OALib Journal期刊
多道次热轧对包层钢筋性能及结合面的影响
DOI: 10.3724/SP.J.1037.2011.00364
Keywords: 包层钢筋 ,热轧 ,结合界面 ,扩散
Abstract:
采用热轧的方式制备了不锈钢/碳钢包层钢筋,研究了包层钢筋的机械性能及界面的结合情况.通过拉伸、剪切实验测试了钢筋的抗拉强度等性能及两金属的结合强度.应用OM,SEM,EDS以及显微硬度仪对界面附近的显微形貌、元素扩散以及显微硬度分布进行分析.实验结果显示不锈钢/碳钢包层钢筋的轧制过程中双金属等比例延伸,其抗拉强度高达550MPa,延伸率45%,拉伸过程中出现明显缩颈,断口处两金属未分离.随轧制道次的增加,金属结合更加致密,剪切强度增加,最大剪切强度为333MPa,剪切断裂面出现典型的塑性韧窝和剪切滑移.界面附近出现了明显的元素扩散,不锈钢中的Cr,Mn和Ni等元素向碳钢扩散,碳钢中的Fe元素向不锈钢扩散,总扩散距离约30μm,造成界面附近碳钢侧的显微硬度显著增大,第6道次后其值为399.4HV,远高于碳钢基体的硬度.复合包层钢筋界面间形成了良好的冶金扩散结合.
References
[1] Hwang Y M, Hsu H H, Hwang Y L. Int J Mech Sci, 2000; 42: 2417 [2] Kang H, Kim J, Huh M, Engler O. Mater Sci Eng, 2007; A452-453: 347 [3] Lee J, Bae D, Chung W, Kim K, Cho Y. J Mater Process Technol, 2007; 187-188: 546 [4] Soltanalinezhad M, Haerianardakani A. Mater Des, 2009; 30: 1103 [5] Zhang L, Meng L, Zhou S P, Yang F T. Mater Sci Eng, 2004; A371: 65 [6] Bulent K. J Mater Process Technol, 2007; 190: 138 [7] Motarjemi A K, Korcak M, Ventzke V. Int J Pres Ves Pip, 2002; 79: 181 [8] Li S X, Xuan F Z, Tu S T. J Nucl Mater, 2007; 366(1/2): 1 [9] Madaah-Hosseini H R, Kokabi A H. Mater Sci Eng, 2002; A335: 186 [10] Kundu S, Chatterjee S. Mater Sci Eng, 2006; A425(1/2): 107 [11] He P, Yue X, Zhang J. Mater Sci Eng, 2008; A486: 171 [12] Elrefaey A, Tillmann W. J Mater Process Technol, 2009; 209: 2746 [13] Wu C J, Wu Y, Xue Z Y, Liang H, Liu Q. Acta Metall Sin (Engl Lett), 2010; 23: 206 [14] Lesik L, Dyja H, Pilarczyk J W, Wiewiorowska S. Wire J Int, 2001; 34(2): 94 [15] Dyja H, Lesik L, Milenin A, Mroz S. J Mater Process Technol, 2002; 125-126: 731 [16] Berski S, Dyja H, Maranda A, Nowaczewski J, Banaszek G. J Mater Process Technol, 2006; 177: 582 [17] Manesh H, Taheri A. J Mater Process Technol, 2005; 166: 163 [18] Yuan J W, Pang Y H, Li T. J Wuhan Univ Technol, 2011; 26: 111 [19] Dyja H, Mroz S, Milenin A, Lesik L. In: International Rolling Conference ed., 44th MWSP Conference Proceeding, Orlando: Association for Iron & Steel, 2002: 40: 653 [20] Dyja H, Mroz S, Stradomski Z. Metalurgija, 2003; 42(3): 185 [21] Dyja H, Mroz S, Milenin A. J Mater Process Technol, 2004; 153-154: 100 [22] Szota P, Dyja H. J AMME, 2007; 25(1): 55 [23] Mroz S, Szota P, Dyja H, Kawalek A. Metalurgija, 2011; 50(2): 85 [24] Ricardo R. Master Dissertation, Massachusetts Institute of Technology, Cambridge, 2001 [25] Purk Y. Master Dissertation, North Carolina State University, Raleigh, 2003 [26] Gregory W. PhD Thesis, Virginia Polytechnic Institute and State University, Blacksburg, 2007
Full-Text
Contact Us
service@oalib.com
QQ:3279437679
WhatsApp +8615387084133
