|
|
- 2015
制造公差对复合材料螺栓连接结构强度分散性的影响
|
Abstract:
为解决由于螺栓和复合材料板制孔制造过程中不可避免的制造公差引起的配合间隙的不同, 而使复合材料螺栓连接钉载分配不同, 从而导致螺栓连接强度分散性的问题, 以英制高锁螺栓和孔板制孔的制造公差为例, 研究不同配合间隙下双剪四钉螺栓连接钉载分配情况, 并进一步采用改进的特征曲线法、改进的强度包线法和渐进损伤模型对螺栓连接结构的强度进行预测, 得到四钉连接失效强度的分散区间分别为[-3.87%, 2.16%]、[-4.01%, 3.95%]和[-3.16%, 5.14%]。结果说明如果紧固件及螺栓孔均符合制造标准, 则其对强度的影响范围不超过6%。 The manufacturing tolerance, which leads to different fit clearances between bolts and composite plate holes, is ineluctable in the manufacture process. Thus diversified pin load distribution of composite bolted joint is present and further results in the strength scatter of the joints. Taking a double-lap four-bolt composite joint with high locked bolts as an example, the influence of the fit clearance on the pin load distribution was investigated by a clearance-based direct stiffness method. Furthermore, the strength scatters of the four-bolt joint stemmed from the manufacturing tolerance have been predicted by a modified characteristic curve method, a modified strength envelope method and a progressive damage model with the dispersion intervals being [-3.87%, 2.16%], [-4.01%, 3.95%] and [-3.16%, 5.14%], respectively, which shows the effect range of the manufacturing tolerance on the strength of the joint is less than 6%, if the fasteners and holes both meet the manufacturing criterion. 国家自然科学基金(11372020)
| [1] | Buket O, Zuleyha A, Ramazan K. A study of the effects of various geometric parameters on the failure strength of pin-loaded woven-glass-fiber reinforced epoxy laminate[J]. Composites Science and Technology, 2001, 61(10): 491-497. |
| [2] | Chang F K, Scott R A, Springer G S. Failure strength of nonlinearly elastic composite laminates containing a pin loaded hole[J]. Journal of Composite Materials, 1984, 18(3): 464-477. |
| [3] | Liu F R, Zhao L B, Saqib M, et al. A modified failure envelope method for failure prediction of multi-bolt composite joints[J]. Composites Science and Technology, 2013, 83: 54-63. |
| [4] | Zhao L B, Qin T L, Zhang J Y, et al. Determination method of stress concentration relief factors for failure prediction of composite multi-bolt joints[J]. Journal of Composite Materials, 2015, 49(14): 1667-1680. |
| [5] | Binnur G K. Effect of the clearance and interference-fit on failure of the pin-loaded composites[J]. Materials and Design, 2010, 31(1): 85-93. |
| [6] | Agarwal B L. Static strength prediction of bolted joint in composite material [J]. AIAA Journal, 1980, 18(11): 1371-1375. |
| [7] | Hart-Smith L J. Bolted joints in graphite-epoxy composites[R]. Long Beach: Douglas Aircraft Company, 1976. |
| [8] | Zhang J Y, Liu F R, Zhao L B, et al. A progressive damage analysis based characteristic length method for multi-bolt composite joints[J]. Composite Structures, 2014, 108: 915-923. |
| [9] | Qin T L, Zhao L B, Zhang J Y. Fastener effects on mechanical behaviors of double-lap composite joints[J]. Composite Structures, 2013, 100: 413-423. |
| [10] | McCarthy M A, McCarthy C T, Padhi G S. A simple method for determining the effects of bolt-hole clearance on load distribution in single-column multi-bolt composite joints[J]. Composite Structures, 2006, 73(1): 78-87. |
| [11] | Zhang J Y, Liu F R, Zhao L B, et al. A novel characteristic curve for failure prediction of multi-bolt composite joints[J]. Composite Structures, 2014, 108: 129-136. |
| [12] | Liu F R. Research on failure prediction methods for typical bolted composite joints[D]. Beijing: Beihang University, 2014 (in Chinese). 刘丰睿. 典型复合材料螺栓连接结构失效预测方法研究 [D]. 北京: 北京航空航天大学, 2014. |
| [13] | Ting R. Protruding tension head titanium 1/16 grip variation, HST12[R]. Torrance: HI-SHEAR Corporation, 1983. |
| [14] | Ramazan K, Cihan R C, Mehmet A, et al. Failure behavior of laminated composite plates with two serial pin-loaded holes [J]. Composite Structures, 2008, 82(2): 225-234. |
| [15] | Ay？e ？, ümran E, Recai F T. Progressive failure analysis of glass-epoxy laminated composite pinned-joints[J]. Materials and Design, 2012, 36: 671-625. |
| [16] | Aktas A, Dirikolu M H. The effect of stacking sequence of carbon epoxy composite laminates on pinned-joint strength[J]. Composite Structures, 2003, 62(1): 107-111. |
| [17] | Zhou S, Wang Z Q, Zhang J F. Influence of ply angle on failure response of bolted composite joint[J]. Advanced Materials Research, 2012, 383-390: 7128-7132. |
| [18] | Faruk S, Murat P, Onur S. Experimental failure analysis of mechanically fastened joints with clearance in composite laminates under preload[J]. Materials and Design, 2008, 29(6): 1159-1169. |
| [19] | McCarthy M A, Lawlor V P, Stanley W F. Bolt-hole clearance effects and strength criteria in single-bolt single-lap composite bolted joints[J]. Composites Science and Technology, 2002, 62(10-11): 1415-1431. |
