|
|
- 2018
静电纺纤维素纳米晶体/壳聚糖-聚乙烯醇复合纳米纤维的制备与表征
|
Abstract:
通过探索纤维素纳米晶体（CNC）添加量对壳聚糖-聚乙烯醇（CS-PVA）基体性能的影响，为静电纺CNC/CS-PVA复合纳米纤维的制备提供理论支撑。以CNC、CS和PVA为原料，采用静电纺丝法成功制备不同CNC含量（质量分数）的静电纺CNC/CS-PVA复合纳米纤维，并通过SEM、TGA和FTIR等分析手段对CNC/CS-PVA复合纳米纤维的微观结构和性能进行了表征。结果表明：添加CNC后静电纺CNC/CS-PVA复合纳米纤维直径变大，表面变粗糙，力学性能和热学性能提高；随着CNC含量的增加，静电纺CNC/CS-PVA纤维的杨氏模量（E）和抗拉强度（σ）先增强后减弱，而外延起始温度继续上升。当CNC含量为3wt%时，静电纺CNC/CS-PVA复合纳米纤维力学性能最好，相比于CS-PVA复合纳米纤维，E和σ分别提高了43.9%和24.8%；当CNC含量为20wt%时，静电纺CNC/CS-PVA复合纳米纤维直径分布不均匀，可以观察到单根纤维表面存在少量的球状结构物质，同时外延起始温度达到328.83℃；FTIR分析得出，CNC与CS和PVA之间只存在分子间的相互作用而没有发生化学反应；随着溶液的酸性减弱，碱性增强，不同CNC含量的静电纺CNC/CS-PVA复合纳米纤维稳定性逐渐提高，而CNC含量对其稳定性影响不大。 The effect of cellulose nanocrystals (CNC) addition on the properties of chitosan/polyvinyl alcohol (CS-PVA) matrix was explored, and the theoretical support for the fabrication of electrospun CNC/CS-PVA composite nanofibers was further provided. Using CNC, CS and PVA as raw materials, the CNC/CS-PVA composite nanofibers with different CNC content (mass fraction) were successfully prepared by the method of electrospinning. The microstructure and properties of the composite nanofibers were analyzed by SEM, TGA and FTIR. The results show that the addition of CNC leads to increased average diameter of the CNC/CS-PVA composite nanofibers, while the composite nanofibers surface becomes rougher. The mechanical properties and thermal behavior are significantly improved. With the increase of CNC content, the Young's modulus (E) and tensile strength (σ) of CNC/CS-PVA composite nanofibers first enhance and then weaken, while the epitaxial starting temperature continues to rise. When the content of CNC is 3wt%, the mechanical properties of electrospun CNC/CS-PVA composite nanofibers have the maximum values. Compared with CS-PVA composite nanofibers, E and σ of the nanofibers with CNC incorporation increase by 43.9% and 24.8%, respectively. As CNC content is 20wt%, the electrospun CNC/CS-PVA composite nanofibers diameter distribution is not uniform, some spherical structure is observed on the surface of the single fiber, and the epitaxial initiation temperature reaches to 328.83℃. FTIR analysis showes that only physical interaction is present among CNC, CS and PVA, but no chemical reaction occurres. The stability of the electrospun CNC/CS-PVA composite nanofibers with different CNC contents gradually increases with increased acidity of the solution, while the CNC loading has little effect on it. 国家自然科学基金（31470580）
| [1] | OHKAWA K, CHA D, KIM H, et al. Electrospinning of chitosan[J]. Macromolecular Rapid Communications, 2004, 25(18):1600-1605. |
| [2] | 丁彬, 俞健勇. 静电纺丝与纳米纤维[M]. 北京:中国纺织出版社, 2013, 123-140. DING Bin, YU Jianyong. Electrospinning and nanofibers[M]. Beijing:China Textile, 2013, 123-140(in Chinese). |
| [3] | HUAN Siqi, BAI Long, CHENG Wanli, et al. Manufacture of electrospun all-aqueous poly(vinyl alcohol)/cellulose nanocrystal composite nanofibrous mats with enhanced properties through controlling fibers arrangement and microstructure[J]. Polymer, 2016, 92:25-35. |
