陈绍文,陈浮,王可立,等．采用弯叶片的不同折转角压气机叶栅流场气动性能[J]．推进技术,2007,28(3)：170-175．Chen Shaowen,Chen Fu,Wang Keli,et al．Aerodynamic performance study of curved compressor cascades with different camber angles[J]．Journal of Propulsion Technology,2007,28(3)：170-175(in Chinese)．
[2]
Abdallah H,Harvey H．Thermodynamic analysis of chemically recuperated gas turbines[J]．International Journal of Thermal Sciences,2001,40(4)：372-383．
[3]
刘勋,周逊,温风波,等．F级中低热值燃料燃气轮机透平部分气动方案优化设计与分析[J]．中国电机工程学报,2011,31(26)：1-8．Liu Xun,Zhou Xun,Wen Feng bo,et al．Aerodynamic optimization design and analysis on the turbine part of F class gas turbine under middle and low heat value fuel[J]．Proceedings of the CSEE,2011,31(26)：1-8(in Chinese)．
[4]
蔡乐,杜鑫,王松涛,等．某重型燃气轮机压气机顶切方法的数值模拟[J]．中国电机工程学报,2012,32(32)：95-100．Cai Le,Du Xin,Wang Songtao,et al．Numerical simulation analysis of the tip-cutting method in a compressor of a heavy duty gas turbine[J]．Proceedings of the CSEE,2012,32(32)：95-100(in Chinese)．
[5]
陈冶,张宏涛．地面重型燃气轮机压气机静叶流动分析[J]．汽轮机技术,2010,52(3)：202-204．Chen Ye,Zhang Hongtao．Flow analysis of stationary blades for floor type heavy duty gas turbine compressor [J]．Turbine Technology,2010,52(3)：202-204(in Chinese)．
[6]
Du X,Wang S T and Wang Z Q．Study on the effect of End-bend cantilevered stator in a 2-stage axial compressor [J]．Journal of Thermal and Science,2009,18(2)：119-125．
[7]
杜鑫,王松涛,王仲奇,等．端弯联合弯叶片对扩压叶栅角区分离影响研究[J]．工程热物理学报,2012,33(10): 1687-1690(in Chinese)．Du Xin,Wang Songtao,Wang Zhongqi,et al．Effects of endbend-bowed blade on corner separation of a diffusion cascade[J]．Journal of Engineering Thermophysics,2012,33(10)：1687-1690(in Chinese)．
[8]
Breugelmans F A E．Influence of incidence angle on the secondary flow in compressor cascade with different dihedral distribution[C]// ISABE,Beijing,China,1985．
[9]
Bogod A B,Kimasov Y I,Mitrokhin V I,et al．Direct and inverted calculation of 2D axisymmetric and 3D flows in axial compressor blade rows[J] ．RFM,Revue Francaise de Mecanique,1992(4)：351-359．
[10]
Fischer A,Riess W,Seume J R．Performance of strongly bowed stators in a 4-stage high speed compressor[C]// IGTI ASME Turbo Expo,Atlanta,USA,2003．
[11]
Takahashi Y,Hamatake H ,Katoh Y．Experimental and numerical investigations of endwall flow in a bowed compressor cascade[C]//AIAA/ASM/SAE/ASEE Join Propulsion,Tucson,USA,2005．
[12]
钟兢军．弯曲叶片控制扩压叶栅二次流动损失的实验研究[D]．哈尔滨：哈尔滨工业大学,1995． Zhong Jingjun．An experimental investigation by using curved blade to control secondary flow in compressor cascade[D]．Harbin：Harbin Institute of Technology,1995(in Chinese)．
[13]
张华良．采用叶片弯/掠及附面层抽吸控制扩压叶栅内涡结构的研究[D]．哈尔滨：哈尔滨工业大学,2007． Zhong Hualiang．Investigation on application of dihedral/swept blade and boundary layer suction to control vortex configurations in compressor cascades [D]．Harbin：Harbin Institute of Technology,2007(in Chinese)．
[14]
Wellborn S R,Robert A D．Redesign of a 12-stage axial-flow compressor using multistage CFD[C]//IGTI ASME Turbo Expo,New Orleans,USA,2001．
[15]
Peng Z Y,Wu G,Yan M．An Experimental investigation of technologies of endwall flow control in a compressor plane cascade[C]//AIAA/ASM/SAE/ASEE Join Propulsion,Sacramento,USA,1991．
[16]
Peng Z Y,Wu G,Yan M．An experimental investigation of end-sweep cascade in a compressor plane cascade wind tunnel[C]//AIAA/ASM/SAE/ASEE Join Propulsion,Monterey,USA,1993．
[17]
Peng Z Y,Li R Y．End wall flow control in multistage axial flow compressor[C]//AIAA/ASM/SAE/ASEE Join Propulsion,Indianapolis,USA,1994．
[18]
黄力希,魏星禄,彭泽琰．叶片端弯技术机理探讨[J]．航空动力学报,1988,3(3)：220-222．Huang Lixi,Wei Xinglu,Peng Zeyan．Approach to blade end-bend mechanism[J]．Journal of Aerospace Power,1988,3(3)：220-222(in Chinese)．
