Active magnetic bearings (AMBs) have become a key technology in various industrial applications. Self-sensing AMBs provide an integrated sensorless solution for position estimation, consolidating the sensing and actuating functions into a single electromagnetic transducer. The approach aims to reduce possible hardware failure points, production costs, and system complexity. Despite these advantages, self-sensing methods must address various technical challenges to maximize the performance thereof. This paper presents the direct current measurement (DCM) approach for self-sensing AMBs, denoting the direct measurement of the current ripple component. In AMB systems, switching power amplifiers (PAs) modulate the rotor position information onto the current waveform. Demodulation self-sensing techniques then use bandpass and lowpass filters to estimate the rotor position from the voltage and current signals. However, the additional phase-shift introduced by these filters results in lower stability margins. The DCM approach utilizes a novel PA switching method that directly measures the current ripple to obtain duty-cycle invariant position estimates. Demodulation filters are largely excluded to minimize additional phase-shift in the position estimates. Basic functionality and performance of the proposed self-sensing approach are demonstrated via a transient simulation model as well as a high current (10 A) experimental system. A digital implementation of amplitude modulation self-sensing serves as a comparative estimator.
References
[1]
Maslen, E.H. Self-Sensing Magnetic Bearings. In Magnetic Bearings: Theory, Design, and Application to Rotating Machinery; Springer-Verlag: Berlin, Germany, 2009; pp. 435–460.
[2]
Noh, M.D. Self-Sensing Magnetic Bearings Driven by a Switching Power Amplifier. Ph.D. Thesis, University of Virginia, Charlottesville, VA, USA, January 1996.
[3]
Schammass, A.; Herzog, R.; Bühler, P.; Bleuler, H. New results for self-sensing active magnetic bearings using modulation approach. IEEE Trans. Control Syst. Technol. 2005, 13, 509–516.
[4]
Maslen, E.H. Self-Sensing for Active Magnetic Bearings: Overview and Status. Proceedings of the Tenth International Symposium on Magnetic Bearings, Martigny, Switzerland, 21–23 August 2006; pp. 13–19.
[5]
Vischer, D.; Bleuler, H. Self-sensing Active Magnetic Levitation. IEEE Trans. Magn. 1993, 29, 1276–1281.
[6]
Morse, N.; Smith, R.; Paden, B.; Antaki, J. Position Sensed and Self-Sensing Magnetic Bearing Configurations and Associated Robustness Limitations. Proceedings of the 37th IEEE Conference on Decision and Control, Tampa, FL, USA, 16–18 December 1998; pp. 2599–2604.
[7]
Maslen, E.H.; Montie, D.T.; Iwasaki, T. Robustness limitations in self-sensing magnetic bearings. ASME J. Dyn. Syst. Meas. Control 2006, 128, 197–203.
[8]
Montie, D.T. Performance Limitations and Self-Sensing Magnetic Bearings. Ph.D. Thesis, University of Virginia, Charlottesville, VA, USA, January 2003.
[9]
Yim, J.-S.; Kim, J.-H.; Sul, S.-K.; Ahn, H.-J.; Han, D.-C. Sensorless Position Control of Active Magnetic Bearings Based on High Frequency Signal Injection Method. Proceedings of Eighteenth Annual IEEE Applied Power Electronics Conference and Exposition, (APEC'03), Miami Beach, FL, USA, 9–13 February 2003; pp. 83–88.
[10]
Ranft, E.O.; van Schoor, G.; du Rand, C.P. Self-sensing for electromagnetic actuators. Part I: A coupled reluctance network model approach. Sens. Actuators A 2011, 172, 400–409.
[11]
Ranft, E.O.; van Schoor, G.; du Rand, C.P. Self-sensing for electromagnetic actuators. Part II: Position estimation. Sens. Actuators A 2011, 172, 410–419.
[12]
Montie, D.T.; Maslen, E.H. Experimental Self-sensing Results for a Magnetic Bearing. Proceedings of the Seventh International Symposium on Magnetic Bearings, Zurich, Switzerland, 23–25 August 2000; pp. 171–176.
[13]
Niemann, A. Self-Sensing Algorithms for Active Magnetic Bearings. Ph.D. Thesis, North-West University, Potchefstroom, South Africa, November 2008.
[14]
Hu, B.; Micheal, A. Robustness analysis of digital feedback control systems with time-varying sample periods. J. Frankl. Inst. 2000, 337, 117–130.
[15]
Skrika, N.; Markert, R. Influence of Cross-Axis Sensitivity and Coordinate Coupling on Self-Sensing. Proceedings of the Sixth International Symposium on Magnetic Suspension Technology, Turin, Italy, 7–11 October 2001; pp. 179–184.
[16]
Ranft, E.O. An Improved Model for Self-Sensing Heteropolar Active Magnetic Bearings. Ph.D. Thesis, North West University, Potchefstroom, South Africa, December 2007.
[17]
Noh, M.D.; Montie, D.T.; Maslen, E.H. A Simulation Model for the Analysis of Transient Magnetic Bearing Performance. Proceedings of the Seventh International Symposium on Magnetic Bearings, Zurich, Switzerland, 23–25 August 2000; pp. 177–181.
[18]
International Standards Organization. Mechanical Vibration: Vibration of Rotating Machinery Equipped with Active Magnetic Bearings—Part 3: Evaluation of Stability Margin. ISO Standard 14839-3:2006, ISO TC108/SC2/WG7 AMB; Geneva, Switzerland, 2007.
[19]
Herzog, R.; Blanc, P. A Comparison of Linear Periodic and Nonlinear Control Strategies for Self-Sensing Magnetic Bearings. Proceedings of the Twelfth International Symposium on Magnetic Bearings, Wuhan, China, 22–25 August 2010; pp. 461–469.
