Perrot R, Mazodier J L.Hollow bodies produced by powder extrusion of aluminum-silicon alloys: US, 4155756 .1979-05-22.
[2]
Rückert F, Stocker P, Biedermann R, Rieger R. Cylinder liner of a hypereutectic aluminum/silicon alloy for use in a crankcase of a reciprocating piston engine and process for producing such a cylinder liner: US, 6096143 . 2000-08-01.
Ha T K, Park W J, Ahn S, Chang Y W. Fabrication of spray-formed hypereutectic Al-25Si alloy and its deformation behavior [J]. Journal of Materials Processing Technology, 2002, 130-131: 691-695.
[5]
Uozatoa Susumu, Nakatab Kazuhiro, Ushiob Masao. Evaluation of ferrous powder thermal spray coatings on diesel engine cylinder bores [J]. Surface and Coatings Technology, 2005, 200(7): 2580-2586.
[6]
Bobzina K, Ernsta F, Richardta K, Schlaefera T, Verpoortb C, Floresc G. Thermal spraying of cylinder bores with the plasma transferred wire arc process [J]. Surface and Coatings Technology, 2008, 202(18): 4438-4443.
[7]
Fukui Y.Fundamental investigation of functionally gradient material manufacturing system using centrifugal force [J]. JSME International Journal Series Ⅲ : Vibration, Control Engineering, Engineering for Industry, 1991, 34(1): 144-148.
[8]
王渠东, 丁文江, 金俊泽. 离心铸造过共晶Al-Si合金自生表面复合材料 [J]. 复合材料学报, 1998, 15(3): 7-11. Wang Qudong, Ding Wenjiang, Jin Junze. In situ surface composites fabricated by centrifugally casting hypereutectic Al-Si alloy [J]. Acta Materiae Compositae Sinica, 1998, 15(3): 7-11.
[9]
Zhang Jian, Wang Yuqing, Zhou Benlian, Wu Xingqiang. Functionally graded Al/Mg2Si in-situ composites, prepared by centrifugal casting [J]. Journal of Materials Science Letters, 1998, 17(19): 1677-1679.
[10]
Zhang Jian, Fan Zhongyun, Wang Yuqing, Zhou Benlian. Hypereutectic aluminium alloy tubes with graded distribution of Mg2Si particles prepared by centrifugal casting [J]. Materials & Design, 2000, 21(3): 149-153.
[11]
谭银元. 离心铸造Al-16wt%Si合金自生梯度复合材料 [J]. 复合材料学报, 2002, 19(5): 47-51. Tan Yinyuan. In situ gradient compsites of Al-16wt%Si alloy by centrifugal casting [J]. Acta Materiae Compositae Sinica, 2002, 19(5): 47-51.
[12]
谭银元. 离心铸造过共晶Al-Si合金自生梯度复合材料及其阻尼性能 [J]. 中国有色金属学报, 2002, 12(2): 353-357. Tan Yinyuan. In situ gradient composite of hypertutectic Al-Si alloy by centrifugal casting and its damping property [J]. The Chinese Journal of Nonferrous Metals, 2002, 12(2): 353-357.
[13]
于思荣, 张新平, 何镇明, 刘耀辉. 初始Si含量对离心法制备过共晶Al-Si合金FGM中初晶硅分布的影响 [J]. 复合材料学报, 2003, 20(6): 16-20. Yu Sirong, Zhang Xinping, He Zhenming, Liu Yaohui. Influence of primary Si content on primary crystal silicon distribution in hypereutectic Al-Si alloy FGM prepared by centrifugal casting [J]. Acta Materiae Compositae Sinica, 2003, 20(6): 16-20.
[14]
Zhai Y B, Liu C M, Wang K, Zou M H, Xie Y. Characteristics of two Al based functionally gradient composites reinforced by primary Si particles and Si/in situ Mg2Si particles in centrifugal casting [J]. Transactions of Nonferrous Metals Society of China, 2010, 20(3): 361-70.
[15]
刘 雁. 离心铸造法制备Mg2Si(Si)/Al梯度复合材料及其耐磨性的研究 . 长春: 吉林大学, 2009. Liu Yan. Producing Mg2Si(Si)/Al gradient composites by centrifugal casting and study on wear ability . Changchun: Jilin University, 2009.
[16]
Zhang J, Fan Z, Wang Y Q, Zhou B L. Effect of cooling rate on the microstructure of hypereutectic Al-Mg2Si alloys [J]. Journal of Materials Science Letters, 2000, 19(20): 1825-1828.
[17]
Li Shunpu, Zhao Shengxu, Pan Mingxiang, Zhao Deqian, Chen Xichen, Barabash O M, Barabash R I. Solidification and structural characteristics of α(Al)-Mg2Si eutectic [J]. Materials Transactions, JIM, 1997, 38(6): 553-559.
[18]
Ogawa T, Watanabe Y, Sato H, Kim I S, Fukui Y. Theoretical study on fabrication of functionally graded material with density gradient by a centrifugal solid-particle method [J]. Composites Part A, 2006, 37(12): 2194-2200.
