夏禹. 涡轮叶片造型CAD系统研究[D].西安:西北工业大学,2004 Xia Yu.The research on turbine blade CAD modeling system[D].Xi'an:Northwestern Polytechnical University,2004(in Chinese)
[2]
宋田庆, 莫蓉,夏禹,等.航空发动机叶片CAD造型方法[J].航空制造技术,2007(2):78-81 Song Tianqing,Mo Rong,Xia Yu,et al.CAD modeling method for aeroengine blade[J].Aeronautical Manufacturing Technology,2007(2):78-81(in Chinese)
[3]
航空发动机设计手册总编委会. 航空发动机手册第十册[M].北京:航空工业出版社,2000:8-9 Editorial Board of Aircraft Engine Design Manual.Aircraft engine design manual volume 10[M].Beijing:Aviation Industry Press,2000:8-9(in Chinese)
[4]
Hoschek J, Müller R.Turbine blade design by lofted B-spline surfaces[J].Journal of Computational and Applied Mathematics,2000,119(1/2):235-248
[5]
朱谦,宁涛, 席平.基于引导线的涡轮气冷叶片伸根建模方法[J].北京航空航天大学学报，2012,38(8):1085-1089 Zhu Qian,Ning Tao,Xi Ping.Root extending section of turbine modeling method based on guide curves[J].Journal of Beijing University of Aeronauties and Astronautics,2012,38(8): 1085-1089(in Chinese)
[6]
席平,朱谦, 张宝源.涡轮叶片冷气通道转接段的特征分析及建模[J].图学学报,2012,33(4):37-41 Xi Ping,Zhu Qian,Zhang Baoyuan.Feature analysis and modeling of cooling passages transition section in turbine blade[J].Journal of Graphics,2012,33(4):37-41( in Chinese)
[7]
倪萌,朱惠人, 裘云,等.航空发动机涡轮叶片冷却技术综述[J].燃气轮机技术.2005,18(4):25-33 Ni Meng,Zhu Huiren,Qiu Yun,et al.Review of aero-turbine blade cooling technologies[J].Gas Turbine Technology,2005,18(4):25-33(in Chinese)
[8]
Piegl L A, Tiller W.Computing offsets of NURBS curves and surfaces[J].Computer-Aided Design,1999,31(2):147-156
[9]
Ekkad S V, Pamula G,Shantiniketanam M.Detailed heat transfer measurements inside straight and tapered two-pass channels with rib turbulators[J].Experimental Thermal and Fluid Science,2000,22(3/4):155-163
[10]
宋田庆, 莫蓉,夏禹,等.航空发动机叶片CAD造型方法[J].航空制造技术,2007(2):78-81 Song Tianqing,Mo Rong,Xia Yu,et al.CAD modeling method for aeroengine blade[J].Aeronautical Manufacturing Technology,2007(2):78-81(in Chinese)
[11]
Hoschek J, Müller R.Turbine blade design by lofted B-spline surfaces[J].Journal of Computational and Applied Mathematics,2000,119(1/2):235-248
[12]
朱谦,宁涛, 席平.基于引导线的涡轮气冷叶片伸根建模方法[J].北京航空航天大学学报，2012,38(8):1085-1089 Zhu Qian,Ning Tao,Xi Ping.Root extending section of turbine modeling method based on guide curves[J].Journal of Beijing University of Aeronauties and Astronautics,2012,38(8): 1085-1089(in Chinese)
[13]
席平,朱谦, 张宝源.涡轮叶片冷气通道转接段的特征分析及建模[J].图学学报,2012,33(4):37-41 Xi Ping,Zhu Qian,Zhang Baoyuan.Feature analysis and modeling of cooling passages transition section in turbine blade[J].Journal of Graphics,2012,33(4):37-41( in Chinese)
[14]
Piegl L A, Tiller W.Computing offsets of NURBS curves and surfaces[J].Computer-Aided Design,1999,31(2):147-156
