The current study assesses the drying shrinkage behaviour of polyvinyl alcohol fibre reinforced concrete (PVA-FRC) containing short-length (6？mm) and long-length (12？mm) uncoated monofilament PVA fibres at 0.125%, 0.25%, 0.375%, and 0.5% volumetric fractions. Fly ash is also used as a partial replacement of Portland cement in all mixes. PVA-FRC mixes have been compared to length change of control concrete (devoid of fibres) at 3 storage intervals: early-age (0–7 days), short-term (0–28 days), and long-term (28–112 days) intervals. The shrinkage results of FRC and control concrete up to 112 days indicated that all PVA-FRC mixes exhibited higher drying shrinkage than control. The shrinkage exhibited by PVA-FRC mixes ranged from 449 to 480 microstrain, where this value was only 427 microstrain in the case of control. In addition, the longer fibres exhibited higher mass loss, thus potentially contributing to higher shrinkage. 1. Introduction Concrete is recognised as the most prevalent used construction material in the world [1]. It is reputable that concrete provides notable mechanical performance, great versatility, and economic efficiency in comparison to other construction materials [2]. However, it must be noted that concrete is discredited for its brittleness and strength-to-weight ratio. Moreover, in service, structural concrete undergoes volume change due to moisture loss by hydration and evaporation. This volume change and movement experienced in this manner is termed shrinkage [2]. Shrinkage of concrete commonly occurs as a decrease in volume via four primary mechanisms: capillary tension, surface tension, disjoining pressure, and change in water within the matrix of cement [3]. Concrete tends to reach equilibrium with its service environment. If the environment is a dry atmosphere the exposed surface of the concrete loses water by evaporation. The rate of evaporation will depend on the relative humidity, temperature, water-cement ratio, and the area of the exposed surface of the concrete [4, 5]. The first water to be lost from concrete is that held in the large capillary pores of the hardened concrete. The loss of this water does not cause significant volume change [6]. However, as explained by Tam et al. [7], as water continues to evaporate from the capillary and gel pores, a meniscus is formed along the network of capillary pores and surface tension is created. With the reduction in the vapour pressure in the capillary pores, tensile stress in the residual water increases. These tensile stresses are in equilibrium with compressive stresses
References
[1]
A. M. Alhozaimy and M. J. Shannag, “Performance of concretes reinforced with recycled plastic fibres,” Magazine of Concrete Research, vol. 61, no. 4, pp. 293–298, 2009.
[2]
J. J. Park, D. Yoo, S. Kim, and Y. Yoon, “Drying shrinkage cracking characteristics of ultra-high-performance fibre reinforced concrete with expansive and shrinkage reducing agents,” Magazine of Concrete Research, vol. 65, pp. 248–256, 2013.
[3]
K. Sakata, “A study on moisture diffusion in drying and drying shrinkage of concrete,” Cement and Concrete Research, vol. 13, no. 2, pp. 216–224, 1983.
[4]
B. I. G. Barr and A. S. A. El-Baden, “Shrinkage properties of normal and high strength fibre reinforced concrete,” Proceedings of the Institution of Civil Engineers: Structures and Buildings, vol. 156, no. 1, pp. 15–25, 2003.
[5]
Cement Concrete & Aggregates Australia, Drying Shrinkage of Cement and Concrete, C.C.A.A., 2002.
[6]
A. Neville, Properties of Concrete, 4th and Final Edition, John Wiley & Sons, 1991.
[7]
C. M. Tam, V. W. Y. Tam, and K. M. Ng, “Assessing drying shrinkage and water permeability of reactive powder concrete produced in Hong Kong,” Construction and Building Materials, vol. 26, no. 1, pp. 79–89, 2012.
[8]
G. W. Wash, “Volume changes of hardened concrete. Significance of tests and properties of concrete and concrete-making materials,” ASTM (STP 169-A), American Society for Testing and Materials, Philadelphia, Pa, USA, 1996.
