Activated carbon cloths have received growing attention because they offer comparative advantages over the traditional powdered or granular forms of this well-known adsorbent, providing further potential uses for technological innovations in several fields. The present article provides an overview of research studies and advances concerned with the development of activated carbon cloths and their use as adsorbent in environmental applications, mostly reported in the last years. The influence of some fabrics and textile wastes used as precursors, and of main activation process variables on the development and physicochemical, mechanical and/or electrical properties of the resulting activated carbon cloths are first reviewed. Then, investigations dealing with the removal of water and air pollutants by adsorption onto activated carbon cloths, including advances toward optimizing their regeneration after organic vapors saturation, are presented. 1. Introduction Activated carbon in powdered and granular forms is a well-known, versatile adsorbent of widespread use in a broad spectrum of applications, including purification, remediation of polluted aquatic environments, treatment of liquid and gaseous effluents generated in industry, gas storage and delivery, metal recovery, catalysis, and biomedical applications, among various others [1–12]. Growing concern and stricter regulations pertaining to environmental pollution have led to the increase of the activated carbon demand, which is forecasted to continue raising in the near future [13, 14]. In the last years, activated carbon cloths (ACCs) have gained increasing interest because they offer comparative advantages over the traditional forms and potentialities for technological innovation in different fields, including their potential use in cell therapy, as a support for stem cell growth [15]. Main advantages arise from the small diameter of the fibers constituting ACC [16]. They include faster adsorption kinetics, higher efficiency, and larger capacity for adsorption due to the higher surface area and pore volume of the ACC. In particular, micropores (<2?nm) of ACC are directly connected to the external surface area, thus diminishing heat and mass transfer resistances and lowering pressure drops in flow units [3, 17–20]. Besides, activated carbon cloths are light materials that can be arranged in different stable configurations and provide a contiguous carbon form suited for electrical and electrochemical applications [21–24]. Moreover, Joule effect heating of ACC offers additional benefits in terms of
References
[1]
R. C. Bansal and M. Goyal, Activated Carbon Adsorption, CRC Press, Boca Raton, Fla, USA, 2005.
[2]
M. C. Basso and A. L. Cukierman, “Arundo donax-based activated carbons for aqueous-phase adsorption of volatile organic compounds,” Industrial and Engineering Chemistry Research, vol. 44, no. 7, pp. 2091–2100, 2005.
[3]
H. Marsh and F. R. Reinoso, Activated Carbon, Elsevier, Oxford, UK, 2006.
[4]
T. J. Bandosz, Activated Carbon Surfaces in Environmental Remediation, Academic Press, 2006.
[5]
R. V. Ramanujan, S. Purushotham, and M. H. Chia, “Processing and characterization of activated carbon coated magnetic particles for biomedical applications,” Materials Science and Engineering C, vol. 27, no. 4, pp. 659–664, 2007.
[6]
P. Le Cloirec and C. Faur-Brasquet, “Adsorption of inorganic species from aqueous solutions,” in Adsorption By Carbons, E. J. Bottani and J. M. D. Tascón, Eds., Chapter 24, pp. 631–651, Elsevier, Oxford, UK, 2008.
[7]
J. de Celis, N. E. Amadeo, and A. L. Cukierman, “In situ modification of activated carbons developed from a native invasive wood on removal of trace toxic metals from wastewater,” Journal of Hazardous Materials, vol. 161, no. 1, pp. 217–223, 2009.
[8]
J. Rivera-Utrilla, M. Sanchez-Polo, V. Gomez-Serrano, P. M. Alvarez, M. C. M. Alvim-Ferraz, and J. M. Dias, “Activated carbon modifications to enhance its water treatment applications. An overview,” Journal of Hazardous Materials, vol. 187, pp. 1–23, 2011.
[9]
J. F. Kwiatkowski, Ed., Activated Carbon: Classifications, Properties and Applications, Nova Science Publishers, New York, NY, USA, 2012.
[10]
G. Mezohegyi, F. P. Van Der Zee, J. Font, A. Fortuny, and A. Fabregat, “Towards advanced aqueous dye removal processes: a short review on the versatile role of activated carbon,” Journal of Environmental Management, vol. 102, pp. 148–164, 2012.
[11]
J. Wang and S. Kaskel, “KOH activation of carbon-based materials for energy storage,” Journal of Materials Chemistry, vol. 22, pp. 23710–23725, 2012.
[12]
G. V. Nunell, M. E. Fernández, P. R. Bonelli, and A. L. Cukierman, “Removal of nitrate from wastewater by activated carbons developed from sawdust of an invasive wood,” Biomass and Bioenergy, vol. 44, pp. 87–95, 2012.
S. Román, J. M. V. Nabais, B. Ledesma, J. F. González, C. Laginhas, and M. M. Titirici, “Production of low-cost adsorbents with tunable surface chemistry by conjunction of hydrothermal carbonization and activation processes,” Microporous and Mesoporous Materials, vol. 165, pp. 127–133, 2013.
[15]
J. L. Pe?alver, J. L. Linares-Fernández, V. de Araujo Farías et al., “Activated carbon cloth as support for mesenchymal stem cell growth and differentiation to osteocytes,” Carbon, vol. 47, no. 15, pp. 3574–3577, 2009.
[16]
S. Y. Lee and S. J. Park, “Determination of the optimal pore size for improved CO2 adsorption in activated carbon fibers,” Journal of Colloid and Interface Science, vol. 389, pp. 230–235, 2013.
[17]
F. Rodríguez-Reinoso, “Production and applications of activated carbons,” in Handbook of Porous Solids, F. Schüth, K. S. W. Sing, and J. Weitkamp, Eds., Chapter 4, 8, 1, pp. 1766–1827, Wiley-VCH, Weinheim, Germany, 2002.
[18]
J. M. D. Tascón, “Overview of carbon materials in relation to adsorption,” in Adsorption By Carbons, E. J. Bottani and J. M. D. Tascón, Eds., pp. 15–49, Elsevier, Oxford, UK, 2008.
[19]
A. Linares-Solano and D. Cazorla-Amorós, “Adsorption on activated carbon fibers,” in Adsorption By Carbons, E. J. Bottani and J. M. D. Tascón, Eds., Chapter 17, pp. 431–449, Elsevier, Oxford, UK, 2008.
[20]
P. Le Cloirec, “Adsorption of activated carbon fiber cloth and electrothermal desorption of volatile organic compounds (VOCs): a specific review,” Chinese Journal of Chemical Engineering, vol. 20, no. 3, pp. 461–468, 2012.
[21]
C. O. Ania and F. Béguin, “Mechanism of adsorption and electrosorption of bentazone on activated carbon cloth in aqueous solutions,” Water Research, vol. 41, pp. 3372–3380, 2007.
