Increasing demands for ultrahigh-strength steels in commercial as well as military applications have raised interest in finding alternatives to the high-cost high-alloyed steel and super-alloys currently used, e.g. the use of economic low-alloy compositions processed via low-cost air induction melting and electroslag refining (ESR). In this work the yield of alloying elements and the removal of the impurities nitrogen, sulphur and phosphorus as a result of electroslag refining (ESR) in a newly developed CrNiMoWMnV ultrahigh-strength steel (UHSS) have been studied in relation to their activities in the molten metal pool. Six experimental heats of CrNiMoWMnV UHSS with different chemical compositions were designed, melted in an induction furnace (IF) and refined using ESR. This was followed by hot forging of the ingots at 1100°C to 950°C. ESR using a CaF2-CaO-Al2O3 slag system led to a high yield in Cr, Ni, Mo, W, Mn and V, while the yield of Si is low. The desulphurization of all six UHSS grades was pronounced with most of the sulphur removed either to the slag or by gas reactions. The degree of dephosphorization was only 5% irrespective of the steel composition. On the other hand, denitrification (removal of nitrogen) was achieved. It ranged from 8% to 63% depending on the steel composition. The yield of the alloying elements and removal of impurities from the steel during ESR depends on the chemical and physical properties of the ESR slag and the activity of the elements in the molten state, taking into account elemental interactions.
References
[1]
Philip, T.V. and Mccaffrey, T.J. (1990) Ultrahigh-Strength Steels. ASM International, Metals Handbook, 10th Edition, Vol. 1, 430-448.
[2]
Maity, S.K. and Kawalla, R. (2011) Ultrahigh-Strength Steel: Development of Mechanical Properties through Controlled Cooling. In: Heat Transfer-Engineering Applications.
[3]
Kömi, J., Karjalainen, P. and Porter, D. (2016) Direct-Quenched Structural Steels. In: Encyclopedia of Iron, Steel, and Their Alloys, 1109-1125.
https://doi.org/10.1081/E-EISA-120049737
[4]
Vaish, A.K., Iyer, G.V.R., De, P.K., Lakra, B.A., Chakrabarti, A.K. and Ramachandrarao, P. (2000) Electroslag Remelting—Its Status, Mechanism and Refining Aspects in the Production of Quality Steels. Journal of Metallurgy and Materials Science, 42, 11-29.
[5]
Duckworth, W.E. and Hoyle, G. (1969) Electro-Slag Refining. Chapman and Hall, London.
[6]
Scholz, U.B.H. (1995) Electroslag Remelting Technologies in the Past and Future. MPT International, 31, 36-43.
[7]
Mattar, T., El-Fawakhry, K., Halfa, H. and Eissa, M. (2008) Effect of Nitrogen Alloying on Sulphur Behaviour during ESR of AISI M41 Steel. Steel Research International, 79, 691-697. https://doi.org/10.1002/srin.200806185
[8]
Mattar, T. (2009) Effect of ESR and Nitrogen Alloying on the Cleanliness of M41 Steel. Journal of Materials Sciences and Technology, 17, 35-46.
[9]
Mattar, T.M.T, Fathy, A.M., El-Faramawy, H.S.R., Eissa, M.M. and El-Fawakhry, K.A.R. (2001) Optimization of Desulphurization of Tool Steels during EAF and ESR Processes. Metal 2001, Ostrava, 1-6.
[10]
Mehrabi, K., Rahimipour, M.R. and Shokuhfar, A. (2005) The Effect of Slag Types and Melting Rate on Electro-Slag Remelting (ESR) Processing. International Journal of Iron & Steel Society of Iran, 2, 37-42.
[11]
Hayashi, M., Sano, N. and Fredriksson, P. (2004) Evaluation of Thermodynamic Activity of a Metallic Oxide in a Ternary Slag from the Sulphide Capacity of the Slag. ISIJ International, 44, 1783-1786.
https://doi.org/10.2355/isijinternational.44.1783
[12]
Eissa, M. and EI-Mohammadi, A. (1998) Effect of Physical Properties of Slag on Sulphur Removal Mechanism during ESR Process. Steel Research International, 69, 413-417. https://doi.org/10.1002/srin.199805573
[13]
Yang, Y., McKague, A.R., Sommerville, I.D. and McLean, A. (1997) Phosphate and Sulphide Capacities of CaO-CaCl2-CaF2 Slags. Canadian Metallurgical Quarterly, 36, 347-354.
[14]
Nasu, M., Mills, K.C., Monaghan, B.J., Jakobsson, A. and Seetharaman, S. (1999) Effect of Slag/Metal Interfacial Tension on Kinetics of Dephosphorisation. Ironmaking & Steelmaking, 26, 353-357. https://doi.org/10.1179/030192399677211
[15]
Kawai, Y., Nakao, R. and Mori, K. (1984) Dephosphorization of Liquid Iron by CaF2-Base Fluxes. Transactions of the Iron and Steel Institute of Japan, 24, 509-514.
https://doi.org/10.2355/isijinternational1966.24.509
[16]
Hoyle, G. (1983) Electroslag Processes, Principles and Practice. Applied Science Publishers, London/New York.
