OALib Journal期刊
Al-6.3Zn-2.8Mg-1.8Cu铸造铝合金的组织和室温力学性能
DOI: 10.3724/SP.J.1037.2011.00579
Keywords: 铝合金 ,固溶处理 ,显微组织 ,时效硬化 ,力学性能
Abstract:
研究了Al-6.3Zn-2.8Mg-1.8Cu铸造铝合金的组织和室温力学性能.研究表明,在金属型铸造条件下,Al-6.3Zn-2.8Mg-1.8Cu合金的铸态组织为近等轴晶,相组成为α(Al)基体、枝晶间α(Al)+η(MgZn2)共晶、晶内游离η相(MgZn2)、少量T相(Mg3ZnxCu3-xAl2)及少量颗粒状Al7Cu2Fe.固溶处理后,原铸态组织中的η(MgZn$_{2}$)相大部分溶解消失,但形成新的沿晶界分布的S相(Al2CuMg).实验确定了固溶态Al-6.3Zn-2.8Mg-1.8Cu合金较优的单级和双级时效工艺.与单级时效工艺相比,采用双级时效工艺处理后,抗拉强度由480MPa增加至490MPa,延伸率由0.2%增加至2.2%.
References
[1] Srivatsan T S. J Mater Sci, 1992; 27: 4772 [2] Zakharov V V, Rostova T D. Met Sci Heat Treat, 1995; 37(5-6): 203 [3] Mukhopadhyay A K, Reddy G M, Prasad K S, Varma V K, Mondac C. In: Nie J F, Morton A J, Muddle B C, eds., Proc 9th Int Conf on Aluminium Alloys, Australia: Institute [4] Wang H B, Huang J F, Yang B, Zhang J S, Zhang Y A, Xiong B Q. Mater Rev, 2003; 17(9): 1 [5] (王洪斌, 黄进峰, 杨滨, 张济山, 张永安, 熊柏青. 材料导报, 2003; 17(9): 1) [6] (陈昌麒. 中国有色金属学报, 2002; 12(3): 22) [7] Chen K H, Liu H W, Zhang Z, Li S, Todd R I. J Mater Process Technol, 2003; 142: 190 [8] Mondal C, Mukhopadhyay A K. Mater Sci Eng, 2005; A391: 367 [9] Xie F Y, Yan X Y, Ding L, Zhang F, Chen S L, Chu M G, Chang Y A. Mater Sci Eng, 2003; A355: 144 [10] Manish D D. PhD Thesis, Georgia Institute of Technology, 2000 [11] Fan X G. PhD Thesis, Harbin Institute of Technology, 2007 [12] (樊喜刚. 哈尔滨工业大学博士学位论文, 2007) [13] Fan X G, Jiang D M, Meng Q C, Zhong L. Mater Lett, 2006; 60: 1475 [14] Starink M J, Wang S C. Acta Mater, 2003; 51: 5131 [15] Poole W J, S？ter J A, Skjervold S, Watercoo G. Metall Mater Trans, 2000; 31A: 2327 [16] Starink M J, Li X M. Metall Mater Trans, 2003; 34A: 899 [17] You W, Lin S Y. Alum Fabr, 1999; 22(1): 4 [18] (游文, 林顺岩. 铝加工, 1999; 22(1): 4) [19] Si N C, Fu M X. Nonferrous Metal Material and Preparation. Beijing: Chemical Industry Press, 2006: 36 [20] (司乃潮, 傅明喜. 有色金属材料及制备. 北京: 化学工业出版社, 2006: 36) [21] Li Y Y, Guo GW, Luo Z Q, Long Y. Spec Cast Nonferrous Alloys, 2000; 6: 45 [22] Li N K, Cui J Z. Light Alloy Fabr Technol, 2008; 36(1): 5 [23] (丁惠麟, 辛智华. 实用铝、铜及其合金金相热处理和失效分析. 北京: 机械工业出版社, 2008: 102) [24] Lu S S, Gu K D, Zheng L S. Nonferrous Casting Alloys and Melting. Beijing: National Defense Industry Press, 1983: 52 [25] (陆树荪, 顾开道, 郑来苏. 有色铸造合金及熔炼. 北京: 国防工业出版社, 1983: 52) [26] Heinz A, Haszler A, Keidel C, Moldenhauer S. Mater Sci Eng, 2000; A280: 102 [27] of Materials Engineering Australia Ltd, 2004: 883 [28] Chen C Q. Chin J Nonferrour Met, 2002; 12(3): 22 [29] (李元元, 郭国文, 罗宗强, 龙雁. 特种铸造及有色合金, 2000; 6: 45) [30] (李念奎, 崔建忠. 轻合金加工技术, 2008; 36(1): 5) [31] Zhang B C. Nonferrous Metal and Heat-treatment. Xi’an: NWPU Industry Press, 1993: 62 [32] (张宝昌. 有色金属及其热处理. 西安: 西北工业大学出版社, 1993: 62) [33] Sheppard T. Extrusion of Aluminium Alloy. London: Kluwer Academic Publisher, 1999: 23 [34] Alekseev A A, Fridlyander I N, Berg L B. Mater Sci Forum, 2002; 396-342: 821 [35] Rokhlin L L, Dobatkina T V, Bochvar N R, Lysova E V. J Alloys Compd, 2004; 367: 10 [36] Metallographic Atlas Compilation Group. Wrought Aluminum Alloy Metallographic Atlas. Beijing: Metallurgical Industry Press, 1975: 157 [37] (金相图谱编写组. 变形铝合金金相图谱. 北京: 冶金工业出版, 1975: 157) [38] Ding H L, Xin Z H. Practical Aluminum, Copper and Its Alloys Heat Treatment and Metallurgical Failure Analysis. Beijing: Machinery Industry Press, 2008: 102
Full-Text
Contact Us
service@oalib.com
QQ:3279437679
WhatsApp +8615387084133