[22]
C. O. Ania and F. Béguin, “Electrochemical regeneration of activated carbon cloth exhausted with bentazone,” Environmental Science & Technology, vol. 42, pp. 4500–4506, 2008.
[23]
G. Milczarek, A. Ciszewski, and I. Stepniak, “Oxygen-doped activated carbon fiber cloth as electrode material for electrochemical capacitor,” Journal of Power Sources, vol. 196, no. 18, pp. 7882–7885, 2011.
[24]
I. Villar, D. J. S. De la Calle, Z. González et al., “Carbon materials as electrodes for electrosorption of NaCl in aqueous solutions,” Adsorption, vol. 17, pp. 467–471, 2011.
[25]
A. Subrenat, J. N. Baléo, P. Le Cloirec, and P. E. Blanc, “Electrical behaviour of activated carbon cloth heated by the joule effect: desorption application,” Carbon, vol. 39, no. 5, pp. 707–716, 2001.
[26]
A. Subrenat and P. Le Cloirec, “Thermal behavior of activated carbon cloths heated by Joule effect,” Journal of Environmental Engineering, vol. 129, no. 12, pp. 1077–1084, 2003.
[27]
A. Badalyan, R. Bromball, P. Pendleton, and W. Skinner, “An assessment of activated carbon cloth microporosity change due to chemical activation,” Carbon, vol. 48, no. 4, pp. 1004–1011, 2010.
[28]
M. E. Ramos, P. R. Bonelli, and A. L. Cukierman, “Strategies for optimizing the development of cellulose-based activated carbon cloths by the chemical activation process,” in Activated Carbon: Classifications, Properties and Applications, J. F. Kwiatkowski, Ed., Chapter 15, pp. 475–507, Nova Science Publishers, New York, NY, USA, 2011.
[29]
D. L. Johnsen and M. J. Rood, “Temperature control during regeneration of activated carbon fiber cloth with resistance-feedback,” Environmental Science & Technology, vol. 46, pp. 11305–11312, 2012.
[30]
A. Subrenat, J. Bellettre, and P. Le Cloirec, “3-D numerical simulations of flows in a cylindrical pleated filter packed with activated carbon cloth,” Chemical Engineering Science, vol. 58, no. 22, pp. 4965–4973, 2003.
[31]
L. Kiwi-Minsker, M. Ruta, T. Eslanloo-Pereira, and B. Bromley, “Structured catalytic wall microreactor for efficient performance of exothermic reactions,” Chemical Engineering and Processing, vol. 49, no. 9, pp. 973–978, 2010.
[32]
D. Bremner and I. Johnson, “In vogue,” Chemical Engineer, vol. 836, pp. 40–41, 2011.
[33]
Y. Matatov-Meytal and M. Sheintuch, “Catalytic fibers and cloths,” Applied Catalysis A, vol. 231, no. 1-2, pp. 1–16, 2002.
[34]
U. I. Matatov-Meytal, “Radial-flow reactor packed with a catalytic cloth: nitrate reduction in hydrogen-saturated water,” Industrial and Engineering Chemistry Research, vol. 44, no. 25, pp. 9575–9580, 2005.
[35]
U. Matatov-Meytal and M. Sheintuch, “Activated carbon cloth-supported Pd-Cu catalyst: application for continuous water denitrification,” Catalysis Today, vol. 102-103, pp. 121–127, 2005.
[36]
V. Gaur, A. Sharma, and N. Verma, “Catalytic oxidation of toluene and m-xylene by activated carbon fiber impregnated with transition metals,” Carbon, vol. 43, no. 15, pp. 3041–3053, 2005.
[37]
P. Korovchenko, A. Renken, and L. Kiwi-Minsker, “Microwave plasma assisted preparation of Pd-nanoparticles with controlled dispersion on woven activated carbon fibres,” Catalysis Today, vol. 102-103, pp. 133–141, 2005.
[38]
A. Perrard, P. Gallezot, J. P. Joly et al., “Highly efficient metal catalysts supported on activated carbon cloths: a catalytic application for the hydrogenation of d-glucose to d-sorbitol,” Applied Catalysis A, vol. 331, no. 1, pp. 100–104, 2007.
[39]
R. B. Biniwale and M. Ichikawa, “Thermal imaging of catalyst surface during catalytic dehydrogenation of cyclohexane under spray-pulsed conditions,” Chemical Engineering Science, vol. 62, no. 24, pp. 7370–7377, 2007.
[40]
P. D. Tien, T. Satoh, M. Miura, and M. Nomura, “Continuous hydrogen evolution from cyclohexanes over platinum catalysts supported on activated carbon fibers,” Fuel Processing Technology, vol. 89, no. 4, pp. 415–418, 2008.
[41]
D. Xu, Z. H. Huang, F. Kang, M. Inagaki, and T. H. Ko, “Effect of heat treatment on adsorption performance and photocatalytic activity of TiO2-mounted activated carbon cloths,” Catalysis Today, vol. 139, no. 1-2, pp. 64–68, 2008.
[42]
J. C. Naranjo, A. Córdoba, L. Giraldo, V. S. García, and J. C. Moreno-Piraján, “Lipase supported on granular activated carbon and activated carbon cloth as a catalyst in the synthesis of biodiesel fuel,” Journal of Molecular Catalysis B, vol. 66, pp. 166–171, 2010.
[43]
M. A. Fontecha-Cámara, M. A. álvarez-Merino, F. Carrasco-Marín, M. V. López-Ramón, and C. Moreno-Castilla, “Heterogeneous and homogeneous Fenton processes using activated carbon for the removal of the herbicide amitrole from water,” Applied Catalysis B, vol. 101, pp. 425–430, 2011.
[44]
J. V. Pande, A. Shukla, and R. B. Biniwale, “Catalytic dehydrogenation of cyclohexane over Ag-M/ACC catalysts for hydrogen supply,” International Journal of Hydrogen Energy, vol. 37, no. 8, pp. 6756–6763, 2012.
[45]
I. Isaev, G. Salitra, A. Soffer, Y. S. Cohen, D. Aurbach, and J. Fischer, “A new approach for the preparation of anodes for Li-ion batteries based on activated hard carbon cloth with pore design,” Journal of Power Sources, vol. 119–121, pp. 28–33, 2003.
[46]
K. Babel and K. Jurewicz, “KOH activated carbon fabrics as supercapacitor material,” Journal of Physics and Chemistry of Solids, vol. 65, no. 2-3, pp. 275–280, 2004.
[47]
C. Sivakumar, J. N. Nian, and H. Teng, “Poly(o-toluidine) for carbon fabric electrode modification to enhance the electrochemical capacitance and conductivity,” Journal of Power Sources, vol. 144, no. 1, pp. 295–301, 2005.
