Micro-manufacturing emerged in the last years as a new engineering area with the potential of increasing peoples’ quality of life through the production of innovative micro-devices to be used, for example, in the biomedical, micro-electronics or telecommunication sectors. The possibility to decrease the energy consumption makes the micro-manufacturing extremely appealing in terms of environmental protection. However, despite this common belief that the micro-scale implies a higher sustainability compared to traditional manufacturing processes, recent research shows that some factors can make micro-manufacturing processes not as sustainable as expected. In particular, the use of rare raw materials and the need of higher purity of processes, to preserve product quality and manufacturing equipment, can be a source for additional environmental burden and process costs. Consequently, research is needed to optimize micro-manufacturing processes in order to guarantee the minimum consumption of raw materials, consumables and energy. In this paper, the experimental results obtained by the micro-electrical discharge machining (micro-EDM) of micro-channels made on Ni–Cr–Mo steel is reported. The aim of such investigation is to shed a light on the relation and dependence between the material removal process, identified in the evaluation of material removal rate (MRR) and tool wear ratio (TWR), and some of the most important technological parameters (i.e., open voltage, discharge current, pulse width and frequency), in order to experimentally quantify the material waste produced and optimize the technological process in order to decrease it.
References
[1]
De Grave, A.; Olsen, S.I. Challenging the sustainability of micro products development. Proceedings of the 2nd International Conference on Multi-material Micro Manufacturing, (4M 2006), Grenoble, France, 20–22 September 2006; pp. 285–288.
[2]
De Grave, A.; Hansen, H.N.; Olsen, S.I. Sustainability of products based on micro and nano technologies. Proceedings of the 4th International Symposium on Nanomanufacturing (ISNM 2006), Cambridge, MA, USA, 1–4 November 2006; pp. 40–45.
[3]
De Grave, A.; Olsen, S.I.; Hansen, H.N. Life Cycle Assessment of micro manufacturing process chains—Application to the microfactory concept. 2007. 4M Network of Excellence Web site. Available online: http://www.4m-net.org/files/papers/4M2007/367195/PID367195.pdf (accessed on 1 September 2011).
[4]
Nawata, S.; Aoyama, T. Life-cycle design system for machined parts—Linkage of LCI data to CAD/CAM data. Proceedings of the Second International Symposium on Environmentally Conscious Design and Inverse Manufacturing (EcoDesign'01), Tokyo, Japan, 12–15 December 2001; p. 299.
[5]
Qin, Y. Micro-Manufacturing Engineering and Technology; Elsevier: Amsterdam, The Netherlands, 2010. Chapter 25; pp. 394–404.
[6]
Okazaki, Y.; Mishima, N.; Ashida, K. Microfactory-concept, history and developments. J. Manuf. Sci. Eng. 2004, 126, 837–844.
[7]
Ban, Y.B.; Lee, K.; Oh, S. 5-axis micro-milling machine for machining micro parts. Int. J. Adv. Manuf. Technol. 2004, 25, 888–894.
[8]
Kussul, E.; Baldyk, T.; Ruiz-Huerta, L.; Caballero-Ruiz, A.; Velasco, G.; Kasatkina, L. Development of micromachine tool prototypes for microfactories. J. Micromech. Microeng. 2002, 12, 795–812.
[9]
Okazaki, Y. Microfactories—A new methodology for sustainable manufacturing. Int. J. Autom. Technol. 2010, 4, 82–87.
[10]
Plepys, A. The environmental impacts of electronics. Going beyond the walls of semiconductor fabs. Proceedings of the IEEE International Symposium on Electronics and the Environment, Phoenix, AZ, USA, 19–23 May 2004.
[11]
Liow, J.L. Mechanical micromachining: A sustainable micro-device manufacturing approach? J. Clean. Prod. 2009, 17, 662–667.
[12]
Boothroyd, G.; Knight, W.A. Fundamentals of Machining and Machine Tools, 2nd ed. ed.; Marcel Dekker, Inc.: New York, NY, USA, 1989.
[13]
Ho, K.H.; Newman, S.T. State of the art electrical discharge machining (EDM). Int. J. Mach. Tools Manuf. 2003, 43, 1287–1300.
[14]
Pham, D.T.; Dimov, S.S.; Bigot, S.; Ivanov, A.; Popov, K. Micro-EDM-recent developments and research issues. J. Mater. Process. Technol. 2004, 149, 50–57.
[15]
Lim, H.S.; Wong, Y.S.; Rahman, M.; Edwin Lee, M.K. A study on the machining of high-aspect ratio micro-structures using micro-EDM. J. Mater. Process. Technol. 2003, 140, 318–325.
[16]
Liu, K.; Paris, J.; Ferraris, E.; Lauwers, B.; Reynaerts, D. Process investigation of precision micro-machining of Si3N4-TiN ceramic composites by electrical discharge machining (EDM). Proceedings of the 15th International Symposium on Electromachining (ISEM), Pittsburgh, PA, USA, 23–27 April 2007; pp. 221–226.
[17]
Liu, K.; Lauwers, B.; Reynaerts, D. Process capabilities of micro-EDM and its applications. Int. J. Adv. Manuf. Technol. 2009, 47, 11–19.
[18]
Montgomery, D.C. Design and Analysis of Experiments, 7th ed. ed.; Wiley: New York, NY, USA, 2009.
[19]
Bissacco, G.; Tristo, G.; Valentin？i？, J. Assessment of electrode wear measurement in micro-EDM milling. Proceedings of the 7th International Conference on Multi-Material Micro Manufacture, Bourg en Bresse and Oyonnax, France, 17–19 November 2010; pp. 155–158.
[20]
Yu, Z.; Masazawa, T.; Fujino, M. Micro-EDM for three-dimensional cavities—Development of uniform wear method. Ann. CIRP 1998, 47, 169–172.
[21]
Bleys, P.; Kruth, J.P.; Lauwers, B.; Zryd, A.; Delpretti, R.; Tricarico, C. Real time tool wear compensation in milling EDM. Ann. CIRP 2002, 51, 157–160.
[22]
Yu, Z.; Masazawa, T.; Fujino, M. 3D micro-EDM with simple shape electrode. Int. J. Electr. Mach. 1998, 3.
[23]
Yu, Z.Y.; Kozac, J.; Rajurkar, K.P. Modelling and simulation of micro-EDM process. CIRP Ann. Manuf. Technol. 2003, 52, 143–146.
[24]
Modica, F.; Marrocco, V.; Trotta, G.; Fassi, I. Micro electro discharge milling of freeform micro-features with high aspect ratio, ASME 2011. Proceedings of the International Design of Engineering Technical Conferences and Computers and Information in Engineering Conference, Washington DC, USA, 28–31 August 2011. DETC2011-48331.
