The lubricating oils are essential for operating engine with high efficiency. Therefore, the physical properties of oil such as flash point, pour point, kinematic viscosity, specific gravity and the American Petroleum Institute are necessary to be studied to indicate good quality of the lubricating oil. In this study, we compare the physical properties of two virgin oils with re-refining oil. The results indicated slight differences in the re-refining oil properties in comparing to virgin oils due to larger values of specific gravity and carbon residue, and lower value of flash point, pour point, kinematic viscosity, and American Petroleum Institute.
Cite this paper
Faqi-Ahmed, B. M. and Omar, K. A. (2017). Comparative Study between Physical Properties of Virgin Oil and Re-Refining Oil. Open Access Library Journal, 4, e3393. doi: http://dx.doi.org/10.4236/oalib.1103393.
Abdel-Azim, A. and Rash, M. (2001) Polymeric Additive for Improving Flow Properities and Viscosity Index of Lubricating Oils. Journal of Polymer Research, 8, 111-118.
https://doi.org/10.1007/s10965-006-0140-x
Abou El Naga, H.H. and Salem, A.E. (1984) Effect of Worn Metals on the Oxidation of Lubricating Oils. California Scientific Research, 96, 267-283.
https://doi.org/10.1016/0043-1648(84)90041-3
Rudnick, L.R. (2006) Synthetic, Mineral Oils, and Bio Based Lubricants: Chemistry and Technology. CRC/Taylor and Francis, Boca Raton, London, New York.
ASTM International (2004) ASTM D 4628: Standard Test Method for Analysis of Barium, Calcium, Magnesium, and Zinc in Unused Lubricant Oils by Atomic Absorption Spectrometry. ASTM International, West Conshoken, 1.
ASTM International (2004) ASTM D 4739: Standard Test Method for Base Number of Petroleum Products by Potentiometric Titration. ASTM International, West Conshoken, 1.
ASTM International (2004) ASTM D 524: Standard Test Method for Rams Bottom Carbon Residue of Petroleum Products. ASTM International, West Conshoken, 1.
Morinaa, N.A., Haquea, T. and Voonga, M. (2007) Compatibility between Tribological Surfaces and Lubricant Additives—How Friction and Wear Reduction Can Be Controlled by Surface/Lube Synergies. Tribology International, 40, 1680-1695.
https://doi.org/10.1016/j.triboint.2007.01.019
Fox, M.F., George E.D. and Totten, E. (2007) Sustainability and Environmental Aspects of Lubricants. In: Totten, G.E., Ed., Hand Book of Lubrication and Tribology, Chapter 13, CRC Press, Boca Raton.
ASTM International (2010) ASTM D2170/D2170M-10: Standard Test Method for Kinematic Viscosity of Asphalts (Bitumens). ASTM International, West Conshohocken.
https://doi.org/10.1520/D2170_D2170M-10
ASTM International (2014) ASTM D189-06: Standard Test Method for Conradson Carbon Residue of Petroleum Products. ASTM International, West Conshohocken.
https://doi.org/10.1520/D0189-06R14
ASTM International (2011) ASTM D3142/D3142M-11: Standard Test Method for Specific Gravity, API Gravity, or Density of Cutback Asphalts by Hydrometer Method. ASTM International, West Conshohocken.
https://doi.org/10.1520/D3142_D3142M-11
ASTM International (2016) ASTM D1796-11: Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure). ASTM International, West Conshohocken.
https://doi.org/10.1520/D1796-11R16