[48]
C. M. Chuang, C. W. Huang, H. Teng, and J. M. Ting, “Effects of carbon nanotube grafting on the performance of electric double layer capacitors,” Energy and Fuels, vol. 24, no. 12, pp. 6476–6482, 2010.
[49]
A. Lewandowski, A. Olejniczak, M. Galinski, and I. Stepniak, “Performance of carbon-carbon supercapacitors based on organic, aqueous and ionic liquid electrolytes,” Journal of Power Sources, vol. 195, no. 17, pp. 5814–5819, 2010.
[50]
Y. Geng, Y. Song, M. Zhong, J. Shi, Q. Guo, and L. Liu, “Influence of the pitch fluoride on the electrical conductivity of the activated carbon cloth as electrodes of the supercapacitor,” Materials Letters, vol. 64, no. 24, pp. 2673–2675, 2010.
[51]
R. Elazari, G. Salitra, A. Garsuch, A. Panchenko, and D. Aurbach, “Sulfur-impregnated activated carbon fiber cloth as a binder-free cathode for rechargeable Li-S batteries,” Advanced Materials, vol. 23, no. 47, pp. 5641–5644, 2011.
[52]
I. Stepniak and A. Ciszewski, “Electrochemical characteristics of a new electric double layer capacitor with acidic polymer hydrogel electrolyte,” Electrochimica Acta, vol. 56, no. 5, pp. 2477–2482, 2011.
[53]
N. Zhu, X. Chen, T. Zhang, P. Wu, P. Li, and J. Wu, “Improved performance of membrane free single-chamber air-cathode microbial fuel cells with nitric acid and ethylenediamine surface modified activated carbon fiber felt anodes,” Bioresource Technology, vol. 102, no. 1, pp. 422–426, 2011.
[54]
M. T. Z. Myint and J. Dutta, “Fabrication of zinc oxide nanorods modified activated carbon cloth electrode for desalination of brackish water using capacitive deionization approach,” Desalination, vol. 305, pp. 24–30, 2012.
[55]
H. Xia, “Study on the treatment of high concentration dye wastewater on modified active carbon cloth electrode,” Advanced Materials Research, vol. 347–353, pp. 1869–1873, 2012.
[56]
M. Zhong, Y. Song, Y. Li et al., “Effect of reduced graphene oxide on the properties of an activated carbon cloth/polyaniline flexible electrode for supercapacitor application,” Journal of Power Sources, vol. 217, pp. 6–12, 2012.
[57]
B. V. Kaludjerovi?, M. S. Trtica, B. B. Radak, J. M. St?si?, S. S. K. M?sovi?, and V. M. Dodevski, “Analysis of the interaction of pulsed laser with nanoporous activated carbon cloth,” Journal of Materials Science & Technology, vol. 27, no. 11, pp. 979–984, 2011.
[58]
J. H. Tsai, H. M. Chiang, G. Y. Huang, and H. L. Chiang, “Adsorption characteristics of acetone, chloroform and acetonitrile on sludge-derived adsorbent, commercial granular activated carbon and activated carbon fibers,” Journal of Hazardous Materials, vol. 154, no. 1–3, pp. 1183–1191, 2008.
[59]
T. J. Bandosz, “Removal of inorganic gases and VOCs on activated carbons,” in Adsorption By Carbons, E. J. Bottani and J. M. D. Tascón, Eds., Chapter 21, pp. 533–556, Elsevier, Oxford, UK, 2008.
[60]
M. Yao, Q. Zhang, D. W. Hand, D. L. Perram, and R. Taylor, “Investigation of the treatability of the primary indoor volatile organic compounds on activated carbon fiber cloths at typical indoor concentrations,” Journal of the Air and Waste Management Association, vol. 59, no. 7, pp. 882–890, 2009.
[61]
R. Chand, R. Molina, I. Johnson, A. Hans, and D. H. Bremner, “Activated carbon cloth: a potential adsorbing/oxidizing catalyst for phenolic wastewater,” Water Science and Technology, vol. 61, no. 11, pp. 2817–2823, 2010.
[62]
C. C. Huang and Y. J. Su, “Removal of copper ions from wastewater by adsorption/electrosorption on modified activated carbon cloths,” Journal of Hazardous Materials, vol. 175, no. 1–3, pp. 477–483, 2010.
[63]
C. Moreno-Castilla, M. A. álvarez-Merino, L. M. Pastrana-Martínez, and M. V. López-Ramón, “Adsorption mechanisms of metal cations from water on an oxidized carbon surface,” Journal of Colloid and Interface Science, vol. 345, pp. 461–466, 2010.
[64]
S. Azizian, Z. Niknam, and E. Rombi, “Adsorption of pentafluorophenol onto powdered, granular, and cloth activated carbons,” Journal of Dispersion Science and Technology, vol. 33, no. 2, pp. 206–212, 2012.
[65]
A. Hajian and S. Azizian, “On the adsorption of some catechol derivatives from aqueous solutions onto activated carbon cloth: equilibrium and kinetic studies,” Journal of Dispersion Science and Technology, vol. 33, no. 11, pp. 629–1634, 2012.
[66]
W. Shen, H. Wang, R. Guan, and Z. Li, “Surface modification of activated carbon fiber and its adsorption for vitamin B1 and folic acid,” Colloids and Surfaces A, vol. 331, no. 3, pp. 263–267, 2008.
[67]
P. J. M. Carrott, J. M. V. Nabais, M. M. L. R. Carrott, and J. A. Menéndez, “Microwave heating as a novel method for introducing molecular sieve properties into activated carbon fibres,” Carbon, vol. 42, no. 1, pp. 227–229, 2004.
[68]
X. Shao, W. Wang, and X. Zhang, “Experimental measurements and computer simulation of methane adsorption on previous activated carbon fibers,” Carbon, vol. 45, no. 1, pp. 188–195, 2007.
[69]
J. Zhang, W. Luan, H. Huang, Y. Qi, and S. T. Tu, “Preparation and characteristics of Pt/ACC catalyst for thermoelectric thin film hydrogen sensor,” Sensors and Actuators B, vol. 128, no. 1, pp. 266–272, 2007.
[70]
M. Kunowsky, B. Weinberger, F. L. Darkrim, F. Suárez-García, D. Cazorla-Amorós, and A. Linares-Solano, “Impact of the carbonisation temperature on the activation of carbon fibres and their application for hydrogen storage,” International Journal of Hydrogen Energy, vol. 33, no. 12, pp. 3091–3095, 2008.
[71]
L. Zubizarreta, A. Arenillas, and J. J. Pis, “Carbon materials for H2 storage,” International Journal of Hydrogen Energy, vol. 34, pp. 4575–4581, 2009.
