Green inhibitors are promising alternatives to toxic corrosion inhibitors as they are environmentally safe substances, ecologically acceptable and renewable. In this research, the effect of green henna as an inhibitor existing in the coating of TMSM-PMMA and its electrochemical study were analyzed. The coating was produced by “sol-gel” method in order to protect the corrosion of low-carbon steel. TMSM hybrid cell was synthesized by hydrolysis and condensation, Metaacryloxypropyltrimethoxysilane and Tetraetylorthosilicate with 1:1 molar ratio and PMMA hybrid cell was produced by Methylmetaacrylate polymerization. Finally two cells were mixed in 1:1 weight ratio. The carbon steel substrates were prepared by dip coating method. SEM technique was applied for the microstructure evaluation of thin layers including different concentrations of henna extract. Adhesion of coating was analyzed by “Pull off” test. Additionally, the experimental results obtained in different concentrations of henna extract using electrochemical methods such as tafel polarization, electrochemical impedance spectroscopy indicating that coating with the concentration of 3% inhibitor had a high level of inhibition efficiency in 0.1 M HCL. The results of polarization tests signified that henna extract acts as a mixed inhibitor.
References
[1]
Chaudhari, H.G. and Vashi, R.V. (2016) The Study of Henna Leaves Extract as Green Corrosion Inhibitor for Mild Steel in Acetic Acid. Journal of Fundamental and Applied Sciences, 8, 280-296. https://doi.org/10.4314/jfas.v8i2.8
[2]
Mojtaba, N.E., Pourriahi, M., Motalebi, A. and Zendehdel, M. (2013) Improvement of the Corrosion Performance of 304 L Stainless Steel by a Nanostructure Hybrid Coating/Henna Extract. Anti-Corrosion Methods and Materials, 61, 1-9.
https://doi.org/10.1108/ACMM-12-2012-1229
[3]
Toxicological Profile for Chromium, ATDSR/Tp-88/10 (1989) US Public Service, Washington, DC, Agency for Toxic Substances.
[4]
Motalebi, A., Nasr-Esfahani, M., Ali, R. and Pourriahi, M. (2012) Improvement of Corrosion Performance of 316 L Stainless Steel via PVTMS/Henna Thin Film. Progress in Natural Science: Materials International, 22, 392-400.
https://doi.org/10.1016/j.pnsc.2012.10.006
[5]
Fedel, M., Olivier, M., Poelman, M., Deflorian, F., Rossi, S. and Druart, M.E. (2009) Corrosion Protection Properties of Silane Pre-Treated Powder Coated Galvanized Steel. Progress in Organic Coatings, 66, 118-128.
https://doi.org/10.1016/j.porgcoat.2009.06.011
[6]
Bajat, J.B., Milosev, I., Jovanovic, Z., Jancic-Heinemann, R.M., Dimitrijevic, M. and Miskovic-Stankovic, V.B. (2010) Corrosion Protection of Aluminium Pretreated by Vinyltriethoxysilane in Sodium Chloride Solution. Corrosion Science, 52, 1060-1069.
https://doi.org/10.1016/j.corsci.2009.11.035
[7]
Cambon, J.B., Ansart, F., Bonino, J.P. and Turq, V. (2012) Effect of Cerium Concentration on Corrosion Resistance and Polymerization of Hybrid Sol-Gel Coating on Martensitic Stainless Steel. Progress in Organic Coatings, 75, 486-493.
https://doi.org/10.1016/j.porgcoat.2012.06.005
[8]
Paula, P. and Heidi, M.F. (2001) Performance of Silane Treated Primed Hot-Dip Galvanised Steel. Anti-Corrosion Methods and Materials, 48, 7-17.
https://doi.org/10.1108/00035590110365273
[9]
Hassannejad, H., Moghaddasi, M., Saebnoori, E. and Rabiei Baboukani, A. (2017) Microstructure, Deposition Mechanism and Corrosion Behavior of Nanostructured Cerium Oxide Conversion Coating Modified with Chitosan on AA2024 Aluminum Alloy. Journal of Alloys and Compounds, 725, 968-975.
https://doi.org/10.1016/j.jallcom.2017.07.253
[10]
Raps, D., Hack, T., Wehr, J., Zheludkevich, M.L., Bastos, A.C., Ferreira, M.G.S. and Nuyken, O. (2009) Electrochemical Study of Inhibitor-Containing Organic-Inorganic Hybrid Coatings on AA2024. Corrosion Science, 51, 1012-1021.
