Study on properties of perfluoropolyether rubber[J]. Aerospace Materials & Technology, 1988(1): 40-44+68 (in Chinese). |
| [4] | XIAO Z B, GUO M M, GUO R K, et al. Thermal stability, decomposition kinetics and storage time of gutta-percha[J]. Chemistry and Industry of Forest Products, 2013, 33(6): 7-13. |
| [5] | 蔡仁钦, 彭涛, 王凤德, 等. 芳纶Ⅱ与芳纶Ⅲ的热分解行为比较[J]. 合成纤维工业, 2010, 33(4): 14-17. CAI R Q, PENG T, WANG F D, et al. Comparison of thermal decomposition behavior of aramid fibers Ⅱ and Ⅲ[J]. China Synthetic Fiber Industry, 2010, 33(4): 14-17 (in Chinese). |
| [6] | 中国国家标准化管理委员会. 硫化橡胶或热塑性橡胶 拉伸应力应变性能的测定:GB/T 528―2009[S]. 北京: 中国标准出版社, 2009. Standardization Administration of the People's Republic of China. Rubber, vulcanized or thermoplastic: Determination of tensile stress-strain properties: GB/T 528―2009[S]. Beijing: China Standards Press, 2009 (in Chinese). |
| [7] | KISSINGER H E. Reaction kinetics in differential thermal analysis[J]. Analytical Chemistry, 1957, 29(11): 1702-1706. |
| [8] | 曾秀妮, 段跃新. 840S环氧树脂体系固化反应特性[J]. 复合材料学报, 2007, 24(3): 100-104. ZENG X N, DUAN Y X. Curing reaction characteristics of 840S epoxy resin[J]. Acta Materiae Compositae Sinica, 2007, 24(3): 100-104 (in Chinese). |
| [9] | 隋刚, 杨小平, 梁吉, 等. 碳纳米管/天然橡胶复合材料的制备及性能[J]. 复合材料学报, 2005, 22(5): 72-77. SUI G, YANG X P, LIANG J, et al. Preparation and properties of carbon nanotubers/natural rubber composites[J]. Acta Materiae Compositae Sinica, 2005, 22(5): 72-77 (in Chinese). |
| [10] | 李爱玲, 熊金平, 左禹, 等. 聚氨酯胶粘剂的热分解动力学研究[J]. 物理化学学报, 2007, 23(10): 1622-1626. LI A L, XIONG J P, ZUO Y, et al. Thermal decomposition kinetics of polyurethane adhesive[J]. Acta Physico-Chimica Sinica, 2007, 23(10): 1622-1626 (in Chinese). |
| [11] | 张美云, 王茹楠, 陆赵情, 等. 对位芳纶纸热稳定性及其热分解动力学研究[J]. 中国造纸, 2016, 35(5): 6-10. ZHANG M Y, WANG R N, LU Z Q, et al. Study on the thermal stability and thermal decomposition kinetics of para-aramid paper based composite[J]. China Pulp & Paper, 2016, 35(5): 6-10 (in Chinese). |
| [12] | 于佳, 张博明, 王殿富, 等. 典型双马来酰亚胺数值固化动力学模型的研究[J]. 复合材料学报, 2004, 21(1): 78-83. YU J, ZHANG B M, WANG D F, et al. Study of cure kinetic model of typical bismelemide[J]. Acta Materiae Compositae Sinica, 2004, 21(1): 78-83 (in Chinese). |
| [13] | 中国国家标准化管理委员会. 硫化橡胶或热塑性橡胶压入硬度试验方法 邵氏硬度计法(邵尔硬度): GB/T 531.1—2008[S]. 北京: 中国标准出版社, 2008. Standardization Administration of the People's Republic of China. Rubber, vulcanized or thermoplastic: Determination of indentation hardness-Part I: Duromerer method (Shore hardness): GB/T 531.1—2008[S]. Beijing: China Standards Press, 2008 (in Chinese). |
| [14] | 中国国家标准化管理委员会. 硫化橡胶、热塑性橡胶 常温、高温和低温下压缩永久变形测定:GB/T 7759—1996[S]. 北京: 中国标准出版社, 1996. Standardization Administration of the People's Republic of China. Rubber, vulcanized or thermoplastic: Determination of compression set at ambient elevated or low temperatures: GB/T 7759—1996[S]. Beijing: China Standards Press, 1997 (in Chinese). |
| [15] | 苏正涛, 米志安, 王景鹤. 金属氧化物对共聚氟硅橡胶耐热性能的影响[J]. 有机硅材料, 2004, 18(1): 13-14. SU Z T, MI Z, WANG J H. Effects on the heat resistant properties of copolymerized fluorosilicone rubber to metal oxide[J]. Silicone Material, 2004, 18(1): 13-14 (in Chinese). |
| [16] | 卿凤翎. 高性能含氟聚合物研究应用进展[J]. 宇航材料工艺, 2013, 43(1): 11-14. QING F L. Recent advances of fluorinated polymers[J]. Aerospace Materials & Technology, 2013, 43(1): 11-14 (in Chinese). |
| [17] | 许志国, 张永华. 全氟聚醚的制备与应用[J]. 辽宁化工, 2007, 36(4): 257-259. XU Z G, ZHANG Y H. Preparation and application of perfluoro-polyether[J]. Liaoning Chemical Industry, 2007, 36(4): 257-259 (in Chinese). |
| [18] | MOTOO F, MASAAKI Y, AKIRA Y, et al. Perfluoropolyether rubber composition and ion-conducting polymer electrolyte membrane: US Patent, 7838616[P]. 2010-11-23. |
| [19] | 栗付平, 边俊峰, 张洪雁. 金属(氢)氧化物对氟醚橡胶耐热老化性能的影响[J]. 橡胶工业, 1998, 45(5): 281-283. LI F P, BIAN J F, ZHANG H Y. Effect of metal oxides on thermal stability of fluoroether elastomer[J]. China Rubber Industry, 1998, 45(5): 281-283 (in Chinese). |
| [20] | 李辉, 诸国红, 施强, 等. 硫酸钙晶须改性氟橡胶复合材料的热稳定性[J]. 复合材料学报, 2011, 28(4): 58-62. LI H, ZHU G H, SHI Q, et al. Thermal stability of calcium sulfate whisker modified fluororubber composites[J]. Acta Materiae Compositae Sinica, 2011, 28(4): 58-62 (in Chinese). |
| [21] | 鲜一, 张友捷, 伍勇. 氟橡胶热分解动力学及热老化寿命研究[J]. 四川化工, 2016, 19(1): 13-16. XIAN Y, ZHANG Y J, WU Y. Study on thermal decomposition dynamics and ageing of fluororubber[J]. Sichuan Chemical Industry, 2016, 19(1): 13-16 (in Chinese). |
| [22] | SHEN Y X, ZHAN M S, WANG K, et al. The pyrolysisi behaviors of polyimide foam derived from 3, 3', 4, 4'-benzophenone tetracarboxylic dianhydrede/4, 4'-oxydianiline[J]. Journal of Applied Polymer Science, 2010, 115(3): 1680-1687. |
| [23] | 李伟东, 张金栋, 刘刚, 等. 高韧性双马来酰亚胺树脂的固化反应动力学和TTT图[J]. 复合材料学报, 2016, 33(7): 1475-1483. LI W D, ZHANG J D, LIU G, et al. Curing reaction kinetics and TTT diagram of high toughness bismaleimide resin[J]. Acta Materiae Compositae Sinica, 2016, 33(7): 1475-1483 (in Chinese). |
