Vertical Axis Wind Turbines (VAWTs) with fixed pitch blades have a limited power capture performance envelope as the Tip Speed Ratio (TSR) changes. Circulation Control (CC) has been proposed and simulated to possibly increase power capture of a VAWT using constant CC jet momentum, but a practical method of minimizing CC usage has yet to be explored. In addition, VAWTs are typically limited in power capture performance either by a maximum peak at a small set of TSR or wide operating TSR at fractions of the peak performance based on the design solidity. Both the reduced jet usage and solidity limitation were addressed by developing a method of dynamically using CC to perform a virtual solidity change. The developed method described within this work used CC to change blade aerodynamics to specifically match a maximum performing static solidity or wake shape at a given TSR. Simulation results using an existing aerodynamics model indicated a significant reduction in the re-quired CC jet momentum compared to a constant CC system along with control over power capture for a CC-VAWT.
References
[1]
Wiser, R. and Bolinger, M. (2007) Annual Report on U.S. Wind Power Installation, Cost, and Performance Trends. National Renewable Energy Laboratory Report, Denver.
[2]
Thresher, R., Robinson, M. and Veers, P. (2007) To Capture the Wind. IEEE Power & Energy Magazine, 7, 1540-7977. https://doi.org/10.1109/mpe.2007.906304
[3]
Pawsey, N. (2002) Development and Evaluation of Passive Variable-Pitch Vertical Axis Wind Turbines. PhD Dissertation, The University of New South Wales, Sydney.
[4]
Paraschivoiu, I., Trifu, O. and Saeed, F. (2009) H-Darrieus Wind Turbine with Blade Pitch Control. International Journal of Rotating Machinery, 2009, Article ID: 505343.
[5]
Wilhelm, J.P., Pertl, E.D., Pertl, F.A. and Smith, J.E. (2009) Performance Predictions of a Circulation Controlled-Vertical Axis Wind Turbine with Solidity Control. ASME 2009 3rd International Conference on Energy Sustainability collocated with the Heat Transfer and InterPACK09 Conferences, San Francisco, 19-23 July 2009, 1001-1007. https://doi.org/10.1115/es2009-90350
[6]
Wilhelm, J.P., Panther, C.C., Pertl, F.A. and Smith, J.E. (2009) Vortex Analytical Model of a Circulation Controlled Vertical Axis Wind Turbine. ASME 2009 3rd International Conference on Energy Sustainability Collocated with the Heat Transfer and InterPACK09 Conferences, San Francisco, 19-23 July 2009, 993-1000. https://doi.org/10.1115/es2009-90348
[7]
Van Dam, C., Berg, D.E. and Johnson, S.J. (2008) Active Load Control Techniques for Wind Turbines. Sandia National Laboratories, Albuquerque. https://doi.org/10.2172/943932
[8]
AslamBhutta, M.M., Hayat, N. Farooq, A.U., Ali, Z., Jamil, S.R. and Hussain, Z. (2012) Vertical Axis Wind Turbine—A Review of Various Configurations and Design Techniques. Renewable and Sustainable Energy Reviews, 16, 1926-1939.
[9]
Samsonov, V. and Baklushin, P. (1992) Comparison of Different Ways for VAWT Aerodynamic Control. Journal of Wind Engineering and Industrial Aerodynamics, 39, 427-433.
[10]
Lazauskas, L. (1992) Three Pitch Control Systems for Vertical Axis Wind Turbines Compared. Wind Engineering, 16, 269-282.
[11]
Hwang, I.S., Min, S.Y., Jeong, I.O., Lee, Y.H. and Kim, S.J. (2006) Efficiency Improvement of a New Vertical Axis Wind Turbine by Individual Active Control of Blade Motion. Smart Structures and Materials, 6173, 316-323.
[12]
Greenblatt, D., Schulman, M. and Ben-Harav, A. (2012) Vertical Axis Wind Turbine Performance Enhancement Using Plasma Actuators. Renewable Energy, 37, 345-354.
[13]
Owen, F.K. and Owen, A.K. (2006) Measurement and Analysis of Circulation Control Airfoils. Applications of Circulation Control Technology, Progress in Astronautics and Aeronautics, 214, 105-112.
[14]
Yen, J. and Ahmed, N.A. (2013) Enhancing Vertical Axis Wind Turbine by Dynamic Stall Control Using Synthetic Jets. Journal of Wind Engineering and Industrial Aerodynamics, 114, 12-17.
