A hybrid solar collector was designed to investigate the effects of combining two different solar collector techniques on the overall collector’s effectiveness. While most solar collectors focus only on one solar collection method, the small hybrid system uses a flat plate collector in conjunction with five evacuated tubes to absorb the most energy possible from both direct and diffuse solar radiation. Data was collected over four months while the system operated at different flow rates and with various levels of available insolation from the sun to evaluate the performance of the solar collector. To understand the relative contribution of the flat plate collector and the evacuated tubes, temperature differences across each part of the system were measured. The results indicate the average first law efficiency of the hybrid system is 43.3%, significantly higher than the performance of the flat plate alone. An exergy analysis was performed for this system to assess the performance of the flat plate system by itself. Results of the second law analysis were comparable to the exergetic efficiencies of other experimental collectors, around 4%. Though the efficiencies were in the expected range, they reveal that further improvements to the system are possible.
References
[1]
Arora, S., Chitkara, S., Udayakumar, R. and Ali, M. (2011) Thermal Analysis of Evacuated Solar Tube Collectors. Journal of Petroleum and Gas Engineering, 4, 74-82.
http://www.academicjournals.org/journal/JPGE/article-abstract/CF81F1C3607
[2]
Commercial Solar Water Heaters|Evacuated Tube Solar Thermal Collectors.
http://www.solarpanelsplus.com/evacuated-tube-collectors/
[3]
Ayompe, L.M., Duffy, A., Mc Keever, M., Conlon, M. and McCormack, S.J. (2011) Comparative Field Performance Study of at Plate and Heat Pipe Evacuated Tube Collectors (ETCs) for Domestic Water Heating Systems in a Temperate Climate. Energy, 36, 3370-3378. https://doi.org/10.1016/j.energy.2011.03.034
[4]
Chaichana, C., Kiatsiriroat, T. and Nuntaphan, A. (2010) Comparison of Conventional Flat-Plate Solar Collector and Solar Boosted Heat Pump Using Unglazed Collector for Hot Water Production in Small Slaughterhouse. Heat Transfer Engineering, 31, 419-429. https://doi.org/10.1080/01457630903375475
[5]
Gang, P., Jing, L. and Jie, J. (2011) Design and Analysis of a Novel Low-Temperature Solar Thermal Electric System with Two-Stage Collectors and Heat Storage Units. Renewable Energy, 36, 2324-2333. https://doi.org/10.1016/j.renene.2011.02.008
[6]
Yang, J.C., Jiang, Q.Y., Hou, J.X. and Luo, C.L. (2015) A Study on Thermal Performance of a Novel All-Glass Evacuated Tube Solar Collector Manifold Header with an Inserted Tube. International Journal of Photoenergy, 1-7.
[7]
Manek, A. and Karunanidhi, S.G. (2016) Performance Evaluation of ETC Using Booster Mirrors. International Conference on Emerging Engineering Trends and Science (ICEETS-2016), 20-27.
[8]
Said, Z., Alim, M.A. and Janajreh, I. (2015) Exergy Efficiency Analysis of a at Plate Solar Collector Using Graphene Based Nanouid. IOP Conference Series: Materials Science and Engineering, 92, 012015.
https://doi.org/10.1088/1757-899X/92/1/012015
[9]
Kalogirou, S.A., Karellas, S., Badescu, V. and Braimakis, K. (2016) Exergy Analysis on Solar Thermal Systems: A Better Understanding of Their Sustainability. Renewable Energy, 85, 1328-1333. https://doi.org/10.1016/j.renene.2015.05.037
[10]
Jafarkazemi, F. and Ahmadifard, E. (2013) Energetic and Exergetic Evaluation of at Plate Solar Collectors. Renewable Energy, 56, 55-63.
https://doi.org/10.1016/j.renene.2012.10.031
[11]
Ge, Z., Wang, H.T., Wang, H., Zhang, S.Y. and Guan, X. (2014) Exergy Analysis of Flat Plate Solar Collectors. Entropy, 16, 2549-2567.
https://doi.org/10.3390/e16052549
[12]
Hamed, M., Snoussi, A. and Brahim, A.B. (2014) Energy and Exergy Analysis of at Plate Solar Collectors in Transient Behaviors. 2014 5th International Renewable Energy Congress (IREC), IEEE, 1-6. https://doi.org/10.1109/IREC.2014.6826943
[13]
Zielinski, A., Dillon, H., Baldwin, B., Forinash, C., Zada, K., Stillinger, C. and Dieter, K. (2016) Design and Performance of a Small Hybrid Solar Collector. ASME 2016 Power Conference, ASME, V001T10A001.
[14]
Dieter, K., Stillinger, C., Dillon, H. and Zeilinski, A. (2016) Design and Build of an Electrical Generator and Load Control System for a Novel Small-Scale Hybrid Solar Thermal Collector. 2016 IEEE International Conference on Power System Technology, POWERCON 2016. https://doi.org/10.1109/POWERCON.2016.7754070
[15]
Moran, M.J., Shapiro, H.N., Boettner, D.D. and Bailey, M.B. (2010) Fundamentals of Engineering Thermodynamics. John Wiley & Sons.