[72]
G. Rodríguez-Blanco, L. Giraldo, and J. C. Moreno-Piraján, “Carbon molecular sieves from carbon cloth: influence of the chemical impregnant on gas separation properties,” Applied Surface Science, vol. 256, pp. 5221–5225, 2010.
[73]
F. Salvador, M. J. Sánchez-Montero, J. Montero, and C. Izquierdo, “Activated carbon fibers prepared from a phenolic fiber by supercritical water and steam activation,” Journal of Physical Chemistry C, vol. 112, pp. 20057–20064, 2008.
[74]
M. J. Sánchez-Montero, F. Salvador, and C. Izquierdo, “Reactivity and porosity of a carbon fiber activated with supercritical CO2,” Journal of Physical Chemistry C, vol. 112, no. 13, pp. 4991–4999, 2008.
[75]
J. L. Figueiredo, N. Mahata, M. F. R. Pereira, M. J. S. Montero, J. Montero, and F. Salvador, “Adsorption of phenol on supercritically activated carbon fibres: effect of texture and surface chemistry,” Journal of Colloid and Interface Science, vol. 357, no. 1, pp. 210–214, 2011.
[76]
P. T. Williams and A. R. Reed, “High grade activated carbon matting derived from the chemical activation and pyrolysis of natural fibre textile waste,” Journal of Analytical and Applied Pyrolysis, vol. 71, no. 2, pp. 971–986, 2004.
[77]
A. C. Pastor, F. Rodríguez-Reinoso, H. Marsh, and M. A. Martínez, “Preparation of activated carbon cloths from viscous rayon. Part I. Carbonization procedures,” Carbon, vol. 37, pp. 1275–1283, 1999.
[78]
F. Rodriguez-Reinoso, A. C. Pastor, H. Marsh, and M. A. Martínez, “Preparation of activated carbon cloths from viscous rayon. Part II: physical activation processes,” Carbon, vol. 38, pp. 379–395, 2000.
[79]
F. Rodríguez-Reinoso, A. C. Pastor, H. Marsh, and A. Huidobro, “Preparation of activated carbon cloths from viscous rayon. Part III. Effect of carbonization on CO2 activation,” Carbon, vol. 38, no. 3, pp. 397–406, 2000.
[80]
A. Huidobro, A. C. Pastor, and F. R. Reinoso, “Preparation of activated carbon cloth from viscous rayon. Part IV: chemical activation,” Carbon, vol. 38, pp. 389–398, 2001.
[81]
M. C. B. López, A. Martínez-Alonso, and J. M. D. Tascón, “Microporous texture of activated carbon fibres prepared from Nomex aramid fibres,” Microporous and Mesoporous Materials, vol. 34, no. 2, pp. 171–179, 2000.
[82]
F. Suárez-García, A. Martínez-Alonso, and J. M. D. Tascón, “Beneficial effects of phosphoric acid as an additive in the preparation of activated carbon fibers from Nomex aramid fibers by physical activation,” Fuel Processing Technology, vol. 77-78, pp. 237–244, 2002.
[83]
F. Suárez-García, A. Martínez-Alonso, and J. M. D. Tascón, “Activated carbon fibers from Nomex by chemical activation with phosphoric acid,” Carbon, vol. 42, pp. 1419–1426, 2004.
[84]
M. Wu, Q. Zha, J. Qiu, Y. Guo, H. Shang, and A. Yuan, “Preparation and characterization of porous carbons from PAN-based preoxidized cloth by KOH activation,” Carbon, vol. 42, no. 1, pp. 205–210, 2004.
[85]
Y. V. Basova, D. D. Edie, P. Y. Badheka, and H. C. Bellam, “The effect of precursor chemistry and preparation conditions on the formation of pore structure in metal-containing carbon fibers,” Carbon, vol. 43, no. 7, pp. 1533–1545, 2005.
[86]
S. Villar-Rodil, R. Navarrete, R. Denoyel et al., “Carbon molecular sieve cloths prepared by chemical vapour deposition of methane for separation of gas mixtures,” Microporous and Mesoporous Materials, vol. 77, no. 2-3, pp. 109–118, 2005.
[87]
J. P. Boudou, P. Parent, F. Suarez-García, S. Villar-Rodil, A. Martínez-Alonso, and J. M. D. Tascón, “Nitrogen in aramid-based activated carbon fibers by TPD, XPS and XANES,” Carbon, vol. 44, pp. 2452–2462, 2006.
[88]
C. Liu, W. Dong, J. Song, and L. Liu, “Evolution of microstructure and properties of phenolic fibers during carbonization,” Materials Science and Engineering A, vol. 459, pp. 347–354, 2007.
[89]
S. J. Zhang, H. M. Feng, J. P. Wang, and H. Q. Yu, “Structure evolution and optimization in the fabrication of PVA-based activated carbon fibres,” Journal of Colloid and Interface Science, vol. 321, pp. 96–102, 2008.
[90]
H. M. Feng, S. J. Zhang, Y. Z. Chen, Y. W. Ding, H. Q. Yu, and M. H. W. Lam, “Fabrication and evaluation of mesoporous poly(vinyl alcohol)-based activated carbon fibers,” Industrial and Engineering Chemistry Research, vol. 48, no. 7, pp. 3398–3402, 2009.
[91]
A. Castro-Mu?iz, A. Martínez-Alonso, and J. M. D. Tascón, “Effect of PPTA pre-impregnation with phosphoric acid on the porous texture of carbons prepared by CO2 activation of PPTA chars,” Microporous and Mesoporous Materials, vol. 119, no. 1–3, pp. 284–289, 2009.
[92]
Y. Geng, Y. Song, M. Zhong, P. Li, Q. G. Guo, and L. Liu, “Investigation of preparation and electrochemical performance of phenolic resin based activated carbon cloth,” Journal of Materials Engineering, vol. 10, pp. 1–4, 2011.
[93]
M. B. Vázquez-Santos, A. Martínez-Alonso, and J. M. D. Tascón, “Activated carbon fibers from poly(p-phenylene benzobisoxazole),” Carbon, vol. 46, pp. 818–832, 2008.
[94]
M. B. Vázquez-Santos, F. Suárez-García, A. Martínez-Alonso, and J. M. D. Tascón, “Activated carbon fibers with a high heteroatom content by chemical activation of PBO with phosphoric acid,” Langmuir, vol. 28, pp. 5850–5860, 2012.
[95]
K. Babe?, “Porous structure evolution of cellulose carbon fibres during heating in the initial activation stage,” Fuel Processing Technology, vol. 85, pp. 75–89, 2003.
[96]
J. A. Maciá-Agulló, B. C. Moore, D. Cazorla-Amorós, and A. Linares-Solano, “Influence of carbon fibres crystallinities on their chemical activation by KOH and NaOH,” Microporous and Mesoporous Materials, vol. 101, no. 3, pp. 397–405, 2007.
