|
|
- 2017
摆动活齿传动的热弹耦合变形
|
Abstract:
为了提高摆动活齿的传动性能，根据摆动活齿传动的啮合原理，分析了在摆动活齿传动中，活齿与内齿轮的接触传热过程；探讨了活齿与内齿轮啮合副产生的摩擦热流的计算方法；利用有限元分析方法建立了内齿轮的有限元分析模型；提出了摆动活齿传动轮齿本体温度分布、接触弹性变形和热弹耦合变形的分析计算方法.研究结果表明：内齿轮的最高温度出现在工作齿廓曲线的拐点附近，内齿轮的热变形增大了齿厚，对轮齿的弹性变形有一定的补偿作用，应用本文方法计算得到的内齿轮热弹变形符合实际工况，轮齿最大的热弹耦合变形量为0.045 mm.
： To improve the transmission performance of swing movable teeth transmission, the contact heat transfer process between the movable teeth and internal gear was analyzed and the calculation method of the friction heat flux generated by the meshing pair was proposed according to the meshing principle of swing movable teeth transmission. Then, a finite element analysis model of the internal gear was established, based on which calculation methods of the body temperature field distribution, contact elastic deformation, and coupled thermo-elastic deformation of the internal gear during swing movable teeth transmission were put forward. The results of a case study show that the highest temperature in the internal gear appears near the inflection point of the internal gear profile curve; and the thermal deformation of the internal gear increases its tooth thickness, providing a certain compensation for the elastic deformation of the internal gear. In addition, the coupled thermo-elastic deformation of the internal gear obtained by the proposed method conforms with the actual working condition, and the maximum value is 0.045 mm
| [1] | 曲继方. 活齿传动理论[M]. 北京:机械工业出版社,1993: 75-85,200. |
| [2] | 王淑营,徐礼钜,梁尚明. 摆动活齿传动的动力学模型[J]. 西南交通大学学报,2004,39(4): 472-475. WANG Shuying, XU Liju, LIANG Shangming. Dynamic analysis of swing movable teeth drive[J]. Journal of Southwest Jiaotong University, 2004, 39(4): 472-475. |
| [3] | 桂长林,李震. 齿轮的胶合计算和实验研究[J]. 机械工程学报,1995,31(5): 1-8. GUI Changlin, LI Zhen. Gear agglutination calculation and experimental study[J]. Chinese Journal of Mechanical Engineering, 1995, 31(5): 1-8. |
| [4] | 曲继方. 活齿传动齿廓修形原理及方法研究[J]. 机械工程学报,1991,27(2): 85-91. QU Jifang. Research on the principle and methods of the tooth profile modification of the oscillating tooth drive[J]. Chinese Journal of Mechanical Engineering, 1991, 27(2): 85-91. |
| [5] | 梁尚明,张杰,姚进. 摆动活齿传动弹流润滑下的摩擦功耗研究[J]. 西南交通大学学报,2013,48(6): 1105-1109. LIANG Shangming, ZHANG Jie, YAO Jin. Friction power loss of swing movable teeth transmission under the elastohydrodynamic lubrication[J]. Journal of Southwest Jiaotong University, 2013, 48(6): 1105-1109. |
| [6] | 乔慧,李剑锋,陈兴,等. 二齿差摆动活齿传动齿廓方程及几何性质分析[J]. 机械设计与制造,2012(11): 40-42. QIAO Hui, LI Jianfeng, CHEN Xing, et al. The equations of tooth profile and geometry analysis of two-tooth difference swing movable tooth transmission[J]. Machinery Design & Manufacture, 2012(11): 40-42. |
| [7] | 梁尚明. 摆动活齿传动的研究[D]. 成都:四川大学,2000. |
| [8] | 樊庆文,王小龙,李廷玉,等. 摆动活齿传动中影响胶合磨损的主要因素[J]. 四川大学学报:工程科学版,2003,35(5): 24-26. FAN Qingwen, WANG Xiaolong, LI Tingyu,et al. Study on main causes of affecting the gluey wear of swing movable teeth drive[J]. Journal of Sichuan University: Engineering Science Edition, 2003, 35(5): 24-26. |
| [9] | 梁尚明,张杰,贺飞飞. 摆动活齿传动齿面闪温研究[J]. 四川大学学报:工程科学版,2013,45(3): 176-181. LIANG Shangming, ZHANG Jie, HE Feifei. Study on flash temperature of swing movable teeth transmission[J]. Journal of Sichuan University:Engineering Science Edition, 2013, 45(3): 176-181. |
| [10] | 陈清江. 摆动活齿传动机构参数化设计[D].秦皇岛:燕山大学,2011. |
| [11] | 曾强,李鹏,陈兵奎. 空间凸轮活齿传动的接触有限元分析[J]. 机械,2004,31(增刊1): 12-14. ZENG Qiang, LI Peng, CHEN Binkui. The contact finite element analysis of a new spatial cam sliding transmission[J]. Machinery, 2004, 31(Sup.1): 12-14. |
| [12] | 李绍彬. 高速重载齿轮传动热弹变形及非线性耦合动力学研究[D]. 重庆:重庆大学,2004. |
| [13] | BLOK H.The flash temperature concept[J]. Wear, 1963, 6(6): 483-494. |
| [14] | 费业泰. 机械热变形理论及应用[M]. 北京:国防工业出版社,2009: 5-100. |
| [15] | 宜亚丽,安子军. 摆动活齿传动齿廓曲线特性分析与研究[J]. 机械设计,2008,25(8): 57-59. YI Yali, AN Zijun. Analysis and study on characteristics of tooth profile curve in swinging movable teethed transmission[J]. Journal of Machine Design, 2008, 25(8): 57-59. |