https://doi.org/10.1016/j.corsci.2009.02.018
[11]
Yasakau, K.A., Zheludkevich, M.L., Karavai, O.V. and Ferreira, M.G.S. (2008) Influence of Inhibitor Addition on the Corrosion Protection Performance of Sol-Gel Coatings on AA2024. Progress in Organic Coatings, 63, 352-361.
https://doi.org/10.1016/j.porgcoat.2007.12.002
[12]
Cheng, Z., Foroughi, P. and Behrens, A. (2017) Synthesis of Nanocrystalline TaC Powders via Single-Step High Temperature Spray Pyrolysis from Solution Precursors. Ceramics International, 43, 3431-3434.
https://doi.org/10.1016/j.ceramint.2016.11.177
[13]
Al-Sehaibani, H. (2000) Evaluation of Extracts of Henna Leaves as Environmentally Friendly Corrosion Inhibitors for Metals. Materialwissenschaft und Werkstofftechnik, 31, 1060-1063.
https://doi.org/10.1002/1521-4052(200012)31:12<1060::AID-MAWE1060>3.0.CO;2-K
[14]
Foroughi, P., Zhang, C., Agarwal, A. and Cheng, Z. (2017) Controlling Phase Separation of TaxHf1-xC Solid Solution Nanopowders during Carbothermal Reduction Synthesis. Journal of the American Ceramic Society, 100, 5056-5065.
https://doi.org/10.1111/jace.15065
[15]
Kunsta, S.R., Cardoso, H.R.P., Oliveira, C.T., Filho, C.I.S., Sarmento, V.H.V., Menezes, T.L., Muller, I.L. and Malfatti, C.F. (2013) Influence of Tetraethoxy Silane Addition in Siloxane-Poly (Methylmethacrylate) Hybrid Films Applied on Galvanized Steel. International Journal of Electrochemical Science, 8, 11984-12004.
[16]
Schottner, G. (2001) Hybrid Sol-Gel-Derived Polymers: Applications of Multifunctional Materials. Chemistry of Materials, 13, 3422-3435.
https://doi.org/10.1021/cm011060m
[17]
Judeinstein, P. and Sanchez, C. (1996) Hybrid Organic-Inorganic Materials: A Land of Multidisciplinarity. Journal of Materials Chemistry, 6, 511-525.
https://doi.org/10.1039/JM9960600511
[18]
Shieh, Y.T., Liu, K.H. and Lin, T.L. (2004) Effect of Supercritical CO2 on Morphology of Compatible Crystalline/Amorphous PEO/PMMA Blends. The Journal of Supercritical Fluids, 28, 101-112. https://doi.org/10.1016/S0896-8446(03)00009-3
[19]
Gu, S., Kondo, T. and Konno, M. (2004) Preparation of Silica-Polystyrene Core-Shell Particles up to Micron Sizes. Journal of Colloid and Interface Science, 272, 314-320. https://doi.org/10.1016/j.jcis.2004.01.056
[20]
Sertchook, H. and Avnir, D. (2003) Submicron Silica/Polystyrene Composite Particles Prepared by a One-Step Sol-Gel Process. Chemistry of Materials, 15, 1690-1694.
https://doi.org/10.1021/cm020980h
[21]
Kim, W.S., Kim, K.S., Eo, Y.J., Yoon, K.B. and Bae, B.S. (2005) Synthesis of Fluorinated Hybrid Material for UV Embossing of a Large Core Optical Waveguide Structure. Journal of Materials Chemistry, 15, 465-469.
https://doi.org/10.1039/b412419g
[22]
Foroughi, P. and Cheng, Z. (2016) Understanding the Morphological Variation in the Formation of B4C via Carbothermal Reduction Reaction. Ceramics International, 42, 15189-15198. https://doi.org/10.1016/j.ceramint.2016.06.126
[23]
Zhu, A., Shi, Z., Cai, A., Zhao, F. and Liao, T. (2008) Synthesis of Core-Shell PMMA-SiO2 Nanoparticles with Suspension-Dispersion-Polymerization in an Aqueous System and Its Effect on Mechanical Properties of PVC Composites. Polymer Testing, 27, 540-547. https://doi.org/10.1016/j.polymertesting.2007.11.005
[24]
Delattre, L., Dupuy, C. and Babonneau, F. (1994) Characterization of the Hydrolysis and Polymerization Processes of Methacryloxypropyltrimethoxysilane. Journal of Sol-Gel Science and Technology, 2, 185-188. https://doi.org/10.1007/BF00486238
[25]
Mansfeld, F. and Kendig, M.W. (1985) Electrochemical Impedance Spectroscopy of Protective Coatings. Materials and Corrosion, 36, 473-483.
