In this study, bio-waste gas is converted to sustainable hydrogen energy in good quality and low pollution. In addition, generated highly concentrated hydrogen is applied to fuel cell (PEMFC) to resolve environmental and energy crisis issue via gliding arc plasma system. Parameters that can affect the reforming performance of bio-gas in gliding arc plasma system were studied. Especially, the optimal operating condition in water gas shift reactor and preferential oxidation reactor for CO removal was proposed. For the parametric re-searches, change in steam feed amount and temperature change in catalyst bed in water gas shift reactor were studied. For the preferential oxidation reactor, air input flow rate change and temperature variation in catalyst bed were evaluated. The optimal operating conditions for gliding arc plasma reforming system are proposed as 6:4 of biogas component ratio (i.e., CHR4R:CO), 3 of steam/carbon ratio, 16 L/min of total gas flow rate, and 2.4 kW of input electric power. Where, the concentration of biogas that passed each reactor shows 57.5% of HR2R, 7 ppm of CO, 9.2% of COR2R, and 3.4% of CHR4R. Therefore, less than 10 ppm of CO is achieved, and this system can be applicable for PEMFC.
References
[1]
P. Kolbitsch, C. Pfeifer and H. Hofbauer, “Catalytic Steam Reforming of Model Biogas,” Fuel, Vol. 87, No. 6, 2008, pp. 701-706. doi:10.1016/j.fuel.2007.06.002
[2]
S. T. Lin, Y. H. Chen, C. C. Yu, Y. C. Liu and C. H. Lee, “Modelling an Experimental Methane Fuel Processor,” Journal of Power Sources, Vol. 148, 2005, pp. 43-53.
doi:10.1016/j.jpowsour.2005.01.035
[3]
A. Jhalani and L. D. Schmidt, “Preferential CO Oxidation in the Presence of H2, H2O, and CO2 at Short Contact-Time,” Catalysis Letters, Vol. 104, No. 3-4, 2005, pp. 103-109. doi:10.1007/s10562-005-7937-9
[4]
Y. N. Chun and H. O. Song, “Syngas Production Using Gliding Arc Plasma,” Energy Sources, Vol. 30, No. 13, 2008, pp. 1202-1212. doi:10.1080/15567030600817670
[5]
T. Sreethawong, P. Thakonpatthanakun and S. Chavadej, “Partial Oxidation of Methane with Air for Synthesis Gas Production in a Multistage Gliding Arc Discharge System,” International Journal of Hydrogen Energy, Vol. 32, No. 8, 2007, pp. 1067-1079.
doi:10.1016/j.ijhydene.2006.07.013
[6]
A. Effendi, K. Hellgard, Z. G. Zhang and T. Yoshida, “Optimising H2 Production from Model Biogas via combined Steam Reforming and CO Shift Reactions,” Fuel, No. 84, No. 7-8, 2005, pp. 869-874.
doi:10.1016/j.fuel.2004.12.011
[7]
Y. N. Chun and S. C. Kim, “Production of Hydrogen-Rich Gas from Methane by Thermal Plasma Reform,” Journal of the Air & Waste management Association, Vol. 57, No. 12, 2007, pp. 1447-1451.
doi:10.3155/1047-3289.57.12.1447
[8]
J. D. Holladay, J. Hu, D. L. king and Y. Wang, “An Overview of Hydrogen Production Technologies,” Catalysis Today, Vol. 139, No. 4, 2009, pp. 244-260.
doi:10.1016/j.cattod.2008.08.039
[9]
S. Srinivas, A. Dhingra, H. Im and E. Gulari, “A Scalable Silicon Microreactor for Preferential CO Oxidation Performance Comparison with a Tubular Packed-Bed Microreactor,” Applied Catalysis A: General, Vol. 274, No. 1-2, 2004, pp. 285-293. doi:10.1016/j.apcata.2004.07.012
[10]
Z. G. Zhang, G. Xu, X. Chen, K. Honda and T. Yoshida, “Process Development of Hydrogenous Gas Production for PEFC from Biogas,” Fuel Processing Technology, Vol. 85, No. 8-10, 2004, pp. 1213-1229.
doi:10.1016/j.fuproc.2003.10.017