| [4] | 徐苏华, 古菊, 罗远芳, 等. 纳米微晶纤维素对白炭黑/天然橡胶复合材料性能的影响[J]. 复合材料学报, 2011, 28(6):39-44. XU Fanghua, GU Ju, LUO Yuanfang, et al. Influence of nanocrystalline cellulose on SiO2/natural rubber composites[J]. Acta Materiae Compositae Sinica, 2011, 28(6):39-44(in Chinese). |
| [5] | 刘国相, 宦思琪, 韩广萍, 等. 静电纺丝法制备PLA/CNCs纳米复合薄膜及其性能研究[J]. 功能材料, 2016(11):11151-11155, 11161. LIU Guoxiang, HUAN Siqi, HAN Guangping, et al. Fabrication and characterization ofelectrospun PLA/CNCs nanofibrousfilms[J]. Functional Materials, 2016(11):11151-11155, 11161(in Chinese). |
| [6] | 刘桦, 罗丙红, 陈睿鹏, 等. 纳米纤维素晶须增强增韧聚(L-乳酸)复合材料的制备与表征[J]. 复合材料学报, 2015, 32(6):1703-1713. LIU Hua, LUO Binghong, CHEN Ruipeng, et al. Preparation and characterization of nanocellulose whiskers reinforced and toughend poly(L-lactide) based composites[J]. Acta Materiae Compositae Sinica, 2015, 32(6):1703-1713(in Chinese). |
| [7] | LEE J, DENG Y. Increased mechanical properties of aligned and isotropic electrospun PVA nanofiber webs by cellulose nanowhisker reinforcement[J]. Macromolecular Research, 2012, 20(1):76-83. |
| [8] | 宦思琪, 程万里, 白龙, 等. 静电纺丝制备聚苯乙烯/纳米纤维素晶体纳米复合薄膜及其性能表征[J]. 高分子材料科学与工程, 2016(03):141-146. HUAN Siqi, CHENG Wanli, BAI Long, et al. Fabrication and characterization of electrospun polystyrene/cellulose nanocrystals nanofibrous films[J]. Polymer Materials Science and Engineering, 2016(03):141-146(in Chinese). |
| [9] | 杨文静, 付静, 何磊, 等. 静电纺丝制备壳聚糖/聚己内酯血管支架及表征[J]. 复合材料学报, 2011, 28(1):104-108. YANG Wenjing, FU Jing, HE Lei, et al. Preparation and characterization of chitosan/polycaprolactone vascular scaffolds by electrospinning[J]. Acta Materiae Compositae Sinica, 2011, 28(1):104-108(in Chinese). |
| [10] | WANG M, ROY A K, WEBSTER T J W. Development of chitosan/poly (vinyl alcohol) electrospun nanofibers for improved wound healing[J]. Frontiers in Physiology, 2017, 7:683. |
| [11] | 何创龙, 黄争鸣, 韩晓建, 等. 同轴射流技术制备纳米复合材料研究进展[J]. 复合材料学报, 2005, 22(6):1-8. HE Chuanglong, HUANG Zhengming, HAN Xiaojian, et al. Recent development of the nanocomposites prepared by coaxial jet technology[J]. Acta Materiae Compositae Sinica, 2005, 22(6):1-8(in Chinese). |
| [12] | 顾蓉, 张佳, 郭康权, 等. 葡甘聚糖-壳聚糖-聚乙烯醇复合胶黏剂的流变特性[J]. 复合材料学报, 2011, 28(1):37-42. GU Rong, ZHANG Jia, GUO Kangquan, et al. Rheological properties of konjac glucomannan-chitosan-PVA laminating adhesive[J]. Acta Materiae Compositae Sinica, 2011, 28(1):37-42(in Chinese). |
| [13] | WANG F, GE M. Fibrous mat of chitosan/polyvinyl alcohol/containing cerium (Ⅲ) for the removal of chromium (VI) from aqueous solution[J]. Textile Research Journal, 2012, 83(6):628-637. |
| [14] | 张慧敏, 阮弦, 胡勇有, 等. 静电纺壳聚糖/聚乙烯醇纳米纤维膜对Cu2+、Ni2+及Cd2+的吸附特性[J]. 环境科学学报, 2015, 35(1):184-193. ZHANG Huimin, RUAN Xian, HU Yongyou, et al. Adsorptive of Cu2+, Ni2+ and Cd2+ on chitosan/poly(vinyl alcohol) nanofiber[J]. Journal of Environmental Science, 2015, 35(1):184-193(in Chinese). |
