VAN BARSCHOT J. Airbus en boeing vliegen met ten cate[N]. NRC Handelsblad, Rotterdam, 2005-01-05(17).
[2]
PATRICIA P P, HARALD E N B, BEUKERS A. Residual stresses in thermoplastic composites-a study of the literature-part Ⅰ: formation of residual stesses[J]. Composites: Part A: Applied Science Manufacturing, 2006, 37(11):1847-1857.
[3]
LAMONTIA M A, GRUBER M B, TIERNEY J J, et al. Modeling the accudyne thermoplastic in situ ATP process[A]. 30th International SAMPE Europe Conference[C], Paris: SAMPE, 2009.
ARONSON R. Composites offer more opportunities manufacturing[J]．Engineering, 2005, 135(2):75－83．
[6]
LI Yue-hua, FU Hong-ya, SHAO Zhong-xi. The influence of preheating on automated fiber placement speed[A]. Advanced Materials Research[C]. Switzerland, Trans Tech Publications, 2011. 213: 136-142.
[7]
GHASEMI NEJHAD M N. Three-dimensional thermal and residual stress analysis of in-situ thermoplastic composite filament winding[D]. Department of Mechanical Engineering, University of Delaware, Newark, Delaware, 1992.
[8]
GHASEMI NEJHAD M N. Thermal analysis for thermoplastic composite tow/tape preheating and pultrusion[J]. Journal of Thermoplastic Composite Materials, 1997, 10(6): 504-523.
[9]
KLASUS D F, KARL V S. A new compact robotic head for thermoplastic fiber placement[A]. 38th SAMPE Symposium[C], Paris: SAMPE, 1993.138-151.
[10]
SHIH P J. On-line consolidation of thermoplastic composites[D]. Department of Mechanical Engineering, Virginia Polytechnic Institute and State University, Virginia, Blacksburg, 1997.
[11]
COLTON J, LEACH D. Processing parameters for filament winding thick-section PEEK/carbon fiber composites[J]. Polymer Composites, 1992, 13(6): 427-434.
[12]
PITCHUMANI R, DON R C, GILLESPIE J W, et al. Analysis of on-line consolidation during thermoplastic tow-placement process[J]. Thermal Processing of Materials, 1994, 289: 223-239.
[13]
GROVE S M. Thermal modeling of tape laying with continuous carbon fiber-reinforced thermoplastic. Composites[J], 1988, 19(2): 367-375.
[14]
GHASEMI NEJHAD M N, COPE R D, G?CERI S I. Thermal analysis of in situ thermoplastic composite tape laying[J]. Journal of Thermoplastic Composite Materials, 1991, 4(1): 20-45.
[15]
TURNKOR S, TURKMEN N, CHASSAPIS C, et al. Modeling of heat transfer in thermoplastic composite tape lay-up manufacturing[J]. Heat Mass Transfer, 2001, 28(1): 49-58.
[16]
JANDAL M Z, WIDMANN G. 热分析应用手册系列丛书：热塑性聚合物[M]. 上海:东华大学出版社,2008.1-20.
[17]
金日光, 华幼卿. 高分子物理[M]. 北京:化学工业出版社, 2007.80-110.
[18]
TIERNEY J J, GILLESPIE J W Jr. Crystallization kinetics behavior of PEEK based composites exposed to high heating and cooling rates[J]. Composites: Part A : Applied Science Manufacturing, 2004, 35(5): 547-558.
[19]
BOUTAOUS M, BRAHMIA N, BOURGIN P. Parametric study of the crystallization kinetics of a semi-crystalline polymer during cooling[J]. Comptes Rendus Mecanique, 2010, 338(2): 78-84.
[20]
TIERNEY J J, GILLESPIE J W Jr. Modeling of situ strength development for the thermoplastic composite tow placement process[J]. Journal of Composite Materials, 2006, 40(16): 1487-1506.
[21]
DARA P H, LOOS A C. Thermoplastic matrix composite processing model[R].Virginia Polytechnic Institute and State University, Virginia, Blacksburg, 1985.
[22]
LEE W I, SPRINGER G S. A model for the manufacturing process of thermoplastic matrix composites[J]. Composite Materials, 1987, 21(11): 1017—1987.
[23]
MANTELL S C, SPRINGER G S. Manufacturing process models for thermoplastic composites[J].Composite Materials, 1992, 26(16): 2348-2377.
[24]
DE GENNES P. Reptation of a polymer chain in the presence of fixed obstacles[J].Chemical Physics, 1971, 55(2): 572-579.
[25]
DOI M, EDWARDS S F. Dynamics of concentrated polymer systems[J].Faraday Transactions, 1978, 74(1): 1789-1801.
[26]
YANG F, PITCHUMANI R. Healing of thermoplastic polymers at the interface under nonisothermal conditions[J]. Macromolecules, 2002, 35(8): 3213-3224.
[27]
PARLEVLIET P P, BERSEE H E N, BEUKERS A. Residual stresses in thermoplastic composites-a study of the literature-part Ⅱ: experimental techniques[J]. Composites Part A: Applied Science Manufacturing, 2006, 37(3): 651-665.
[28]
PARLEVLIET P P, BERSEE H E N, BEUKERS A. Residual stresses in thermoplastic composites-a study of the literature-part Ⅲ: effects of thermal residual stresses[J]. Composites Part A: Applied Science Manufacturing, 2006, 37(6): 1581-1596
MOREY B. Automating composites fabrication[J]．Manufacturing Engineering, 2008, 140(4): 12-16．
[31]
LEE M. Heat transfer and consolidation modeling of composite fiber tow in fiber placement[D]. Department of Mechanical Engineering, Virginia Polytechnic Institute and State University, Virginia, Blacksburg, 2004.
[32]
BASTIEN L J, CILLESPIE J W Jr. A nonisothermal healing model for strength and toughness of fusion bonded joints of amorphous thermoplastics[J]. Polymer Engineering and Science, 1991, 31(24):1720-1730.
