|
|
- 2017
圆形烟风道支座与加固肋匹配特性
|
Abstract:
摘要： 采用有限元数值计算的方法,对圆形烟风道的鞍式支座与环形加固肋的匹配问题进行分析,确定了鞍式支座与加固肋的最优匹配方式。试验结果表明:单纯使用鞍形支座,容易导致道体和支座接触区域的应力集中,最大应力值远超许用应力;在支座附近设置重肋,可以有效降低形变并提高屈曲系数,但是难以降低最大应力。将支座设置在重肋下方,不仅可以大幅度降低形变,屈曲安全系数也最高,同时能够大幅度减小支座与加固肋接触区的应力,可以满足长期使用的安全性要求。支座包角对应力集中和屈曲特性的影响较小。
Abstract: The matching property of saddle support and stiffener on circular exhaust duct was studied, and the optimal position of heavy stiffener and saddle supports were determined by the finite element method(FEM). The results showed that the use of pure saddle supports might lead to stress concentration on the contact area of saddle and duct, meanwhile the maximum stress could exceed the allowable stress. The heavy stiffener near the supports could decrease the deformation and increase the buckling factor, while could hardly decrease the maximum stress. Saddle supports under the heavy stiffener could obviously decrease the deformation and increase the buckling factor, and could decrease the stress on the contact area of support and duct so that would meet the need of long-term security. The influence of wrap-angle to the stress concentration and buckling property was not obvious
| [1] | 王乃华. 快速悬浮床烟气脱硫[J]. 山东大学学报(工学版), 2003, 33(5): 502-506. WANG Naihua. Flue gas desulfurization of fast suspension bed[J]. Journal of Shandong University(Engineering Science), 2003, 33(5):502-506. |
| [2] | 郭娟丽. ANSYS在电厂烟风道设计中的应用[J]. 电力勘测设计, 2015, 4(8):38-41. GUO Juanli. Application of ANSYS to flue gas and air duct design in power plant[J]. Electric Power Survey & Design, 2015, 4(8):38-41. |
| [3] | 周俊. 圆形烟风道与节能降耗[J]. 江苏锅炉, 2010(4): 40-42. ZHOU Jun. Circular exhaust duct and energy saving[J]. Jiangsu Boiler, 2010(4): 40-42. |
| [4] | 钮树强. 鞍座设置对大型卧式容器筒体受力的影响分析[D].杭州:浙江工业大学,2013. NIU Shuqiang. Analysis of influence of saddle setting on the cylinder stress of large horizontal vessels[D]. Hangzhou: Zhejiang University of Technology, 2013. |
| [5] | 全国压力容器标准化技术委员会. 容器支座 第一部分: 鞍式支座:JB/T 4712.1—2007[S]. 北京: 中国标准出版社, 2007. |
| [6] | 中国电力企业联合会. 电厂动力管道设计规范:GB 50764—2012[S]. 北京: 中国计划出版社, 2012. |
| [7] | 周锐. 大容量机组圆形烟道设计特点[J]. 发电设备, 2010, 24(3):190-192. ZHOU Rui. Design features of circular flues for large capacity power units[J]. Power Equipment, 2010, 24(3):190-192. |
| [8] | 侯庆伟, 石桂荣, 李勇臣, 等. 湿法烟气脱硫系统的pH值及控制步骤分析[J]. 山东大学学报(工学版), 2005, 35(5): 37-40. HOU Qingwei, SHI Guirong, LI Yongchen, et al. Analysis on pH value and control step in wet flue gas desulfurization[J]. Journal of Shandong University(Engineering Science), 2005, 35(5):37-40. |
| [9] | 石亚超, 朱桂明, 郝若锦, 等. 圆形烟道在烟气脱硫脱硝装置中的应用探讨[J]. 化工机械, 2013, 40(3): 369-372. SHI Yachao, ZHU Guiming, HAO Ruojin, et al. Research on circular flue application in flue gas desulfurization system[J]. Chemical Machinery, 2013, 40(3): 369-372. |
| [10] | 胡位勇. 基于ABAQUS的圆形烟风管道有限元建模及计算软件二次开发[D]. 重庆: 重庆大学, 2013. HU Weiyong. Finite element modeling and secondary development on circular exhaust duct based on ABAQUS[D]. Chongqing: Chongqing University, 2013. |
| [11] | 全国钢标准化技术委员会. 热轧型钢:GB/T 706—2008[S]. 北京: 中国标准出版社, 2008. |
| [12] | BODNER S R. General instability of a ring-stiffened, circular cylindrical shell under hydrostatic pressure[J]. Journal of Applied Mechanics, 1957(24): 269-277. |
| [13] | 冯若愚, 陈瑛, 柏洁. 水平圆柱薄壳非轴对称荷载作用内力分析[J]. 力学与实践, 2016, 38(5): 531-537. FENG Ruoyu, CHEN Ying, BAI Jie. Force analysis of thin-walled horizontal circular cylindrical shell under non-axisymmetric loading[J]. Mechanics in Engineering, 2016, 38(5): 531-537. |
| [14] | 张翼, 张晋军. 鞍座包角和宽度对双支座卧式容器筒体应力分布影响的研究[J]. 化工设备与管道, 2008, 45(6):7-11. ZHANG Yi, ZHANG Jinjun. Study of influence of contact angle and width of saddle to stress distribution in horizontal vessel with double saddles[J]. Process Equipment and Piping, 2008, 45(6):7-11. |
| [15] | 钱成续. 火力发电厂烟风煤粉管道技术规程配套设计计算方法[M]. 北京: 中国电力出版社, 2004. |
| [16] | 王欣, 郭小明, 张辉, 等. 火力发电厂烟风煤粉管道加固肋设计计算分析[J]. 电力科学与工程, 2006(3): 17-20. WANG Xin, GUO Xiaoming, ZHANG Hui, et al. Design analysis of stiffening ribs for air, flue gas and pulverized coal piping in thermal power plants[J]. Power Science and Engineering, 2006(3): 17-20. |
| [17] | 袁江涛. 火电厂圆形烟风道设计中的有限元分析方法[D]. 重庆: 重庆大学, 2011. YUAN Jiangtao. Finite element method in design of circular exhaust duct of thermal power unit[D]. Chongqing: Chongqing University, 2011. |
| [18] | 董祖成. 300 MW机组W型火焰锅炉二次风道改造[J]. 热力发电, 2008, 37(8): 40-44. DONG Zucheng. Retrofit of secondary air duct for W-shaped flame boiler of 300MW unit[J]. Thermal Power Generation, 2008, 37(8):40-44. |
| [19] | 赵经濂, 傅文玲, 杨虹. 脱硫烟道壁厚及其加固肋设计优化探讨[J]. 电力设备, 2005, 6(11):70-72. ZHAO Jinglian, FU Wenling, YANG Hong. Research on the optimum design of FGD flue thickness and its reinforcement[J]. Electrical Equipment, 2005, 6(11):70-72. |
| [20] | 邓海文. 烟风道加固肋组合截面特性计算[J]. 湖北电力, 2011, 35(1): 52-53, 67. DENG Haiwen. Reaserch on calculation of air & flue gas ducts stiffener combination section characteristic[J]. Hubei Electric Power, 2011, 35(1): 52-53, 67. |