[97]
P. J. M. Carrott, J. M. V. Nabais, M. M. L. R. Carrott, and J. A. Pajares, “Preparation of activated carbon fibres from acrylic textile fibres,” Carbon, vol. 39, no. 10, pp. 1543–1555, 2001.
[98]
P. J. M. Carrott, J. M. V. Nabais, M. M. L. R. Carrott, and J. A. Menéndez, “Thermal treatments of activated carbon fibres using a microwave furnace,” Microporous and Mesoporous Materials, vol. 47, no. 2-3, pp. 243–252, 2001.
[99]
J. M. V. Nabais, P. J. M. Carrott, and M. M. L. R. Carrott, “From commercial textile fibres to activated carbon fibres: chemical transformations,” Materials Chemistry and Physics, vol. 93, no. 1, pp. 100–108, 2005.
[100]
J. M. V. Nabais, T. Canário, P. J. M. Carrott, and M. M. L. R. Carrott, “Production of activated carbon cloth with controlled structure and porosity from a new precursor,” Journal of Porous Materials, vol. 14, no. 2, pp. 181–190, 2007.
[101]
J. M. V. Nabais, P. J. M. Carrott, M. M. L. R. Carrott, and J. A. Menéndez, “Preparation and modification of activated carbon fibres by microwave heating,” Carbon, vol. 42, pp. 1315–1320, 2004.
[102]
S. Y. You, Y. H. Park, and C. R. Park, “Preparation and properties of activated carbon fabric from acrylic fabric waste,” Carbon, vol. 38, no. 10, pp. 1453–1460, 2000.
[103]
P. T. Williams and A. R. Reed, “Pre-formed activated carbon matting derived from the pyrolysis of biomass natural fibre textile waste,” Journal of Analytical and Applied Pyrolysis, vol. 70, no. 2, pp. 563–577, 2003.
[104]
P. T. Williams and A. R. Reed, “Development of activated carbon pore structure via physical and chemical activation of biomass fibre waste,” Biomass and Bioenergy, vol. 30, no. 2, pp. 144–152, 2006.
[105]
M. A. Nahil and P. T. Williams, “Activated carbons from acrylic textile waste,” Journal of Analytical and Applied Pyrolysis, vol. 89, no. 1, pp. 51–59, 2010.
[106]
M. A. Nahil and P. T. Williams, “Surface chemistry and porosity of nitrogen-containing activated carbons produced from acrylic textile waste,” Chemical Engineering Journal, vol. 184, pp. 228–237, 2012.
[107]
M. Olivares-Marín, S. García, C. Pevida, M. S. Wong, and M. Maroto-Valer, “The influence of the precursor and synthesis method on the CO2 capture capacity of carpet waste-based sorbents,” Journal of Environmental Management, vol. 92, no. 10, pp. 2810–2817, 2011.
[108]
R. Yang, H. Yu, L. Luo et al., “Pore structure of hemp cloth-derived carbon fibers activated by zinc chloride,” Journal of Beijing University of Chemical Technology, vol. 37, no. 5, pp. 44–50, 2010.
[109]
M. E. Ramos, J. D. Gonzalez, P. R. Bonelli, and A. L. Cukierman, “Effect of process conditions on physicochemical and electrical characteristics of denim-based activated carbon cloths,” Industrial and Engineering Chemistry Research, vol. 46, no. 4, pp. 1167–1173, 2007.
[110]
M. E. Ramos, P. R. Bonelli, and A. L. Cukierman, “Physico-chemical and electrical properties of activated carbon cloths. Effect of inherent nature of the fabric precursor,” Colloids and Surfaces A, vol. 324, no. 1–3, pp. 86–92, 2008.
[111]
M. E. Ramos, P. R. Bonelli, A. L. Cukierman, M. M. L. R. Carrott, and P. J. M. Carrott, “Influence of thermal treatment conditions on porosity development and mechanical properties of activated carbon cloths from a novel nanofibre-made fabric,” Materials Chemistry and Physics, vol. 116, no. 2-3, pp. 310–314, 2009.
[112]
S. Aber, A. Khataee, and M. Sheydaei, “Optimization of activated carbon fiber preparation from Kenaf using K2HPO4 as chemical activator for adsorption of phenolic compounds,” Bioresource Technology, vol. 100, no. 24, pp. 6586–6591, 2009.
[113]
M. E. Ramos, P. R. Bonelli, S. Blacher, M. M. L. R. Carrott, P. J. M. Carrott, and A. L. Cukierman, “Effect of the activating agent on physico-chemical and electrical properties of activated carbon cloths developed from a novel cellulosic precursor,” Colloids and Surfaces A, vol. 378, no. 1–3, pp. 87–93, 2011.
[114]
M. C. Basso, E. G. Cerrella, and A. L. Cukierman, “Activated carbons developed from a rapidly renewable biosource for removal of cadmium(II) and nickel(II) ions from dilute aqueous solutions,” Industrial and Engineering Chemistry Research, vol. 41, no. 2, pp. 180–189, 2002.
[115]
M. C. Basso, E. G. Cerrella, and A. L. Cukierman, “Lignocellulosic materials as potential biosorbents of trace toxic metals from wastewater,” Industrial and Engineering Chemistry Research, vol. 41, no. 15, pp. 3580–3585, 2002.
[116]
A. L. Cukierman, “Metal ion biosorption potential of lignocellulosic biomasses and marine algae for wastewater treatment,” Adsorption Science and Technology, vol. 25, no. 3-4, pp. 227–244, 2007.
[117]
M. Betancur, P. R. Bonelli, J. Velásquez, and A. L. Cukierman, “Potentiality of lignin from the Kraft pulping process for removal of trace nickel from wastewater: effect of demineralisation,” Bioresource Technology, vol. 100, no. 3, pp. 1130–1137, 2009.
[118]
D. A. Nabarlatz, J. de Celis, P. Bonelli, and A. L. Cukierman, “Batch and dynamic sorption of Ni(II) ions by activated carbon based on a native lignocellulosic precursor,” Journal of Environmental Management, vol. 97, pp. 109–115, 2012.
[119]
K. Kadirvelu, C. Faur-Brasquet, and P. Le Cloirec, “Removal of Cu(II), Pb(II), and Ni(II) by adsorption onto activated carbon cloths,” Langmuir, vol. 16, no. 22, pp. 8404–8409, 2000.
[120]
J. R. Rangel-Mendez and M. Streat, “Adsorption of cadmium by activated carbon cloth: influence of surface oxidation and solution pH,” Water Research, vol. 36, no. 5, pp. 1244–1252, 2002.
