|
|
- 2015
VIMP中结构拐角对纤维预成型体渗透特性的影响
|
Abstract:
采用真空导入模塑工艺(VIMP)制备纤维增强聚合物基复合材料多墙结构件时, 多墙体拐角处的纤维弯曲变形可能导致多墙体局部渗透特性发生变化。通过可视化流动实验考察了拐角对多墙体渗透特性和树脂流动行为的影响。结果表明: 无论是否使用导流介质, 多墙体中的拐角对树脂流体在VIMP灌注过程中都具有局部阻力作用, 降低了树脂充模流动速度和多墙体整体表观渗透率, 即存在拐角效应;拐角处铺放导流介质能有效降低拐角效应;随着拐角到注胶口的距离增大, 整体表观渗透率表现为先下降后上升。 In the manufacture of multi-walled composite structures with fiber reinforced polymer composites by the vacuum infusion molding process (VIMP), the local multi-walled permeability is changed at the corners of multi-walled structure due to the fiber bending deformation. The effects of corner on multi-walled permeability and resin flow behavior were investigated by the visual flow experiments. The results show that, regardless of the application of distribution medium, the resin molding flow rate and overall multi-walled apparent permeability would be decreased due to the corner effect. This behavior is ascribed to the local resistance effect of the corners applied to the resin in filling process of VIMP. The corner effect can be weakened through applying distribution medium to the corners. When the distance between the corner location and the injection gate becomes larger, the overall apparent permeability will decrease first, and then increase. 国家"863"计划(2012AA03A205); 国家自然科学基金(51303208); 湖南省重大科技专项(2011FJ1001)
| [1] | Yang J S. Study on resin flow behavior in vacuum infusion molding process[D].Changsha: National University of Defense Technology, 2007 (in Chinese). 杨金水.真空导入模塑工艺树脂流动行为研究[D]. 长沙: 国防科学技术大学, 2007. |
| [2] | Luo C Y, Xiong J J, Yi X S, et al. Natural modal and stability of integrated composite wing box fabricated by RTM process[J]. Acta Materiae Compositae Sinica, 2012, 29(3): 158-166(in Chinese). 罗楚养, 熊峻江, 益小苏, 等. RTM整体成型复合材料翼盒的固有模态及稳定性[J]. 复合材料学报, 2012, 29(3): 158-166. |
| [3] | Yang J S. Study on VIMP manufacturing and performance for thick-section carbon fiber composite[D]. Changsha: National University of Defense Technology, 2012 (in Chinese). 杨金水. 厚截面碳纤维复合材料VIMP制备与性能研究[D]. 长沙: 国防科学技术大学, 2012. |
| [4] | Chen P, Duan Y X, Liang Z Y. Research on the statistical model for the longitudinal permeability of preform[J]. Acta Materiae Compositae Sinica, 2004, 21(2): 105-110 (in Chinese). 陈鹏, 段跃新, 梁志勇. 预成型体纵向渗透率统计模型[J]. 复合材料学报, 2004, 21(2): 105-110. |
| [5] | Su F, Yu Y, Yu B F. Innovative improvement of vacuum assistant resin infusion process(VARI)[J]. Fiber Composites, 2010, 27(1): 18-20 (in Chinese). 苏峰, 于洋, 于柏峰. 真空辅助树脂灌注工艺的创新性改进[J]. 纤维复合材料, 2010, 27(1): 18-20. |
| [6] | Afendi M D, Banks W M, Kirkwood D. Bubble free resin for infusion process[J]. Composites Part A: Applied Science and Manufacturing, 2005, 36(6): 739-746. |
| [7] | Sun S, Liu M J, Wang H, et al. RTM molding process and its derive technology[J]. Aerospace Materials ＆ Technology, 2010, 40(6): 21-23 (in Chinese). 孙赛, 刘木金, 王海, 等. RTM成型工艺及其派生工艺[J].宇航材料工艺, 2010, 40(6): 21-23. |
| [8] | Andersson M, Lundstrom S, Gebart B R, et al. Development of guidelines for the vacuum infusion process[C]//Proceedings of the 8th International Conference on Fibre Reinforced Composites. Cambridge: Woodhead Publishing Materials, 2000: 113. |
| [9] | Lewit S M, Jakubowski J C. Low cost VARTM process for commercial and military applications [J]. Society for the Advancement of Material and Process Engineering,1997, 42(2): 1173-1187. |
| [10] | Riqas E J, Walsh S M, Spurgeon W. Development of a novel processing technique for vacuum assisted resin transfer molding(VARTM)[C]//46th International SAMPE Symposium and Exhibition Proceedings. New York: Technomic Publishing Co., Inc, 2001: 1086-1094. |
| [11] | Pike T, McArthur M, Schade D. Vacuum assisted resin transfer molding of a layered structural laminate for application on ground combat vehicles[J]. Technology Transfer in a Global Community, 1996, 28(4): 374-380. |
| [12] | Lin J Z, Ruan X D, Chen B G, et al. Fluid mechanics[M]. Beijing: Tsinghua University Press, 2005: 223-244 (in Chinese). 林建忠, 阮晓东, 陈邦国, 等. 流体力学[M]. 北京: 清华大学出版社, 2005: 223-244. |