[9]
M. Grzybowski and S. P. Shah, “Shrinkage cracking of fiber reinforced concrete,” ACI Materials Journal, vol. 87, no. 2, pp. 138–148, 1990.
[10]
S. W. Kim, J. J. Park, S. T. Kang, G. S. Ryo, and K. T. Koh, “Development of ultra high performance cementitious composites (UHPCC) in Korea,” in Proceedings of the 4th International Conference on Bridge Maintenance (IABMAS '08), p. 110, Seoul, Republic of Korea, July 2008.
[11]
B. A. Graybeal, “Flexural behavior of an ultrahigh-performance concrete I-girder,” Journal of Bridge Engineering, vol. 13, no. 6, pp. 602–610, 2008.
[12]
A. Kamen, E. Denarié, H. Sadouki, and E. Brühwiler, “Thermo-mechanical response of UHPFRC at early age—experimental study and numerical simulation,” Cement and Concrete Research, vol. 38, no. 6, pp. 822–831, 2008.
[13]
B. Chen and C. Fang, “Contribution of fibres to the properties of EPS lightweight concrete,” Magazine of Concrete Research, vol. 61, no. 9, pp. 671–678, 2009.
[14]
A. Noushini, B. Samali, and K. Vessalas, “Effect of polyvinyl alcohol (PVA) fibre on dynamic and material properties of fibre reinforced concrete,” Construction and Building Materials, vol. 49, pp. 374–383, 2013.
[15]
H. Kong, S. G. Bike, and V. C. Li, “Constitutive rheological control to develop a self-consolidating engineered cementitious composite reinforced with hydrophilic poly(vinyl alcohol) fibers,” Cement and Concrete Composites, vol. 25, no. 3, pp. 333–341, 2003.
[16]
V. C. Li and S. Wang, “Microstructure variability and macroscopic composite properties of high performance fiber reinforced cementitious composites,” Probabilistic Engineering Mechanics, vol. 21, no. 3, pp. 201–206, 2006.
[17]
D. Feldman, Polymeric Building Materials, Elsevier Applied Science, London, UK, 1989.
[18]
B. Xu, H. A. Toutanji, and J. Gilbert, “Impact resistance of poly(vinyl alcohol) fiber reinforced high-performance organic aggregate cementitious material,” Cement and Concrete Research, vol. 40, no. 2, pp. 347–351, 2010.
[19]
R. F. Zollo, “Fiber-reinforced concrete: an overview after 30 years of development,” Cement and Concrete Composites, vol. 19, no. 2, pp. 107–122, 1997.
[20]
S. B. Daneti, T. Wee, and T. Thangayah, “Effect of polypropylene fibres on the shrinkage cracking behaviour of lightweight concrete,” Magazine of Concrete Research, vol. 63, no. 11, pp. 871–881, 2011.
[21]
B. Arisoy, Development and Fracture Evaluation of High Performance Fiber Reinforced Lightweight Concrete, Wayne State University, 2002.
[22]
S. B. Daneti and T. Wee, “Behaviour of hybrid fibre reinforced high-strength lightweight aggregate concrete,” Magazine of Concrete Research, vol. 63, no. 11, pp. 785–796, 2011.
[23]
ACI-Comittee 544, “State-of-the-art report on fiber reinforced concrete,” Tech. Rep. A. 544. 1R-96, American Concrete Institute, 2002.
[24]
D. Nicolaides, A. Kanellopoulos, and B. L. Karihaloo, “Fatigue life and self-induced volumetric changes of CARDIFRC,” Magazine of Concrete Research, vol. 62, no. 9, pp. 679–683, 2010.
[25]
J. Zhang, H. Stang, and V. C. Li, “Crack bridging model for fibre reinforced concrete under fatigue tension,” International Journal of Fatigue, vol. 23, no. 8, pp. 655–670, 2001.
[26]
R. Combrinck and W. P. Boshoff, “Typical plastic shrinkage cracking behaviour of concrete,” Magazine of Concrete Research, vol. 65, pp. 486–493, 2013.
