Banana fiber reinforced phenol formaldehyde composites with different fiber lengths and fiber loadings were prepared by compression molding (CM) and resin transfer molding (RTM) techniques. The mechanical properties such as tensile, flexural, and impact behavior were studied. RTM composites showed improved tensile and flexural properties as compared to CM composites. On the other hand, impact strength of RTM composites is slightly lower than that of CM composites. From the studies, it was found that mechanical properties increased with the increase in fiber loading, reached a plateau at 30–40？wt%, and then subsequently decreased with an increase in fiber loading in both techniques. At high fiber weight fractions, the strength decreased due to poor wetting and very poor stress transfer. The stress value increased up to 30？mm fiber lengths and then decreased. In order to examine the fracture surface morphology of the composites, scanning electron microscopy (SEM) was performed on the composite samples. A good relationship between morphological and mechanical properties has been observed. Finally, tensile strength of the composites fabricated by RTM and CM was compared with theoretical predictions. 1. Introduction In recent years, there has been a tremendous interest in the usage of plant fibers as reinforcement in polymer matrices for the manufacture of automobile components [1–6]. Lignocellulosic materials can significantly contribute to the development of biobased composites [7–9]. A few reports from the literature on green fiber polymer composites are summarized afterwords. Francucci et al. worked to understand how the main processing variables are affected when glass fibers are replaced by natural fibers in reinforced plastics [10]. Good flow properties and appreciable mechanical properties came to attention when Oksman manufactured high quality flax fiber reinforced composite using RTM [11]. Sreekumar et al. studied the mechanical and water absorption properties of sisal fiber reinforced polyester composites fabricated by RTM and CM techniques. They found that the composites made by RTM exhibited superior mechanical property and less water sorption due to good fiber/matrix interaction which was a result of low void content and good fiber wetting [12]. Peponi et al. extended a statistical approach to develop a comparative study on the mechanical properties of different natural fibers [13]. Kaith and Kalia studied grafting of flax fiber with vinyl monomers for enhancement of properties of flax-phenolic composites [14]. Megiatto et al. studied the
References
[1]
F. T. Wallenberger, “Value-in-use of composite reinforcing fibers,” MRS Proceedings, vol. 702, 2001.
[2]
D. Plackett, “The natural fiber-polymer composite industry in Europe technology and markets,” in Proceedings of the Progress on Woodfibre-Plastic Composites Conference, University of Toronto and Materials and Manufacturing Ontario, Toronto, Canada, 2002.
[3]
B. C. Suddell and W. J. Evans, “The increasing use and application of natural fibre composites materials within the automotive industry,” in Proceedings of the 7th International Conference on Woodfiber-Plastic Composites, Forest Products Society, Madison, Wis, USA, 2003.
[4]
J. Müssig, M. Karus, and R. R. Franck, “Bast and leaf fibre composite materials,” in Bast and Other Plant Fibres, R. R. Franck, Ed., vol. 345, chapter 10, Woodhead Publishing Limited, Cambridge, UK, 2005.
[5]
A. K. Bledzki, V. E. Sperber, and O. Faruk, “Natural and wood fiber reinforcement in polymers,” Rapra Review Reports, vol. 13, p. 152, 2002.
[6]
C. M. Clemons and D. F. Caulfield, “Functional fillers for plastics,” in Natural Fibers, M. Xanthos, Ed., vol. 249, chapter 11, Wiley-VCH, Weinheim, Germany, 2005.
[7]
K. G. Satyanarayana, K. Sukumaran, P. S. Mukherjee, C. Pavithran, and S. G. K. Pillai, “Natural fibre-polymer composites,” Cement and Concrete Composites, vol. 12, no. 2, pp. 117–136, 1990.
[8]
K. G. Satyanarayana, G. G. C. Arizaga, and F. Wypych, “Biodegradable composites based on lignocellulosic fibers: an overview,” Progress in Polymer Science, vol. 34, no. 9, pp. 982–1021, 2009.
[9]
M. J. John and S. Thomas, “Biofibres and biocomposites,” Carbohydrate Polymers, vol. 71, no. 3, pp. 343–364, 2008.
[10]
G. Francucci, E. S. Rodríguez, and A. Vázquez, “Study of saturated and unsaturated permeability in natural fiber fabrics,” Composites A, vol. 41, no. 1, pp. 16–21, 2010.
[11]
K. Oksman, “High quality flax fibre composites manufactured by the resin transfer moulding process,” Journal of Reinforced Plastics and Composites, vol. 20, no. 7, pp. 621–627, 2001.
[12]
P. A. Sreekumar, K. Joseph, G. Unnikrishnan, and S. Thomas, “A comparative study on mechanical properties of sisal-leaf fibre-reinforced polyester composites prepared by resin transfer and compression moulding techniques,” Composites Science and Technology, vol. 67, no. 3-4, pp. 453–461, 2007.
[13]
L. Peponi, J. Biagiotti, J. M. Kenny, and I. Mondragòn, “Statistical analysis of the mechanical properties of natural fibers and their composite materials. II. Composite materials,” Polymer Composites, vol. 29, no. 3, pp. 321–325, 2008.
