Friction Stir Welding (FSW) is currently used in many aircraft and aerospace sheet metal structures involving lap joints and there has been growing interest in recent years in utilizing this process for joining aluminum alloys. In this paper, Friction Stir Lap Welding (FSLW) of the 6061-T6 aluminum alloy was carried out to obtain the optimum welding condition for maximum shear strength where the rotational speed, axial load, and welding speed were taken as process parameters. An L-9 orthogonal array, a Taguchi Method with consideration of three levels and three factors was designed and executed for conducting trials. Analysis of variance (ANOVA) and Signal to Noise (S/N) ratio were employed to investigate the influence of different welding parameters on the shear strength and obtain the optimum parameters. The Fisher-Test was also implemented to find the design parameter which had the most important effect on the characteristic of quality. The results indicated that the tool rotational speed had the maximum percentage contribution (51%) on the response (shear strength) followed by the welding speed (38%) and the axial load (8%) while the percentage of error was 3%. However, to confirm the main effects for the means and S/N ratios of the experiment, theoretical shear strength values were computed to predict the tensile strength. The maximum shear strength of 60 MPa was achieved and the effectiveness of the method was confirmed. The optimum parameter combinations that provided higher shear strength were: rotational speed of 1200 rpm, welding speed of 45 mm/min and the axial load of 11.5 kN.
References
[1]
Thomas, W.M., Nicholas, E.D., Needham, J.C., Murch, M.G., Templesmith, P. and Dawes, C.J. (1991) International Patent Application No. PCT/GB92/02203 and GB Patent Application No. 9125978.8.
[2]
Mishra, R.S. and Ma, Z.Y. (2005) Friction Stir Welding and Processing. Materials Science and Engineering: R: Reports, 50, 1-78.
https://doi.org/10.1016/j.mser.2005.07.001
[3]
Liu, G., Murr, L.E., Niou, C.S., McClure, J.C. and Vega, F.R. (1997) Microstructural Aspects of the Friction-Stir Welding of 6061-T6 Aluminum. Scripta Materialia, 37, 355-361. https://doi.org/10.1016/S1359-6462(97)00093-6
[4]
Rathinasuriyan, C., Kumar, V.S. and Shanbhag, A.G. (2014) Radiography and Corrosion Analysis of Sub-Merged Friction Stir Welding of AA6061-T6 Alloy. Procedia Engineering, 97, 810-818. https://doi.org/10.1016/j.proeng.2014.12.355
[5]
Sankar, R., Rathinasuriyan, C. and Senthil Kumar, V.S. (2017) Effect of Cooling Conditions on Mechanical and Microstructural Behaviours of Friction Stir Processed AZ31B Mg Alloy. Modern Mechanical Engineering, 7, 144-160.
https://doi.org/10.4236/mme.2017.74010
Dubourg, L., Merati, A. and Jahazi, M. (2010) Process Optimisation and Mechanical Properties of Friction Stir Lap Welds of 7075-T6 Stringers on 2024-T3 Skin. Materials & Design, 31, 3324-3330. https://doi.org/10.1016/j.matdes.2010.02.002
[9]
Chen, Y.C. and Nakata, K. (2008) Friction Stir Lap Joining Aluminum and Magnesium Alloys. Scripta Materialia, 58, 433-436.
https://doi.org/10.1016/j.scriptamat.2007.10.033
[10]
Cao, X. and Jahazi, M. (2011) Effect of Tool Rotational Speed and Probe Length on Lap Joint Quality of a Friction Stir Welded Magnesium Alloy. Materials & Design, 32, 1-11. https://doi.org/10.1016/j.matdes.2010.06.048
[11]
Saeid, T., Abdollah-Zadeh, A. and Sazgari, B. (2010) Weldability and Mechanical Properties of Dissimilar Aluminum-Copper Lap Joints Made by Friction Stir Welding. Journal of Alloys and Compounds, 490, 652-655.
https://doi.org/10.1016/j.jallcom.2009.10.127
[12]
Abdollah-Zadeh, A., Saeid, T. and Sazgari, B. (2008) Microstructural and Mechanical Properties of Friction Stir Welded Aluminum/Copper Lap Joints. Journal of alloys and Compounds, 460, 535-538. https://doi.org/10.1016/j.jallcom.2007.06.009
[13]
Kumar, B.A. and Murugan, N. (2014) Optimization of Friction Stir Welding Process Parameters to Maximize Tensile Strength of Stir Cast AA6061-T6/AlNp Composite. Materials & Design, 57, 383-393. https://doi.org/10.1016/j.matdes.2013.12.065
[14]
Lokesh, R., Kumar, V.S.S., Rathinasuriyan, C. and Sankar, R. (2015) Optimization of Process Parameters Tool Pin Profile, Rotational Speed and Welding Speed for Submerged Friction Stir Welding of AA6063 Alloy. International Journal of Technical and Research Applications, 12, 35-38.
[15]
Rathinasuriyan, C. and Kumar, V.S. (2016) Modelling and Optimization of Submerged Friction Stir Welding Parameters for AA6061-T6 Alloy Using RSM. Metallic Materials, 54, 297-304. https://doi.org/10.4149/km_2016_3_297
[16]
Babu, S., Sankar, V.S., Ram, G.J., Venkitakrishnan, P.V., Reddy, G.M. and Rao, K.P. (2013) Microstructures and Mechanical Properties of Friction Stir Spot Welded Aluminum Alloy AA2014. Journal of Materials Engineering and Performance, 22, 71-84. https://doi.org/10.1007/s11665-012-0218-z
[17]
Fonda, R.W. and Bingert, J.F. (2004) Microstructural Evolution in the Heat-Affected Zone of a Friction Stir Weld. Metallurgical and Materials Transactions A, 35, 1487-1499. https://doi.org/10.1007/s11661-004-0257-7
[18]
Elangovan, S., Prakasan, K. and Jaiganesh, V. (2010) Optimization of Ultrasonic Welding Parameters for Copper to Copper Joints Using Design of Experiments. The International Journal of Advanced Manufacturing Technology, 51, 163-171.
https://doi.org/10.1007/s00170-010-2627-1
[19]
Ross, P.J. (1996) Taguchi Techniques for Quality Engineering: Loss Function, Orthogonal Experiments, Parameter and Tolerance Design. McGraw–Hill Publishing Company Ltd., New York.
[20]
Bozkurt, Y. (2012) The Optimization of Friction Stir Welding Process Parameters to Achieve Maximum Tensile Strength in Polyethylene Sheets. Materials & Design, 35, 440-445. https://doi.org/10.1016/j.matdes.2011.09.008
[21]
Yang, W.P. and Tarng, Y.S. (1998) Design Optimization of Cutting Parameters for Turning Operations Based on the Taguchi Method. Journal of Materials Processing Technology, 84, 122-129. https://doi.org/10.1016/S0924-0136(98)00079-X