[17]
Werner, E. (1988) Solid Solution and Grain Size Hardening of Nitrogen-Alloyed Austenitic Steels. Materials Science and Engineering: A, 101, 93-98.
https://doi.org/10.1016/0921-5093(88)90054-8
[18]
Di Schino, A. and Kenny, J.M. (2003) Grain Refinement Strengthening of a Micro-Crystalline High Nitrogen Austenitic Stainless Steel. Materials Letters, 57, 1830-1834. https://doi.org/10.1016/S0167-577X(02)01076-5
[19]
Gavriljuk, V.G., Berns, H., Escher, C., Glavatskaya, N.I., Sozinov, A. and Petrov, Y.N. (1999) Grain Boundary Strengthening in Austenitic Nitrogen Steels. Materials Science and Engineering: A, 271, 14-21.
https://doi.org/10.1016/S0921-5093(99)00272-5
[20]
Speidel, M.O. (2005) New Nitrogen-Bearing Austenitic Stainless Steels with High Strength and Ductility. Metal Science and Heat Treatment, 47, 489-493.
https://doi.org/10.1007/s11041-006-0017-y
[21]
Ikegami, Y. and Nemoto, R. (1996) Effect of Thermo-Mechanical Treatment on Mechanical Properties of High-Nitrogen Con-taining Cr-Mn-Ni Austenitic Stainless Steels. ISIJ International, 36, 855-861.
https://doi.org/10.2355/isijinternational.36.855
[22]
Fréchard, S., Redjaimia, A., Lach, E. and Lichtenberger, A. (2006) Mechanical Behaviour of Nitrogen-Alloyed Austenitic Stainless Steel Hardened by Warm Rolling. Materials Science and Engineering: A, 415, 219-224.
https://doi.org/10.1016/j.msea.2005.09.070
[23]
Ito, K. and Fruehan, R.J. (1988) Thermodynamics of Nitrogen in CaO-SiO2-AI2O3 Slags and Its Reaction with Fe-C Sat Melts. Metallurgical Transactions B, 19, 419-425. https://doi.org/10.1007/BF02657739
[24]
Min, D.J. and Fruehan, R.J. (1990) Nitrogen Solution in BaO-B2O3 and CaO-B2O3 Slags. Metallurgical Transactions B, 21, 1025-1032.
https://doi.org/10.1007/BF02670273
[25]
Mulfinger, H.O. (1966) Physical and Chemical Solubility of Nitrogen in Glass Melts. Journal of the American Ceramic Society, 49, 462-467.
https://doi.org/10.1111/j.1151-2916.1966.tb13300.x
[26]
Sohn, I., Min, D.J. and Park, J.H. (1999) Thermodynamic Study on the Effect of CaF2 on the Nitrogen and Carbon Solubility in the CaO-Al2O3-CaF2 Slag System. Steel Research International, 70, 215-220. https://doi.org/10.1002/srin.199905629
[27]
Eloy, M.R. and Sano, N. (1990) Nitrogen Solubility in CaO-SiO2, CaO-MgO-SiO2, and BaO-MgO-SiO2 Melts. Metallurgical and Materials Transactions B, 21, 97-104.
https://doi.org/10.1007/BF02658120
[28]
Nafziger, R.H. (1976) Electroslag Melting Process (No. PB-263219; BM-B-669) Bureau of Mines. Albany Metallurgy Research Center, Albany.
[29]
Mattar, T. (2002) Electro-Slag Remelting of AISI M41 High-Speed Tool Steel Scrap. 6th International Tooling Conference, Karlstad, 10-13.
[30]
Chen, J.X. (1990) Iron and Steel Metallurgy: Steelmaking Part. Metallurgical Industry Press, Beijing, 90. (In Chinese)
[31]
Halfa, H. (2003) Improvement of High-Speed Tool Steel by Using Electro-Slag Remelting Technology. M.Sc. Thesis, Faculty of Engineering, Cairo University, Egypt.
[32]
Reitz, J., Maurischat, M., Friedrich, B. and Recycling, M. (2008) Optimized Control of Slag Chemistry for the Electroslag Remelting of Large Size Ingots. 17th International Forge Masters Meeting, 3-7.
[33]
Birol, B. and Saridede, M.N. (2016) The Effect of Slag Optical Basicity on Alloying Element Losses of Steel by Electroslag Remelting (ESR). Transactions of the Indian Institute of Metals, 69, 751-757. https://doi.org/10.1007/s12666-015-0549-1
[34]
Engh, T. (1992) Principles of Metal Refining. Oxford University Press, Oxford, 473.
Bandyopadhyay, T.R., Rao, P.K. and Prabhu, N. (2012) Behavior of Alloying Elements during Electro-Slag Remelting of Ultra-high-Strength Steel. Metallurgical & Mining Industry, 4.
[37]
Eissa, M., Mattar, T. and El-Fawakhry, K. (1999) Proceedings of the 5th International Conference on Tooling “Tool Steels in the Next Century”. University of Leoben, Austria, 275.
[38]
Ahmed, A. and Fathy, A. (2008) Effect of Slag Properties and Nitrogen Addition on Behaviour of Alloying Elements during ESR of AISI M41 Tool Steel. Ironmaking & Steelmaking, 35, 458-464. https://doi.org/10.1179/174328108X318356
[39]
Pehlke, R.D. and Elliott, J.F. (1960) Solubility of Nitrogen in Liquid Iron Alloys. 1. Thermodynamics. Transactions of the American Institute of Mining and Metallurgical Engineers, 218, 1088-1101.
[40]
Hajra, J.P. and Divakar, M. (1999) Thermodynamics of Surfaces and Adsorption in the Fe-S, Fe-N, and Fe-SN Systems at 1823 K. Metallurgical and Materials Transactions B, 30, 429-433. https://doi.org/10.1007/s11663-999-0075-9
[41]
Martinez, E.R., Espejo, V.O. and Manjarrez, F. (1993) The Solubility of Nitrogen in the CaO-CaF2-Al2O3 System and Its Relationship with Basicity. ISIJ International, 33, 48-52. https://doi.org/10.2355/isijinternational.33.48