[14]
B. S. Kaith and S. Kalia, “Grafting of flax fiber (Linum usitatissimum) with vinyl monomers for enhancement of properties of flax-phenolic composites,” Polymer Journal, vol. 39, no. 12, pp. 1319–1327, 2007.
[15]
J. D. Megiatto Jr., F. B. Oliveira, D. S. Rosa, C. Gardrat, A. Castellan, and E. Frollini, “Renewable resources as reinforcement of polymeric matrices: composites based on phenolic thermosets and chemically modified sisal fibers,” Macromolecular Bioscience, vol. 7, no. 9-10, pp. 1121–1131, 2007.
[16]
R. Hu and J. K. Lim, “Fabrication and mechanical properties of completely biodegradable hemp fiber reinforced polylactic acid composites,” Journal of Composite Materials, vol. 41, no. 13, pp. 1655–1669.
[17]
M. Abdelmouleh, S. Boufi, M. N. Belgacem, and A. Dufresne, “Short natural-fibre reinforced polyethylene and natural rubber composites: effect of silane coupling agents and fibres loading,” Composites Science and Technology, vol. 67, no. 7-8, pp. 1627–1639, 2007.
[18]
A. Alawar, A. M. Hamed, and K. Al-Kaabi, “Characterization of treated date palm tree fiber as composite reinforcement,” Composites B, vol. 40, no. 7, pp. 601–606, 2009.
[19]
S. Joseph, M. S. Sreekala, Z. Oommen, P. Koshy, and S. Thomas, “A comparison of the mechanical properties of phenol formaldehyde composites reinforced with banana fibres and glass fibres,” Composites Science and Technology, vol. 62, no. 14, pp. 1857–1868, 2002.
[20]
L. A. Pothan, S. Thomas, and N. R. Neelakantan, “Short banana fiber reinforced polyester composites: mechanical, failure and aging characteristics,” Journal of Reinforced Plastics and Composites, vol. 16, no. 8, pp. 744–765, 1997.
[21]
G. Kalaprasad, B. Francis, S. Thomas et al., “Effect of fibre length and chemical modifications on the tensile properties of intimately mixed short sisal/glass hybrid fibre reinforced low density polyethylene composites,” Polymer International, vol. 53, no. 11, pp. 1624–1638, 2004.
[22]
G. Kalaprasad, G. Mathew, C. Pavithran, and S. Thomas, “Melt rheological behavior of intimately mixed short sisal-glass hybrid fiber-reinforced low-density polyethylene composites. I. Untreated fibers,” Journal of Applied Polymer Science, vol. 89, no. 2, pp. 432–442, 2003.
[23]
M. S. Sreekala, M. G. Kumaran, S. Joseph, M. Jacob, and S. Thomas, “Oil palm fibre reinforced phenol formaldehyde composites: influence of fibre surface modifications on the mechanical performance,” Applied Composite Materials, vol. 7, no. 5-6, pp. 295–329, 2000.
[24]
M. Idicula, S. K. Malhotra, K. Joseph, and S. Thomas, “Effect of layering pattern on dynamic mechanical properties of randomly oriented short banana/sisal hybrid fiber-reinforced polyester composites,” Journal of Applied Polymer Science, vol. 97, no. 5, pp. 2168–2174, 2005.
[25]
R. David, S. Mohini, and M. Couturier, “Resin transfer molding of hemp fiber composites: optimization of the process and mechanical properties of the materials,” Composites Science and Technology, vol. 66, no. 7-8, pp. 895–906, 2006.
[26]
Y. Xue, Y. Du, S. Elder, K. Wang, and J. Zhang, “Temperature and loading rate effects on tensile properties of kenaf bast fiber bundles and composites,” Composites B, vol. 40, no. 3, pp. 189–196, 2009.
[27]
H. G. Elias, Macromolecules, vol. 2, Plenum Press, New York, NY, USA, 2nd edition, 1984.
[28]
M. K. Kang, W. I. Lee, and H. T. Hahn, “Formation of microvoids during resin-transfer molding process,” Composites Science and Technology, vol. 60, no. 12-13, pp. 2427–2434, 2000.
[29]
S. A. Paul, K. Joseph, G. D. G. Mathew, L. A. Pothen, and S. Thomas, “Influence of polarity parameters on the mechanical properties of composites from polypropylene fiber and short banana fiber,” Composites A, vol. 41, no. 10, pp. 1380–1387, 2010.
[30]
T. J. Hirsch, “Modulus of elasticity of concrete affected by elastic moduli of cement paste matrix and aggregate,” Journal of the American Concrete Institute, vol. 59, p. 427, 1962.
[31]
G. Kalaprasad, K. Joseph, S. Thomas, and C. Pavithran, “Theoretical modelling of tensile properties of short sisal fibre-reinforced low-density polyethylene composites,” Journal of Materials Science, vol. 32, no. 16, pp. 4261–4267, 1997.