[15]
Panther, C.C., Williams, K.A., Wilhelm, J.P. and Smith, J.E. (2010) Experimental Testing of a Wind Tunnel Model for Use in a Vertical Axis Wind Turbine. Proceedings of the ASME 2010 International Mechanical Engineering Congress and Exposition. Vancouver, 12-18 November 2010, 153-161. https://doi.org/10.1115/imece2010-38816
[16]
Shires, A. and Kourkoulis, V. (2013) Application of Circulation Controlled Blades for Vertical Axis Wind Turbines. Energies, 6, 3744-3763. https://doi.org/10.3390/en6083744
[17]
Lubert, C. (2011) On Some Recent Applications of the Coanda Effect. International Journal of Acoustics and Vibration, 16, 144. https://doi.org/10.20855/ijav.2011.16.3286
[18]
Abramson, J. (1984) Low-Speed Characteristics of a Circulation Control Airfoil with Aft Camber and a Spiral Trailing Edge. DTIC Document, Technical Report.
[19]
Jones, G.S. and Englar, R.J. (2003) Advances in Pneumatic-Controlled High-Lift Systems through Pulsed Blowing. AIAA 21st Applied Aerodynamics Conference, Orlando, 23-26 June 2003, 3411.
[20]
Englar, R.L.L. (1975) Circulation Control for High Lift and Drag Generation on STOL Aircraft. Journal of Aircraft, 12, 457-463. https://doi.org/10.2514/3.59824
[21]
Haus, F. (1931) The Use of Slots for Increasing the Lift of Airplane Wings. Technical Memorandum, National Advisory Council for Aeronautics.
[22]
Englar, R.J. and Huson, G. (1984) Development of Advanced Circulation Control Wing High-Lift Airfoils. Journal of Aircraft, 21, 476-483. https://doi.org/10.2514/3.44996
[23]
Kweder, J., Panther, C.C. and Smith, J.E. (2010) Applications of Circulation Control, Yesterday And Today. International Journal of Engineering, 4, 411-429.
[24]
Wolfe, W.P. (1978) Analysis of Test Results for the WVU Straight Bladed Darrieus wind Turbine. PhD Dissertation, West Virginia University, Morgantown.
[25]
McGrain, D., Angle, G.M., Wilhelm, J.P., Pertl, E.D. and Smith, J.E. (2009) Circulation Control Applied to Wind Turbines. ASME 2009 3rd International Conference on Energy Sustainability Collocated with the Heat Transfer and InterPACK09 Conferences, San Francisco, 19-23 July 2009, 905-910.
[26]
Graham, H.Z., Hubbell, M., Panther, C., Wilhelm, J.P., Angle, G.M. and Smith, J.E. (2009) Circulation Controlled Airfoil Analysis through 360 Degrees Angle of Attack. ASME 2009 3rd International Conference on Energy Sustainability collocated with the Heat Transfer and InterPACK09 Conferences, San Francisco, 19-23 July 2009, 571-577.
[27]
Tangler, J.L. (2000) The Evolution of Rotor and Blade Design. National Renewable Energy Laboratory, Golden.
[28]
Bianchi, F.D., De Battista, H. and Mantz, R.J. (2006) Wind Turbine Control Systems: Principles, Modelling and Gain Scheduling Design. Springer Science & Business Media, London.
[29]
Castelli, M.R., Englaro, A. and Benini, E. (2011) The Darrieus Wind Turbine: Proposal for a New Performance Prediction Model Based on CFD. Energy, 36, 4919- 4934. https://doi.org/10.1016/j.energy.2011.05.036
[30]
Migliore, P.G. (1979) A Free-Vortex Model with Numerical Solution for the Unsteady Lifting Characteristics of Straight Bladed Darrieus Wind Turbines. PhD Dissertation, West Virginia University, Morgantown.
[31]
Walters, R.E., Fanucci, J., Loth, J., Ness, N. and Palmer, G. (1975) Innovative Wind Machines. Technical Report, 76, 33677.
[32]
Scheurich, F., Fletcher, T.M. and Brown, R.E. (2011) Simulating the Aerodynamic Performance and Wake Dynamics of a Vertical-Axis Wind Turbine. Wind Energy, 14, 159-177. https://doi.org/10.1002/we.409
[33]
Wilhelm, J.P., Nawrocki, A., Hard, S. and Smith, J.E. (2010) Controller Design Methodology for a Circulation Controlled Vertical Axis Wind Turbine. Proceedings of 28th AIAA Applied Aerodynamics Conference, Chicago, 28 June-1 July 2010, 2010- 4405. https://doi.org/10.2514/6.2010-4405
[34]
Roh, S.C. and Kang, S.H. (2013) Effects of a Blade Profile, the Reynolds Number, and the Solidity on the Performance of a Straight Bladed Vertical Axis Wind Turbine. Journal of Mechanical Science and Technology, 27, 3299-3307. https://doi.org/10.1007/s12206-013-0852-x