[121]
A. Afkhami, T. Madrakian, Z. Karimi, and A. Amini, “Effect of treatment of carbon cloth with sodium hydroxide solution on its adsorption capacity for the adsorption of some cations,” Colloids and Surfaces A, vol. 304, no. 1–3, pp. 36–40, 2007.
[122]
A. Afkhami, T. Madrakian, A. Amini, and Z. Karimi, “Effect of the impregnation of carbon cloth with ethylenediaminetetraacetic acid on its adsorption capacity for the adsorption of several metal ions,” Journal of Hazardous Materials, vol. 150, no. 2, pp. 408–412, 2008.
[123]
O. Duman and E. Ayranci, “Attachment of benzo-crown ethers onto activated carbon cloth to enhance the removal of chromium, cobalt and nickel ions from aqueous solutions by adsorption,” Journal of Hazardous Materials, vol. 176, no. 1–3, pp. 231–238, 2010.
[124]
I. D. Harry, B. Saha, and I. W. Cumming, “Effect of electrochemical reduction and oxidation of a viscose rayon based activated carbon cloth for Cr(VI) sorption from aqueous solution,” Industrial and Engineering Chemistry Research, vol. 47, no. 17, pp. 6734–6741, 2008.
[125]
D. Mohan, K. P. Singh, and V. K. Singh, “Removal of hexavalent chromium from aqueous solution using low-cost activated carbons derived from agricultural waste materials and activated carbon fabric cloth,” Industrial and Engineering Chemistry Research, vol. 44, no. 4, pp. 1027–1042, 2005.
[126]
C. Faur-Brasquet, K. Kadirvelu, and P. Le Cloirec, “Removal of metal ions from aqueous solution by adsorption onto activated carbon cloths: adsorption competition with organic matter,” Carbon, vol. 40, no. 13, pp. 2387–2392, 2002.
[127]
C. Moreno-Castilla, M. A. Alvarez-Merino, M. V. López-Ramón, and J. Rivera-Utrilla, “Cadmium ion adsorption on different carbon adsorbents from aqueous solutions. effect of surface chemistry, pore texture, ionic strength, and dissolved natural organic matter,” Langmuir, vol. 20, pp. 8142–8148, 2004.
[128]
M. Goyal, M. Bhagat, and R. Dhawan, “Removal of mercury from water by fixed bed activated carbon columns,” Journal of Hazardous Materials, vol. 171, no. 1–3, pp. 1009–1015, 2009.
[129]
M. A. álvarez-Merino, V. López-Ramón, and C. Moreno-Castilla, “A study of the static and dynamic adsorption of Zn(II) ions on carbon materials from aqueous solutions,” Journal of Colloid and Interface Science, vol. 288, pp. 335–341, 2005.
[130]
R. Leyva-Ramos, P. E. Diaz-Flores, A. Aragon-Pi?a, J. Mendoza-Barron, and R. M. Guerrero-Coronado, “Adsorption of cadmium(II) from an aqueous solution onto activated carbon cloth,” Separation Science and Technology, vol. 40, no. 10, pp. 2079–2094, 2005.
[131]
A. Afkhami, T. Madrakian, and Z. Karimi, “The effect of acid treatment of carbon cloth on the adsorption of nitrite and nitrate ions,” Journal of Hazardous Materials, vol. 144, no. 1-2, pp. 427–431, 2007.
[132]
A. Afkhami, T. Madrakian, and A. Amini, “Mo(VI) and W(VI) removal from water samples by acid-treated high area carbon cloth,” Desalination, vol. 243, no. 1–3, pp. 258–264, 2009.
[133]
B. Saha, I. D. Harry, and U. Siddiqui, “Electrochemically modified viscose-rayon-based activated carbon cloth for competitive and noncompetitive sorption of trace cobalt and lead ions from aqueous solution,” Separation Science and Technology, vol. 44, no. 16, pp. 3950–3972, 2009.
[134]
M. Goyal and M. Bhagat, “Dynamic adsorption of Pb(II) ions from aqueous solution using activated carbon beds,” Indian Journal of Engineering and Materials Sciences, vol. 17, no. 5, pp. 367–372, 2010.
[135]
C. Moreno-Castilla, “Adsorption of organic solutes from dilute aqueous solutions,” in Adsorption By Carbons, E. J. Bottani and J. M. D. Tascón, Eds., Chapter 25, pp. 653–678, Elsevier, Oxford, UK, 2008.
[136]
H. Métivier-Pignon, C. Faur-Brasquet, and P. Le Cloirec, “Adsorption of dyes onto activated carbon cloths: approach of adsorption mechanisms and coupling of ACC with ultrafiltration to treat coloured wastewaters,” Separation and Purification Technology, vol. 31, no. 1, pp. 3–11, 2003.
[137]
H. Métivier-Pignon, C. Faur, and P. L. Cloirec, “Adsorption of dyes onto activated carbon cloth: using QSPRs as tools to approach adsorption mechanisms,” Chemosphere, vol. 66, no. 5, pp. 887–893, 2007.
[138]
N. Hoda, E. Bayram, and E. Ayranci, “Kinetic and equilibrium studies on the removal of acid dyes from aqueous solutions by adsorption onto activated carbon cloth,” Journal of Hazardous Materials, vol. 137, no. 1, pp. 344–351, 2006.
[139]
S. Aber and M. Sheydaei, “Removal of COD from industrial effluent containing Indigo dye using adsorption method by activated carbon cloth: optimization, kinetic, and isotherm studies,” Clean—Soil, Air, Water, vol. 40, no. 1, pp. 87–94, 2012.
[140]
O. Duman and E. Ayranci, “Adsorptive removal of cationic surfactants from aqueous solutions onto high-area activated carbon cloth monitored by in situ UV spectroscopy,” Journal of Hazardous Materials, vol. 174, no. 1–3, pp. 359–367, 2010.
[141]
E. Ayranci and O. Duman, “Removal of anionic surfactants from aqueous solutions by adsorption onto high area activated carbon cloth studied by in situ UV spectroscopy,” Journal of Hazardous Materials, vol. 148, no. 1-2, pp. 75–82, 2007.
[142]
E. Ayranci and N. Hoda, “Adsorption kinetics and isotherms of pesticides onto activated carbon-cloth,” Chemosphere, vol. 60, no. 11, pp. 1600–1607, 2005.
[143]
P. E. Diaz-Flores, R. Leyva-Ramos, R. M. Guerrero-Coronado, and J. Mendoza-Barron, “Adsorption of pentachlorophenol from aqueous solution onto activated carbon fiber,” Industrial and Engineering Chemistry Research, vol. 45, no. 1, pp. 330–336, 2006.
[144]
M. V. López-Ramón, M. A. Fontecha-Cámara, M. A. Alvarez-Merino, and C. Moreno-Castilla, “Removal of diuron and amitrole from water under static and dynamic conditions using activated carbons in form of fibers, cloth, and grains,” Water Research, vol. 41, pp. 2865–2870, 2007.
