|
|
- 2016
聚乙二醇对环氧胶衣温度冲击开裂性能的影响
|
Abstract:
为开发一种满足航空环境要求的新型环氧胶衣,首先,研究了不同分子量、不同含量的聚乙二醇(PEG)改性环氧胶衣在室温下的冲击韧性及冲击断面形貌;然后,采用一种简单温度冲击试样模型,着重研究了PEG改性环氧胶衣在温度冲击(-50℃/30 min+90℃/30 min)下的开裂性能,并通过分析热膨胀及储能模量等的变化趋势对其进行了验证。结果表明:5wt% PEG-1000改性环氧胶衣的冲击强度比未改性环氧胶衣的提高了31.8%,达到最高值4.97 kJ·m-2;PEG-1000和PEG-2000改性环氧胶衣的冲击断面呈现出更明显的塑性变形形貌,胶衣的冲击韧性得到提高;15wt% PEG-400改性环氧胶衣在温度冲击下的宏观初始开裂性能达到最佳,平均初始开裂需要进行10.4次循环;改性环氧胶衣的耐开裂扩散性能基本上随着PEG分子量和含量的增加而提高,但裂纹宽度也会随PEG分子量的增加而扩大。 In order to develop a new type epoxy gel coat to meet the requirements of aeronautical environment, the impact toughness and impact fracture morphologies of epoxy gel coats modified with different molecular weights and different amounts of polyethylene glycol(PEG) at room temperature were investigated. Then, the crack properties of PEG modified epoxy gel coat under thermal shock(-50℃/30 min+90℃/30 min) were mainly investigated by using a simple thermal shock specimen model, and it was verified by analyzing the changing tendencies of thermal expansion and storage modulus etc. The results show that the impact strength of 5wt% PEG-1000 modified epoxy gel coat is enhanced by 31.8% comparing with that of unmodified epoxy gel coat, which reaches the highest value of 4.97 kJ·m-2. More obvious plastic deformation morphologies appear on the impact fracture surfaces of PEG-1000 and PEG-2000 modified epoxy gel coats, and the impact toughness of gel coats increases. The macroscopic initial crack property of 15wt% PEG-400 modified epoxy gel coat under thermal shock reaches the best, average initial crack needs conducting 10.4 cycles. The properties of crack extension resistance for modified epoxy gel coat are basically improved with the increase of PEG molecular weight and content. However, the crack width will be amplified with the increase of PEG molecular weight.
| [1] | 马立敏, 张嘉振, 岳广全, 等. 复合材料在新一代大型民用飞机上的应用[J]. 复合材料学报, 2015, 32(2):317-322. MA L M, ZHANG J Z, YUE G Q, et al. Application of composites in large commercial aircraft[J]. Acta Materiae Compositae Sinica, 2015, 32(2):317-322(in Chinese). |
| [2] | WEHNER J. Two-component composition for producing polyurethane gel coats for epoxy-resin and vinyl-esther resin composite materials:US20060287463[P]. 2006-12-21. |
| [3] | ARCHIE W, BRAIN A, THOMAS J, et al. Urethane acrylate gel coat resin and method of making:US20060167208[P]. 2006-07-27. |
| [4] | TOTH J, ROMAINE M. New gel coat formulation:US20110123750[P]. 2011-05-26. |
| [5] | ZHAO M Y, HUS C P, BAUCHET F, et al. Low VOC thermmosetting polyester acrylic resin for gel coat:US8546486[P]. 2013-10-01. |
| [6] | CHU X, HUANG R, YANG H, et al. The cryogenic thermal expansion and mechanical properties of plasma modified ZrW2O8 reinforced epoxy[J]. Materials Science and Engineering:A, 2011, 528(9):3367-3374. |
| [7] | 李芝华, 谢科予. 环氧灌封料低温开裂问题及对策研究进展[J]. 材料导报, 2006, 20(8):41-43. LI Z H, XIE K Y. Progress in study on crack initiation in epoxy resin sealing compounds at low temperature and its measures[J]. Material Review, 2006, 20(8):41-43(in Chinese). |
| [8] | TRAPPE V, GVNZEL S, JAUNICH M. Correlation between crack propagation rate and cure process of epoxy resins[J]. Polymer Testing, 2012, 31(5):654-659. |
| [9] | HU J, YANG B, JIN F L, et al. Fracture toughness and surface morphology of polysulfone-modified epoxy resin[J]. Journal of Industrial and Engineering Chemistry, 2014, 25:9-11. |
| [10] | GUO H, SREEKUMAR T V, LIU T, et al. Structure and properties of ploycrylonitrile/single wall carbon nanotube composite films[J]. Polymer, 2005, 46(9):3001-3005. |
| [11] | NISHIJIMA S, HONDA Y, OKADA T. Application of the positron annihilation method for evaluation of organic materials for cryogenic use[J]. Cryogenic, 1995, 35(11):779-781. |
| [12] | LIU Y, YANG G, XIAO H M, et al. Mechanical properties of cryogenic epoxy adhesives:Effects of mixed curing agent content[J]. International Journal of Adhesion and Adhesives, 2013, 41:113-118. |
| [13] | FINDIK F, YILMAZ R, K？KSAL T. Investigation of mechanical and physical properties of several industrial rubbers[J]. Materials & Design, 2004, 25(4):269-276. |
| [14] | FANG Y, KANG H, WANG W, et al. Study on polyethylene glycol/epoxy resin composite as a form-stable phase change material[J]. Energy Conversion and Management, 2010, 51(12):2757-2761. |
| [15] | FENG Q, YANG J, LIU Y, et al. Simultaneously enhanced cryogenic tensile strength, ductility and impact resistance of epoxy resins by polyethylene glycol[J]. Journal of Materials Science & Technology, 2014, 30(1):90-96. |
| [16] | ZAVAREH S, SAMANDARI G. Polyethylene glycol as an epoxy modifier with extremely high toughening effect:Formation of nanoblend morphology[J]. Polymer Engineering & Science, 2014, 54(8):1833-1838. |
| [17] | WANG S, LI Q, ZHANG W, et al. Crack resistance test of epoxy resins under thermal shock[J]. Polymer Testing, 2002, 21(2):195-199. |
| [18] | 全国塑料标准化技术委员会. 塑料悬臂梁冲击强度的测定:GB/T 1843-2008[S]. 北京:中国标准出版社, 2008. National Technical Committee on Plastic of Standardization Administration of China. Plastic-Determination of izod impact strength:GB/T 1843-2008[S]. Beijing:Standard Press of China, 2008(in Chinese). |
| [19] | IMANAKA M, MOTOHASHI S, NISHI K, et al. Crack-growth behavior of epoxy adhesives modified with liquid rubber and cross-linked rubber particles under mode I loading[J]. International Journal of Adhesion and Adhesives, 2009, 29(1):45-55. |
| [20] | QIN C, SHEN J, HU Y, et al. Miscibility, crystallization behavior and specific intermolecular interactions in thermosetting polymer blends of novolac epoxy resin and polyethylene glycol[J]. Polymer Engineering & Science, 2008, 48(3):556-563. |
| [21] | PEARSON R A, YEE A F. Influence of particle size and particle size distribution on toughening mechanisms in rubber-modified epoxies[J]. Journal of Materials Science, 1991, 26(14):3828-3844. |
