|
|
- 2018
基于双锥砂轮的环面蜗轮滚刀前刀面成形方法
|
Abstract:
摘要 多头环面蜗轮滚刀通常采用螺旋槽，以降低刀齿负前角的绝对值、并均衡每个刀齿左右两侧的前角，从而提高滚刀的切削性能。由于环面蜗轮滚刀螺旋线上各处的螺旋升角不同，所以各个刀齿左右两侧的前角均衡问题更为复杂，鲜有螺旋槽前刀面的精确成形方法的研究。基于环面蜗杆专用数控机床，提出采用双锥砂轮磨削螺旋槽环面蜗轮滚刀前刀面的方法，根据齿轮啮合理论，建立由双锥产形面展成平面二次包络环面蜗轮滚刀螺旋槽前刀面的数学模型，给出每个刀齿两侧在分度环面螺旋线上的前角计算公式。算例计算结果表明：如果采用直槽滚刀，对应的前角在-19.530 3°~19.530 4°；通过合理的参数选择，可使得螺旋槽滚刀对应的前角在-8.1°~7.3°，有效减小了刀齿负前角的绝对值。对环面蜗轮滚刀螺旋槽进行仿真加工，并且在仿真软件中对前角进行测量，测量结果与计算结果相吻合，证明本文方法的正确性。
Abstract：For multi-thread hourglass worm gear hobs, spiral flutes are typically used to reduce the absolute value of the negative rake angle and to equalize the rake angles on the left and right sides of each tooth, which will improve the cutting performance of the hob. Because of the different spiral angle on the basic worm helical surface, the rake angle on both sides of each tooth is more difficult to balance. However, there are few researches on the precise forming method of the spiral flute rake face. Based on the NC machine tool for hourglass worm, a method for grinding the rake face of spiral flute with double-cone grinding wheel is proposed. According to the gear meshing theory, a mathematical model was established for the rake face of the planar double enveloping hourglass worm gear hob spiral flute formed by the double-cone grinding surface. The formula for calculating the rake angle on both sides of the tooth is given. The calculation results show that if the hob with straight flute is used, the rake angles are between -19.530 3° and 19.530 4°. Through proper parameter selection, the rake angles can be between -8.1° and 7.3° when the hob with spiral flute is used, which effectively reduces the absolute value of the negative rake angle of the tooth. The spiral flute of hourglass worm gear hob was simulated and the rake angle was measured in the simulation software. The measured results coincide with the calculated results and this proves the correctness of the method.
| [1] | 柳冠伊.包络环面蜗轮滚刀数控成形理论及技术研究[D].北京:中国农业大学,2016:13-14.LIU G Y.Research on CNC relief grinding technology of enveloping worm gear hob[D].Beijing:China Agricultural University,2016:13-14(in Chinese). |
| [2] | 杨杰,李海涛,芮成杰,等.环面蜗轮滚刀螺旋槽前刀面设计及修正方法[J].北京航空航天大学学报,2008,44(9):1878-1887.YANG J,LI H T,RUI C J,et al.Design and correct method of spiral flutes rake face of an hourglass worm gear hob[J].Journal of Beijing University of Aeronautics and Astronautics,2008,44(9):1878-1887(in Chinese). |
| [3] | 董学朱.齿轮啮合理论基础[M].北京:机械工业出版社,1989:90-92.DONG X Z.Gear meshing theory[M].Beijing:China Machine Press,1989:90-92(in Chinese). |
| [4] | LIU G Y,WEI W J,DONG X Z,et al.Relief grinding of planar double-enveloping worm gear hob using a four-axis CNC grinding machine[J].The International Journal of Advanced Manufacturing Technology,2016,89(9-12):3631-3640. |
| [5] | 杨胜群,唐秀梅.VERICUT数控加工仿真技术[M].北京:清华大学出版社,2010:77-81.YANG S Q,TANG X M.VERICUT NC machining simulation technology[M].Beijing:Tsinghua University Press,2010:77-81(in Chinese). |
| [6] | 唐建生.金属切削与刀具[M].武汉:武汉理工大学出版社,2009:188-189.TANG J S.Cutting and cutting tools[M].Wuhan:Wuhan University of Technology Press,2009:188-189(in Chinese). |
| [7] | 周良墉.环面蜗杆修型原理及制造技术[M].长沙:国防科技大学出版社,2005:558-559.ZHOU L Y.The modification principle and manufacturing technology of hourglass worm[M].Changsha:National University of Defense Technology Press,2005:558-559(in Chinese). |