[145]
L. M. Pastrana-Martínez, M. V. López-Ramón, and C. Moreno-Castilla, “Adsorption and thermal desorption of the herbicide fluroxypyr on activated carbon fibers and cloth at different pH values,” Journal of Colloid and Interface Science, vol. 331, no. 1, pp. 2–7, 2009.
[146]
L. M. Pastrana-Martínez, M. V. López-Ramón, M. A. Fontecha-Cámara, and C. Moreno-Castilla, “Batch and column adsorption of herbicide fluroxypyr on different types of activated carbons from water with varied degrees of hardness and alkalinity,” Water Research, vol. 44, pp. 879–885, 2010.
[147]
C. Moreno-Castilla, M. V. López-Ramón, L. M. Pastrana-Martínez, M. A. álvarez-Merino, and M. A. Fontecha-Cámara, “Competitive adsorption of the herbicide fluroxypyr and tannic acid from distilled and tap water on activated carbons and their thermal desorption,” Adsorption, vol. 18, pp. 173–179, 2012.
[148]
C. Moreno-Castilla, M. A. Fontecha-Cámara, M. A. álvarez-Merino, M. V. López-Ramón, and F. Carrasco-Marín, “Activated carbon cloth as adsorbent and oxidation catalyst for the removal of amitrole from aqueous solution,” Adsorption, vol. 17, pp. 413–419, 2011.
[149]
I. P. P. Cansado, P. A. M. Mour?o, A. I. Falc?o, M. M. L. R. Carrott, and P. J. M. Carrott, “The influence of the activated carbon post-treatment on the phenolic compounds removal,” Processing Technology, vol. 103, pp. 64–70, 2012.
[150]
E. Bayram, N. Hoda, and E. Ayranci, “Adsorption/electrosorption of catechol and resorcinol onto high area activated carbon cloth,” Journal of Hazardous Materials, vol. 168, no. 2-3, pp. 1459–1466, 2009.
[151]
E. Ayranci and O. Duman, “Adsorption of aromatic organic acids onto high area activated carbon cloth in relation to wastewater purification,” Journal of Hazardous Materials, vol. 136, no. 3, pp. 542–552, 2006.
[152]
O. Duman and E. Ayranci, “Structural and ionization effects on the adsorption behaviors of some anilinic compounds from aqueous solution onto high-area carbon-cloth,” Journal of Hazardous Materials, vol. 120, no. 1–3, pp. 173–181, 2005.
[153]
E. Ayranci and E. Bayram, “Adsorption of phthalic acid and its esters onto high-area activated carbon-cloth studied by in situ UV-spectroscopy,” Journal of Hazardous Materials, vol. 122, no. 1-2, pp. 147–153, 2005.
[154]
E. Ayranci and O. Duman, “Structural effects on the interactions of benzene and naphthalene sulfonates with activated carbon cloth during adsorption from aqueous solutions,” Chemical Engineering Journal, vol. 156, no. 1, pp. 70–76, 2010.
[155]
R. Leyva-Ramos, R. Ocampo-Perez, and J. Mendoza-Barron, “External mass transfer and hindered diffusion of organic compounds in the adsorption on activated carbon cloth,” Chemical Engineering Journal, vol. 183, pp. 141–151, 2012.
[156]
P. Alonso-Davila, O. L. Torres-Rivera, R. Leyva-Ramos, and R. Ocampo-Perez, “Removal of pyridine from aqueous solution by adsorption on an activated carbon cloth,” Clean—Soil, Air, Water, vol. 40, no. 1, pp. 45–53, 2012.
[157]
P. Monneyron, C. Faur-Brasquet, A. Sakoda, M. Suzuki, and P. Le Cloirec, “Competitive adsorption of organic micropollutants in the aqueous phase onto activated carbon cloth: comparison of the IAS model and neural networks in modeling data,” Langmuir, vol. 18, no. 13, pp. 5163–5169, 2002.
[158]
R. Srinivasan and G. A. Sorial, “Adsorption of geosmin and MIB on activated carbon fibers-single and binary solute system,” Water, Air, and Soil Pollution, vol. 9, no. 3, pp. 223–235, 2009.
[159]
M. E. Fernandez, G. V. Nunell, P. R. Bonelli, and A. L. Cukierman, “Effectiveness of Cupressus sempervirens cones as biosorbent for the removal of basic dyes from aqueous solutions in batch and dynamic modes,” Bioresource Technology, vol. 101, no. 24, pp. 9500–9507, 2010.
[160]
M. E. Fernandez, G. V. Nunell, P. R. Bonelli, and A. L. Cukierman, “Batch and dynamic biosorption of basic dyes from binary solutions by alkaline-treated cypress cone chips,” Bioresource Technology, vol. 106, pp. 55–62, 2012.
[161]
P. Ravichandran, A. Sowmya, and S. Meenakshi, “Equilibrium and kinetic studies on the removal of basic violet 10 from aqueous solutions using activated carbons prepared from industrial wastes,” Bioremediation Journal, vol. 16, no. 2, pp. 86–96, 2012.
[162]
E. Ayranci and N. Hoda, “Adsorption of bentazon and propanil from aqueous solutions at the high area activated carbon-cloth,” Chemosphere, vol. 57, no. 8, pp. 755–762, 2004.
[163]
G. Kyriakopoulos and D. Doulia, “Adsorption of pesticides on carbonaceous and polymeric materials from aqueous solutions: a review,” Separation and Purification Reviews, vol. 35, no. 3, pp. 97–191, 2006.
[164]
E. Ayranci and N. Hoda, “Studies on removal of metribuzin, bromacil, 2,4-D and atrazine from water by adsorption on high area carbon cloth,” Journal of Hazardous Materials, vol. 112, no. 1-2, pp. 163–168, 2004.
[165]
A. D?browski, P. Podko?cielny, Z. Hubicki, and M. Barczak, “Adsorption of phenolic compounds by activated carbon—a critical review,” Chemosphere, vol. 58, pp. 1049–1070, 2005.
[166]
E. Ayranci and O. Duman, “Adsorption behaviors of some phenolic compounds onto high specific area activated carbon cloth,” Journal of Hazardous Materials, vol. 124, no. 1–3, pp. 125–132, 2005.
[167]
E. Ayranci, N. Hoda, and E. Bayram, “Adsorption of benzoic acid onto high specific area activated carbon cloth,” Journal of Colloid and Interface Science, vol. 284, no. 1, pp. 83–88, 2005.