| [15] | XU R, TANG R, LIU S, et al. An environmentally-friendly enzyme-based nanofibrous membrane for 3, 3', 5, 5'-tetrabromobisphenol removal[J]. RSC Advances, 2015, 5(79):64091-64097. |
| [16] | 王群旺, 熊杰, 张红萍, 等. 聚丁二酸丁二醇酯调控丝素蛋白超细纤维膜形貌及其力学性能[J]. 复合材料学报, 2010, 27(5):24-28. WANG Qunwang, XIONG Jie, ZHANG Hongping, et al. Morphology and mechanical properties of electrospun silk fibroin ultrafine fibrous membranes adjusted and controlled by PBS[J]. Acta Materiae Compositae Sinica, 2010, 27(5):24-28(in Chinese). |
| [17] | GENG X, KWON O H, JANG J. Electrospinning of chitosan dissolved in concentrated acetic acid solution[J]. Biomaterials, 2005, 26(27):5427-5432. |
| [18] | HOMAYONI H, RAVANDI S A H, VALIZADEH M. Electrospinning of chitosan nanofibers:Processing optimization[J]. Carbohydrate Polymers, 2009, 77(3):656-661. |
| [19] | PERESIN M S, HABIBI Y, ZOPPE J O, et al. Nanofiber composites of polyvinyl alcohol and cellulose nanocrystals:Manufacture and characterization[J]. Biomacromolecules, 2010, 11(3):674-681. |
| [20] | BONDESON D, MATHEW A, OKSMAN K. Optimization of the isolation of nanocrystals from microcrystalline cellulose by acid hydrolysis[J]. Cellulose, 2006, 13(2):171-180. |
| [21] | HUAN S, BAI L, LIU G, et al. Electrospun nanofibrous composites of polystyrene and cellulose nanocrystals:manufacture and characterization[J]. RSC Advances, 2015, 5(63):50756-50766. |
| [22] | 王策, 卢晓峰. 有机纳米功能材料:高压静电纺丝技术与纳米纤维[M]. 北京:科学出版社, 2011:39-42. WANG Ce, LU Xiaofeng. Organic nanomaterials:High-voltage electrospinning technology and nanofibers[M]. Beijing:Science Publishing, 2011:39-42(in Chinese). |
| [23] | PERESIN M S, HABIBI Y, ZOPPE J O, et al. Nanofiber composites of polyvinyl alcohol and cellulose nanocrystals:Manufacture and characterization[J]. Biomacromolecules, 2010, 11(3):674-681. |
| [24] | 顾书英, 任杰. 聚合物基复合材料[M]. 北京:化学工业出版社, 2007:38-44. GU Shuying, REN Jie. Research methods of polymers[M]. Beijing:Chemical Industry, 2000:12-17(in Chinese). |
| [25] | MIN B M, LEE S W, LIM J N, et al. Chitin and chitosan nanofibers:Electrospinning of chitin and deacetylation of chitin nanofibers[J]. Polymer, 2004, 45(21):7137-7142. |
| [26] | DAI L, LONG Z, REN X, et al. Electrospun polyvinyl alcohol/waterborne polyurethane composite nanofibers involving cellulose nanofibers[J]. Journal of Applied Polymer Science, 2015, 131(22):547-557. |
| [27] | MIYA M, IWAMOTO R, MIMA S. FTIR study of intermolecular interactions in polymer blends[J]. Journal of Polymer Science:Polymer Physics Edition, 1984, 22(6):1149-1151. |
| [28] | 张美珍, 柳百坚, 谷晓昱. 聚合物研究方法[M]. 北京:2000:12-17. ZHANG Meizhen, YANG Baijian, GU Xiaoyu. Research methods of polymers[M]. Beijing:China Light Industry, 2000:12-17(in Chinese). |
| [29] | HAIDER S, PARK S Y. Preparation of the electrospun chitosan nanofibers and their applications to the adsorption of Cu (Ⅱ) and Pb (Ⅱ) ions from an aqueous solution[J]. Journal of Membrane Science, 2009, 328(1):90-96. |