https://doi.org/10.1002/maco.19850361102
[26]
Rabiei Baboukani, A., Sharifi, E., Akhavan, S. and Saatchi, A. (2016) Co Complexes as a Corrosion Inhibitor for 316 L Stainless Steel in H2SO4 Solution. Journal of Materials Science and Chemical Engineering, 4, 28-35.
https://doi.org/10.4236/msce.2016.49003
[27]
López, D.A., Simison, D.A. and de Sánchez, S.R. (2003) The Influence of Steel Microstructure on CO2 Corrosion. EIS Studies on the Inhibition Efficiency of Benzimidazole. Electrochimica Acta, 48, 845-854.
https://doi.org/10.1016/S0013-4686(02)00776-4
[28]
Kurniawan, F. and Madurani, K.A. (2015)Electrochemical and Optical Microscopy Study of Red Pepper Seed Oil Corrosion Inhibition by Self-Assembled Monolayers (SAM) on 304 SS. Progress in Organic Coatings, 88, 256-262.
https://doi.org/10.1016/j.porgcoat.2015.07.010
[29]
Quraishi, M.A., Singh, A., Singh, V.K., Yadav, D.K. and Singh, A.K. (2010) Green Approach to Corrosion Inhibition of Mild Steel in Hydrochloric Acid and Sulphuric Acid Solutions by the Extract of Murraya koenigii Leaves. Materials Chemistry and Physics, 122, 114-122. https://doi.org/10.1016/j.matchemphys.2010.02.066
[30]
Hussin, M.H. and Kassim, M.J. (2011) The Corrosion Inhibition and Adsorption Behavior of Uncaria gambir Extract on Mild Steel in 1M HCl. Materials Chemistry and Physics, 125, 461-468. https://doi.org/10.1016/j.matchemphys.2010.10.032
[31]
Rabiei Baboukani, A., Akhavan, S., Rezvani, M., Ebrahimi-Kahrizsangi, R. and Saatchi, A. (2016) Electrochemical Corrosion Behavior of Friction Stir Welded AA6061 in NaCl Solution. Proceedings of Iran International Aluminum Conference, Tehran, 11-12 May 2016.
[32]
Mansfeld, F., Kendig, M.W. and Tsai, S. (1982) Evaluation of Corrosion Behavior of Coated Metals with AC Impedance Measurements. Corrosion, 38, 478-485.
https://doi.org/10.5006/1.3577363
[33]
Akhavan, S., Rabiei Baboukani, A., Saatchi, A., Ebrahimi-Kahrizsangi, R. and Shirmohammadi, S. (2014) Investigating the Anodizing Process of Aluminum Alloys in 0.3M Oxalic Acid and Its Metallurgical and Mechanical Behavior. Proceedings of Iran International Aluminum Conference, Tehran, 25-26 May 2014, 197-201.
[34]
Lorenz, W.J. and Mansfeld, F. (1981) Determination of Corrosion Rates by Electrochemical DC and AC Methods. Corrosion Science, 21, 647-672.
https://doi.org/10.1016/0010-938X(81)90015-9
[35]
Agrawal, R., Adelowo, E., Rabiei Baboukani, A., Villegas, M.F., Henriques, A. and Wang, C. (2017) Electrostatic Spray Deposition-Based Manganese Oxide Films— From Pseudocapacitive Charge Storage Materials to Three-Dimensional Microelectrode Integrands. Nanomaterials, 7, 198. https://doi.org/10.3390/nano7080198
[36]
SaebNoori, E., Navidinejad, A. and Rabiei Baboukani, A. (2016) Mechanism Study and Parameter Optimization of A356 Aluminum Alloy Electrochemical Polishing. Proceedings of Iran International Aluminum Conference, Tehran, 11-12 May 2016.
[37]
Thomson, R.H. (1971) Naturally Occuring Quinones. Press London, New York.