[168]
T. Vasiljevi?, J. Spasojevi?, M. Ba?i?, A. Onjia, and M. Lau?evi?, “Adsorption of phenol and 2, 4-dinitrophenol on activated carbon cloth: the influence of sorbent surface acidity and pH,” Separation Science and Technology, vol. 41, pp. 1061–1075, 2006.
[169]
Z. Hashisho, M. Rood, and L. Botich, “Microwave-swing adsorption to capture and recover vapors from air streams with activated carbon fiber cloth,” Environmental Science and Technology, vol. 39, no. 17, pp. 6851–6859, 2005.
[170]
D. Ramirez, S. Qi, M. J. Rood, and K. J. Hay, “Equilibrium and heat of adsorption for organic vapors and activated carbons,” Environmental Science & Technology, vol. 39, pp. 5864–5871, 2005.
[171]
L. M. Le Leuch, A. Subrenat, and P. Le Cloirec, “Hydrogen sulfide adsorption and oxidation onto activated carbon cloths: applications to odorous gaseous emission treatments,” Langmuir, vol. 19, no. 26, pp. 10869–10877, 2003.
[172]
J. P. Boudou, “Surface chemistry of a viscose-based activated carbon cloth modified by treatment with ammonia and steam,” Carbon, vol. 41, no. 10, pp. 1955–1963, 2003.
[173]
J. P. Boudou, M. Chehimi, E. Broniek, T. Siemieniewska, and J. Bimer, “Adsorption of H2S or SO2 on an activated carbon cloth modified by ammonia treatment,” Carbon, vol. 41, no. 10, pp. 1999–2007, 2003.
[174]
P. Sullivan, J. Moate, B. Stone, J. D. Atkinson, Z. Hashisho, and M. J. Rood, “Physical and chemical properties of PAN-derived electrospun activated carbon nanofibers and their potential for use as an adsorbent for toxic industrial chemicals,” Adsorption, vol. 18, pp. 265–274, 2012.
[175]
P. D. Sullivan, M. J. Rood, G. Grevillot, J. D. Wander, and K. J. Hay, “Activated carbon fiber cloth electrothermal swing adsorption system,” Environmental Science and Technology, vol. 38, no. 18, pp. 4865–4877, 2004.
[176]
Y. C. Chiang, C. Y. Lee, and H. C. Lee, “Surface chemistry of polyacrylonitrile- and rayon-based activated carbon fibers after post-heat treatment,” Materials Chemistry and Physics, vol. 101, no. 1, pp. 199–210, 2007.
[177]
M. E. Ramos, P. R. Bonelli, A. L. Cukierman, M. M. L. R. Carrott, and P. J. M. Carrott, “Adsorption of volatile organic compounds onto activated carbon cloths derived from a novel regenerated cellulosic precursor,” Journal of Hazardous Materials, vol. 177, no. 1–3, pp. 175–182, 2010.
[178]
E. M. Carter, L. E. Katz, G. E. Speitel Jr., and D. Ramirez, “Gas-phase formaldehyde adsorption isotherm studies on activated carbon: correlations of adsorption capacity to surface functional group density,” Environmental Science and Technology, vol. 45, no. 15, pp. 6498–6503, 2011.
[179]
X. Fan, C. Li, G. Zeng et al., “Removal of gas-phase element mercury by activated carbon fiber impregnated with CeO2,” Energy and Fuels, vol. 24, no. 8, pp. 4250–4254, 2010.
[180]
K. P. Singh, D. Mohan, G. S. Tandon, and G. S. D. Gupta, “Vapor-phase adsorption of hexane and benzene on activated carbon fabric cloth: equilibria and rate studies,” Industrial and Engineering Chemistry Research, vol. 41, no. 10, pp. 2480–2486, 2002.
[181]
L. Luo, D. Ramirez, M. J. Rood, G. Grevillot, K. J. Hay, and D. L. Thurston, “Adsorption and electrothermal desorption of organic vapors using activated carbon adsorbents with novel morphologies,” Carbon, vol. 44, no. 13, pp. 2715–2723, 2006.
[182]
G. Y. Oh, Y. W. Ju, M. Y. Kim, H. R. Jung, H. J. Kim, and W. J. Lee, “Adsorption of toluene on carbon nanofibers prepared by electrospinning,” The Science of the Total Environment, vol. 393, pp. 341–347, 2008.
[183]
M. A. Lillo-Ródenas, D. Cazorla-Amorós, and A. Linares-Solano, “Benzene and toluene adsorption at low concentration on activated carbon fibres,” Adsorption, vol. 17, no. 3, pp. 473–481, 2011.
[184]
M. Yao, Q. Zhang, D. W. Hand, D. Perram, and R. Taylor, “Adsorption and regeneration on activated carbon fiber cloth for volatile organic compounds at indoor concentration levels,” Journal of the Air and Waste Management Association, vol. 59, no. 1, pp. 31–36, 2009.
[185]
A. S. Subrenat and P. A. Le Cloirec, “Volatile organic compound (VOC) removal by adsorption onto activated carbon fiber cloth and electrothermal desorption: an industrial application,” Chemical Engineering Communications, vol. 193, no. 4, pp. 478–486, 2006.
[186]
C. Faur-Brasquet and P. Le Cloirec, “Modelling of the flow behavior of activated carbon cloths using a neural network approach,” Chemical Engineering and Processing, vol. 42, no. 8-9, pp. 645–652, 2003.
[187]
B. Boulinguiez and P. Le Cloirec, “Adsorption on activated carbons of five selected volatile organic compounds present in biogas: comparison of granular and fiber cloth materials,” Energy and Fuels, vol. 24, no. 9, pp. 4756–4765, 2010.
[188]
D. L. Johnsen, K. E. Mallouk, and M. J. Rood, “Control of electrothermal heating during regeneration of activated carbon fiber cloth,” Environmental Science and Technology, vol. 45, no. 2, pp. 738–743, 2011.
[189]
D. L. Johnsen and M. J. Rood, “Temperature control during regeneration of activated carbon fiber cloth with resistance-feedback,” Environmental Science & Technology, vol. 46, pp. 11305–11312, 2012.
[190]
H. Emamipour, Z. Hashisho, D. Cevallos et al., “Steady-state and dynamic desorption of organic vapor from activated carbon with electrothermal swing adsorption,” Environmental Science and Technology, vol. 41, no. 14, pp. 5063–5069, 2007.
[191]
Z. Hashisho, M. J. Rood, S. Barot, and J. Bernhard, “Role of functional groups on the microwave attenuation and electric resistivity of activated carbon fiber cloth,” Carbon, vol. 47, no. 7, pp. 1814–1823, 2009.
[192]
M. Lordgooei and M. S. Kim, “Modeling volatile organic compound sorption in activated carbon. II: multicomponent equilibrium,” Journal of Environmental Engineering, vol. 130, no. 3, pp. 223–230, 2004.