The aim of this paper is to model the steady-state condition of a rotary shaft seal (RSS) system. For this, an iterative thermal-mechanical algorithm was developed based on incremental finite element analyzes. The behavior of the seal’s rubber material was taken into account by a large-strain viscoelastic, so called generalized Maxwell model, based on Dynamic Mechanical Thermal Analyses (DMTA) and tensile measurements. The pre-loaded garter spring was modelled with a bilinear material model and the shaft was assumed to be linear elastic. The density, coefficient of thermal expansion and the thermal conductance of the materials were taken into consideration during simulation. The friction between the rotary shaft seal and the shaft was simplified and modelled as a constant parameter. The iterative algorithm was evaluated at two different times, right after assembly and 1 h after assembly, so that rubber material’s stress relaxation effects are also incorporated. The results show good correlation with the literature data, which state that the permissible temperature for NBR70 (nitrile butadiene rubber) material contacting with ~80 mm shaft diameter, rotating at 2600/min is 100°C. The results show 107°C and 104°C for the two iterations. The effect of friction induced temperature, changes the width of the contact area between the seal and the shaft, and significantly reduces the contact pressure.
Simmer, W. (1938) Aus elastischem Werkstoff bestehende Dichtung für umlaufende Wellen oder hin und her gehende Stangen. Patentschrift DE729128C.
[4]
Frolich, D., Magyar, B. and Sauer, B. (2014) A Comprehensive Model of Wear, Friction and Contact Temperature in Radial Shaft Seals. Wear, 311, 71-80.
https://doi.org/10.1016/j.wear.2013.12.030
[5]
Stakenborg, M.J.L. (1988) On the Sealing Mechanism of Radial Lip Seals. Tribology International, 21, 335-340. https://doi.org/10.1016/0301-679X(88)90110-7
[6]
Stakenborg, M.J.L. and Ostayen, R.A.J. (1989) Radial Lip Seals, Thermal Aspects. Tribological Design of Machine Elements, 14, 79-88.
https://doi.org/10.1016/S0167-8922(08)70183-4
[7]
Kang, Y.S. and Sadeghi, F. (1997) Numerical Analysis of Temperature Distribution at the Lip Seal-Shaft Interface. Journal of Tribology, 119, 273-278.
http://doi.org/10.1115/1.2833188
[8]
Lee, C., Lin, C., Jian, R. and Wen, C. (2006) Simulation and Experimentation on the Contact Width and Pressure Distribution of Lip Seals. Tribology International, 39, 915-920. http://doi.org/10.1016/j.triboint.2005.09.002
[9]
Meyer, S., von Estorff, O., Feldmann, M. and Wollesen, V.M. (2006) Test on Rotary Sfaft Lip Type Seals and Finiite Element Simulation for Validation of Material Laws for Elastomers. 14th International Sealing Conference, Stuttgart, 10-11 October 2006, 522-533.
[10]
Plath, S., Meyer, S. and Wollesen, V.M. (2005) Friction Torque of a Rotary Shaft Seal Lip Type Seal—A Comparison between Test Results and Finite Element Simulation. Mechanika, 4, 55-59.
[11]
Daubner, A. and Haas, W. (2009) Simulation der Temperatur im und am Reibkontakt, Computational Fluid Dynamics. NAFEMS Magazine, 62-71.
[12]
Engelke, T. (2011) Friction Torque of a Rotary Shaft Lip Type Seal—A Comparison Between Test Results and Finite Element Simulation. Ph.D. Thesis, Gottfried Wilhelm Leibniz University Hannover, Hannover.
[13]
Deleau, F., Mazuyer, D. and Koenen A. (2009) Sliding Friction at Elastomer/Glass Contact: Influence of the Wetting Conditions and Instability Analysis. Tribology International, 42, 149-159. https://doi.org/10.1016/j.triboint.2008.04.012
[14]
Bódai, G. and Goda, T.J. (2014) Sliding Friction of Wiper Blade: Measurement, FE Modeling and Mixed Friction Simulation. Tribology International, 70, 63-74.
https://doi.org/10.1016/j.triboint.2013.07.013
[15]
El Gadari, M., Fatu, A and Hajjam, M. (2015) Shaft Roughness Effect on Elasto-Hydrodynamic Lubrication of Rotary Lip Seals: Experimentation and Numerical Simulation. Tribology International, 88, 218-227.
https://doi.org/10.1016/j.triboint.2015.03.013
[16]
El Gadari, M., Fatu, A. and Hajjam, M. (2016) Effect of Grooved Shaft on the Rotary Lip Seal Performance in Transient Condition: Elasto-Hydrodynamic Simulations. Tribology International, 93, 411-418. https://doi.org/10.1016/j.triboint.2015.09.031
[17]
Wenk, J.F., Stephens, L.S., Lattime, S.B and Weatherly, D. (2016) A Multi-Scale Finite Element Contact Model Using Measured Surface Roughness for a Radial Lip Seal. Tribology International, 97, 288-301.
https://doi.org/10.1016/j.triboint.2016.01.035
[18]
Szabó, Gy. and Váradi, K. (2017) Large Strain Viscoelastic Material Models for Deformation, Stress and Strain Analysis of O-Rings. Periodica Polytechnica (submitted).
[19]
Szabó, Gy. and Vádadi, K. (2017) Failure Mechanism of O-Ring Seals under Extreme Operating Conditions. Modern Mechanical Engineering, XXX, 121-120.
[20]
Márton, Z. (2011) Contact Behaviour of an Elastomeric Radial Shaft Seal (Budapest). MSc. Thesis, Budapest University of Technology and Economics, Budapest.
[21]
Szucs, P. (2014) Modellierung der Warmeentwicklung am mehrachsigen Dichtprüfapparat (Budapest). MSc. Thesis, Budapest University of Technology and Economics, Budapest.
[22]
ANSYS Inc. (2017) ANSYS Help 18.2. ANSYS Inc., Canonsburg.
[23]
Urzhumcev, Y.S. and Maximov, R.D. (1982) Prognostika deformativnosti polimernyh materialnov (Deformation Prognosis of Polymer Materials). Riga.