[38]
Rabiei Baboukani, A., Akhavan, S., Saatchi, A., Ebrahimi-Kahrizsangi, R. and Saebnoori, E. (2016) Mechanical Properties of AA2024 In the Presence of Al-Cu Intermetallic Surface Layer. Proceedings of Iran International Aluminum Conference, Tehran, 11-12 May 2016.
[39]
El-Etre, A.Y., Abdallah, M. and El-Tantawy, Z.E. (2005) Corrosion Inhibition of Some Metals using Lawsonia Extract. Corrosion Science, 47, 385-395.
https://doi.org/10.1016/j.corsci.2004.06.006
[40]
Ostovari, A., Hoseinieh, A.M., Peikari, A., Shadizadeh, S.R. and Hashemi, S.J. (2009) Corrosion Inhibition of Mild Steel in 1M HCl Solution by Henna Extract: A Comparative Study of the Inhibition by Henna and Its Constituents (Lawsone, Gallic Acid, α-d-Glucose and Tannic Acid). Corrosion Science, 51, 1935-1949.
https://doi.org/10.1016/j.corsci.2009.05.024
[41]
Peiravi, M., Mote, S.R., Mohanty, M.K. and Liu, J. (2017) Bioelectrochemical Treatment of Acid Mine Drainage (AMD) from an Abandoned Coal Mine under Aerobic Condition. Journal of Hazardous Materials, 333, 329-338.
https://doi.org/10.1016/j.jhazmat.2017.03.045
[42]
Musa, A.Y., Kadhum, A.A.H., Mohamad, A.B. and Takriff, A.S. (2010) Experimental and Theoretical Study on the Inhibition Performance of Triazole Compounds for Mild Steel Corrosion. Corrosion Science, 52, 3331-3340.
https://doi.org/10.1016/j.corsci.2010.06.002
[43]
Peiravi, M., Ackah, L., Guru, R., Mohaty, M., Liu, K., Xu, B., Zhu, X. and Chen, L. (2017) Chemical Extraction of Rare Earth Elements from Coal Ash. Minerals & Metallurgical Processing, 34, 170-177. https://doi.org/10.19150/mmp.7856
[44]
Liu, J., Weinholtz, L., Zheng, L., Peiravi, M., Wu, Y. and Chen, D. (2017) Removal of PFOA in Groundwater by Fe0 and MnO2 Nanoparticles under Visible Light, Journal of Environmental Science and Health, Part A, 52, 1048-1054.
[45]
CRC (2005) Handbook of Chemistry and Physics. Internet Version 2005, CRC Press, Boca Raton.
[46]
Mafi, M., Martin, H. and Adjoudai, M. (2017) High Impulse Noice Intensity Removal in MRI Images. IEEE Signal Processing in Medicine and Biology Symposium, Philadelphia, December 1st.
[47]
Mafi, M. (2012) Integration of Mobile Ad Hoc and WIMAX Networks with Approach of Admission Control and Hand off Combination Applied in Telemedicine Services. American Journal of Scientific Research, 83, 14-24.
[48]
Khakpour, I., Soltani, R. and Sohi, M.H. (2015) Microstructure and High Temperature Oxidation Behaviour of Zr-Doped Aluminide Coatings Fabricated on Nickel-Based Super Alloy. Procedia Materials Science (Supplement C), 11, 515-521.
[49]
Rezayan, A.H., Firoozi, N., Kheirjou, S., Tabatabaei Rezaei, S.J. and Reza Nahid, M. (2017) Synthesis and Characterization of Biodegradable Semi-Interpenetrating Polymer Networks Based on Star-Shaped Copolymers of ε-Caprolactone and Lactide. Iranian Journal of Pharmaceutical Research: IJPR, 16, 63-73.
[50]
Rabiei Baboukani, A., Saatchi, A. and Ebrahimi-Kahrizsangi, R. (2012) Solid State Displacement Reaction Between Ni and CuO in 1000 °C as a High Temperature Composites. The 3rd International Conference on Composites: Characterization, Fabrication and Application, 18-19 December 2012, Tehran.
[51]
Awadallah, O. and Cheng, Z. (2017) Formation of Sel-Gel Based Cu2ZnSnS4 Thin Films using Ppm-Level Hydrogen Sulfide. Thin Solid Films, 625, 122-130.
https://doi.org/10.1016/j.tsf.2017.01.054