[27]
H. Wu and V. C. Li, “Trade-off between strength and ductility of random discontinuous fiber reinforced cementitious composites,” Cement and Concrete Composites, vol. 16, no. 1, pp. 23–29, 1994.
[28]
BSI, BS, 8110 Part 2, Structural Use of Concrete. Code of Practice for Design and Construction, BSI, London, UK, 1985.
[29]
A. Izaguirre, J. Lanas, and J. I. Alvarez, “Effect of a polypropylene fibre on the behaviour of aerial lime-based mortars,” Construction and Building Materials, vol. 25, no. 2, pp. 992–1000, 2011.
[30]
N. Ghosni, K. Vessalas, and B. Samali, “Evaluation of fresh properties effect on the compressive strength of polypropylene fibre reinforced polymer modified concrete,” in Proceedings of the 22nd Australasian Conference on the Mechanics of Structures and Materials (ACMSM '12), Sydney, Australia, 2012.
[31]
D. V. Soulioti, N. M. Barkoula, A. Paipetis, and T. E. Matikas, “Effects of fibre geometry and volume fraction on the flexural behaviour of steel-fibre reinforced concrete,” Strain, vol. 47, no. 1, pp. e535–e541, 2011.
[32]
M. A. O. Mydin and S. Soleimanzadeh, “Effect of polypropylene fiber content on flexural strength of lightweight foamed concrete at ambient and elevated temperatures,” Advances in Applied Science Research, vol. 3, no. 5, pp. 2837–2846, 2012.
[33]
D. J. Hannant, “Fibre-reinforced concrete,” in Advanced Concrete Technology Set, J. Newman and B. S. Choo, Eds., pp. 6/1–6/17, Butterworth-Heinemann, Oxford, UK, 2003.
[34]
V. Corinaldesi and G. Moriconi, “Characterization of self-compacting concretes prepared with different fibers and mineral additions,” Cement and Concrete Composites, vol. 33, no. 5, pp. 596–601, 2011.
[35]
A. Bentur and A. Goldman, “Curing effects, strength and physical properties of high strength silica fume concretes,” Journal of Materials in Civil Engineering, vol. 1, no. 1, pp. 46–58, 1989.
[36]
E. El Hindy, B. Miao, O. Chaallal, and P. Aitcin, “Drying shrinkage of ready-mixed high-performance concrete,” ACI Materials Journal, vol. 91, no. 3, pp. 300–305, 1994.
[37]
S. Ghosh and K. W. Nasser, “Creep, shrinkage, frost, and sulphate resistance of high strength concrete,” Canadian Journal of Civil Engineering, vol. 22, no. 3, pp. 621–636, 1995.
[38]
A. Bentur and S. Mindess, Fiber Reinforced Cementitious Composites, Elsevier Applied Science, 1990.
[39]
P. N. Balaguru and S. P. Shah, Fiber Reinforced Cement Composites, McGraw Hill, 1992.
[40]
B. Feleko？lu, K. Tosun, and B. Baradan, “Effects of fibre type and matrix structure on the mechanical performance of self-compacting micro-concrete composites,” Cement and Concrete Research, vol. 39, no. 11, pp. 1023–1032, 2009.
[41]
C. Redon, V. C. Li, C. Wu, H. Hoshiro, T. Saito, and A. Ogawa, “Measuring and modifying interface properties of PVA fibers in ECC matrix,” Journal of Materials in Civil Engineering, vol. 13, no. 6, pp. 399–406, 2001.
[42]
V. C. Li, C. Wu, S. Wang, A. Ogawa, and T. Saito, “Interface tailoring for strain-hardening polyvinyl alcohol-engineered cementitious composite (PVA-ECC),” ACI Materials Journal, vol. 99, no. 5, pp. 463–472, 2002.
[43]
V. C. Li, T. Kanda, and Z. Lin, “The influence of fibre/matrix interface properties on complementary energy and composite damage tolerance,” in Proceedings of the 3rd Conference on Fracture and Strength of Solids, Hong Kong, 1997.