| [8] | 董李扬.包络环面蜗杆副蜗轮滚刀数控加工技术的研究[D].北京:中国农业大学,2013:15-20.DONG L Y.Research on NC machining technology of enveloping worm gear hob[D].Beijing:China Agricultural University,2013:15-20(in Chinese). |
| [9] | YANG J,LI H T,RUI C J,et al.A method to generate the spiral flutes of an hourglass worm gear hob[J].International Journal of Mechanical Design,2018,140(6):063301. |
| [10] | CHANG S L.Helix gash of hob cutter manufactured by milling[J].Journal of Materials Processing Technology,2003,142(2):569-575. |
| [11] | 舒勤业.双锥面二次包络环面蜗杆副及其关键制造装备的设计与研究[D].杭州:浙江大学,2015:21-30.SHU Q Y.Design and research of dual-cone double enveloping hourglass worm gear pair and its key manufacturing equipment[D].Hangzhou:Zhejiang University,2015:21-30(in Chinese). |
| [12] | 刘杰华.大螺旋槽零前角滚刀前刀面重磨时砂轮廓形的修整计算[J].磨床与磨削,1996(4):25-26.LIU J H.Dressing calculation of the profile of the grinding wheel on the rake face of the hob with zero rake angle[J].Grinding Machine and Grinding,1996(4):25-26(in Chinese). |
| [13] | 陈就,刘丰林,康权.一种滚刀径向铲磨优化方法[J].中国机械工程,2014,25(14):1883-1887.CHEN J,LIU F L,KANG Q.An optimization method for hob relief grinding[J].China Mechanical Engineering,2014,25(14):1883-1887(in Chinese). |
| [14] | GUNAY M.Investigation of the effect of rake angle on main cutting force[J].International Journal of Machine Tools & Manufacture,2004,44(9):953-959. |
| [15] | GUNAY M.Experimental investigation of the effect of cutting tool rake angle on main cutting force[J].Journal of Materials Processing Technology,2005,166(1):44-49. |
| [16] | SAGLAM H,UNSACAR F,YALDIZ S.Investigation of the effect of rake angle and approaching angle on main cutting force and tool tip temperature[J].International Journal of Machine Tools and Manufacture,2006,46(2):132-141. |
| [17] | LITVIN F L.Theory of gearing[M].Washington,D.C.:NASA Reference Publication,1989:57-62. |
| [18] | 吴序堂.齿轮啮合理论[M].2版.西安:西安交通大学出版社,2009:104-110.WU X T.Gear meshing theory[M].2nd ed.Xi'an:Xi'an Jiao Tong University Press,2009:104-110(in Chinese). |
| [19] | 姜正健,张伟,李铸宇.微钻的前角计算及其钻削试验[J].大连工业大学学报,2011,30(2):145-147.JIANG Z J,ZHANG W,LI Z Y.Calculation of the rake angle of micro drill and drilling test[J].Journal of Dalian Institute of Light Industry,2011,30(2):145-147(in Chinese). |
| [20] | 董学朱.环面蜗杆传动设计和修形[M].北京:机械工业出版社,2004:14-15.DONG X Z.Design and modification of enveloping worm gearing[M].Beijing:Mechanical Industry Press,2004:14-15(in Chinese). |
| [21] | 罗文军,陈永洪,张光辉.平面包络环面蜗杆齿面的螺旋线误差检测及溯源[J].西南交通大学学报,2015,50(2):279-285.LUO W J,CHEN Y H,ZHANG G H.Helix error testing and tracing on planar enveloping hourglass worm tooth surface[J].Journal of Southwest Jiaotong University,2015,50(2):279-285(in Chinese). |
| [22] | 郝建军,张光辉,施全.环面蜗轮滚刀可重磨性研究与应用——环面蜗轮滚刀理论分析[J].重庆理工大学学报(自然科学版),2010,24(6):23-28.HAO J J,ZHANG G H,SHI Q.Research and application on annular worm gear hob rlieving grinding-Annular worm gear hob theory[J].Journal of Chongqing University of Technology (Natural Science Edition),2010,24(6):23-28(in Chinese). |
| [23] | ZHAO Y P,SU D Z,ZHANG Z.Meshing analysis and technological parameters selection of dual tori double-enveloping toroidal worm drive[J].Mechanism and Machine Theory,2010,45(9):1269-1285. |
| [24] | YANG J,LI H T,RUI C J.Research on a generating method of spiral flutes of hourglass worm gear hob[C]//Proceedings of the ASME Design Engineering Technical Conference.NewYork:ASME,2017:10. |
